-
product
Standard Voltage 50 Pin D-Type Cables - Connector to Unterminated for Pickering
The connector to unterminated cable assemblies below are suitable to use with Pickering cards and modules that utilize a standard voltage 50-pin D-type connector.
-
product
68 Pin 1.27mm Pitch Micro-D Connectors for Pickering
The connectors below are suitable to use with Pickering cards and modules that utilize a 96-pin micro-D connector.
-
product
8 Pin Power D-Type Female Connector, 40A, With Backshell
40-960-008-F
This connector is designed to allow users to directly terminate a cable with soldered connections.
-
product
13 Pin Towing Socket Tester ( For Halogen Light System)
7630
Peaceful Thriving Enterprise Co Ltd
The tester is to connect with the 12V 13-pin Euro-type socket. It can also connect with 7 pin socket through a 13-7 pin towing adaptor. The cable is long enough for user to do the test while sitting in the vehicle. The tester can also do self-test (not work for 7 pin socket), 12V power check, ignition and reversing light. Not available for Newer car with LED light. CAUTION: The self-test is not available with 13-7 pin towing adapter because there is no continuous feed via the 7-pin socket.
-
-
product
Mating Coax Connector And 20 Coax Pins Crimped (One End) To 3 Foot Wires
GX96404
Mating Coax Connector and 20 Coax Pins Crimped (One End) to 3 Foot Wires
-
product
15 Pin Breakout Interface
VSI-Breakout-15
The VSI-Breakout-15 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
product
Pull-Thru Adapter, Wired, QuadraPaddle, to 100 Pin ML SCSI, f/ NI PXI-6514/15, 6509
510140113
Pull-Thru Adapter, Wired, QuadraPaddle, to 100 Pin ML SCSI, f/ NI PXI-6514/15, 6509.
-
product
68 Pin 1.27mm Pitch Micro-D Cables - 68 Pin to Alternative Connector for Pickering
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 68-pin micro-D connector.
-
product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends, 2m HV, Exit Towards Pin 1
A050DF5-C-HA200
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Tinned Ends, 0.5m HV, Exit Towards Pin 1
A050DM5-T-HA050
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product
-
product
Cable, 25 Pin 1.27mm Pitch Micro-D, Female to Female, 2m
A025CFR-025CFR-5A200
This 2m long female to female 25-Pin Micro-D Cable Assembly is constructed from 18/0.1 (26 AWG) copper wiring with PVC insulation and screening to minimise crosstalk. Screwlocks are provided to secure the connectors to their associated products.
-
product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Tinned Ends, 1m HV, Exit Away From Pin 1
A050DM4-T-HA100
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Cable Assembly, Receiver, TriPaddle, 20", 200 Pin Male LFH with M3 Jackscrews
540105020105
Cable Assembly, Receiver, TriPaddle, 20", 200-Pin Male LFH with M3 Jackscrews
-
product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Male Adapter, .025" Round Post (Adapter Pin)
610138117
Primary mating contact 610138100. (May mate with other Twin Female contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
product
25 Pin D-Type Cables - Connector to Unterminated for Pickering
The connector to unterminated cable assemblies below are suitable to use with Pickering cards and modules that utilize a 25-pin D-type connector.
-
product
Micrograbber® Test Clip With .025" Square Pin
4521
Micrograbber test clip, Do-It-Yourself, available in ten colors
-
product
Dynamically Controlled, High Voltage Digital I/O PXI Card With Pin Electronics
GX5055
The GX5055 represents a new level of performance and capabilities for PXI-based digital instrumentation. Based on the proven architecture of the GX5050, the GX5055 offers high performance pin electronics and an enhanced timing generator in a compact, 6U PXI form factor.
-
product
9 Pin D-Type Connector, Male
92-960-009-M
This connector is designed to allow users to directly terminate cables with soldered connections. Users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed when using this product.
-
product
Cable Assembly, Receiver, 36", TriPaddle, 9 Pin FML D-Sub
540010020201
Cable Assembly, Receiver, 36", TriPaddle, 9 Pin FML D-Sub.
-
product
104 Pin D-Type Cables - Connector to Connector for Pickering
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 104-pin D-type connector.
-
product
Pin Moisture Meter with Bluetooth®
FLIR MR55
The FLIR MR55 is a pin-based meter with wireless connectivity, which offers the convenience to view readings from a mobile device via the FLIR Tools® Mobile app. Thanks to a built-in library of 11 material groups, users can tune the meter to the appropriate test material to improve measurement accuracy. This library is easy to access on the FLIR.com website by scanning a QR code on the back of the meter with a mobile device.
-
product
Standard Voltage 50 Pin D-Type Cables - Connector to Unterminated
The connector to unterminated cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
product
Cable Assembly, Receiver, 20", TriPaddle, to 37 Pin Female D-Sub
540016020103
Cable Assembly, Receiver, 20", TriPaddle, to 37 Pin Female D-Sub
-
product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Tinned Ends, 1m HV, Exit Towards Pin 1
A050DF5-T-HA100
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Cable Assembly, 50-Pin D-Type, Male to Male, 2m, Exit Towards Pin 1
A050DM5-050DM5-0A200
The 50-Pin Cable Assembly is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
7 Flat (Spade) Pin Trailer Circuit Tester
PT7893
Easily test trailer plug circuitry on most new light trucks, SUV's and RV's. Just plug the plug tester into the trailer plug socket and activate the lights, brakes, turn signal etc.
-
product
Solid State PIN Diode Transfer Switch, 100 MHz to 18 GHz
P9400C
The Keysight P9400C solid state PIN diode transfer switch offers outstanding performance in terms of port-to-port isolation, switching speed and low insertion loss over a broad operating frequency range of 100 MHz to 18 GHz. The P9400C is particularly well suited for ultra-fast RF and microwave switching applications in instrumentation, communications, radar, switch matrices and various other test systems where high isolation, speed and lifetime of a switch is critical.
-
product
SP3T RF Pin Diode Switches To 18 GHz
Pulsar Microwave manufactures 3-way absorptive and reflective switches for use in 50-ohm systems. These SP3T switches operate from 100 MHz to 18 GHz and handle 200 mW input power. VSWR performance is often 1.6:1 or better with 100 ns switching time. Minimum isolation of 60 dB is specified for most units. Absorptive and reflective switches require +5V and -5V power supply to function. Control logic is from 0 to +5 volts. All voltage and ground connections are made by feed thru and turret terminals, respectively.
-
product
200 Pin LFH Connector Blocks for Pickering
The connector blocks below are suitable to use with Pickering cards and modules that utilize a 200-pin LFH connector.
