Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
Product
96 Pin 1.27mm Pitch Micro-D Connector Blocks for Pickering Products
-
The connector blocks below are suitable to use with Pickering cards and modules that utilize a 96-pin micro-D connector.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-010-HI
-
The 40-230-010-HI (PXI) and 42-230-010-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 31.5Ω with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Audio Generator
AG-51
-
The AG-51 Audio Generator contains a low distortion 20 Hz to 200 kHz sine wave generator, an SMPTE standard intermodulation signal generator and a fixed frequency sine wave generator at 3.15 kHz for wow and flutter tests. Signal outputs are simultaneously available at levels of up to +20 dBm (equivalent sine wave power for complex signals) at separate left (L OUT) and right (R OUT) output connectors. Outputs may be selected for left (L) only, right (R) only, left and right in phase (L+R), and left and right in phase opposition (L-R). Fully balanced or unbalanced outputs at impedance levels 150 ohms or 600 ohms are front panel selectable. Three precision attenuators (10, 1.0 and 0.1 dB) provide a dynamic range of 99.9 dB in 0.1 dB steps. Attenuator dials display the output level directly in dBm in the 150 ohm source impedance configuration. Automatic output leveling circuitry with a built-in self-test feature provides a constant output level thereby eliminating the need for output metering. In the TEST mode the generator output level is reduced to zero, a useful feature during noise measurements.
-
Product
PXI Very High Density Multiplexer, 24-Channel, 8-Pole
40-675A-002-24/8
-
The 40-675A-002-24/8 is a 24-channel, 8-pole MUX and is part of our range of PXI very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
Product
TB-2650, Screw Terminal, 8x64, 1-Wire PXI Module Matrix Terminal Block
781131-03
-
The TB-2650 provides the necessary routing to configure the PXI-2531 or PXIe-2531 PXI Matrix Switch Module as a 1-wire 8x64 matrix. You can directly connect the TB-2650 to the front panel I/O connectors of the PXI-2531 or PXIe-2531.
-
Product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Ferrules, 2m
40-972-037-2m-MU
-
The 37-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) wire and can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to Female (Female Screwlocks), 2m
A200LMR-200LFR-5B200
-
This male to female 2m cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin connector and is constructed from 4 bundles of 50-wire round/flat ribbon cable. The connector assembly can be secured to the product by screwlocks.
-
Product
Cable 96-Pin Micro-D Female to Unterminated, Cut Ends, 0.5m
40-972B-096-0.5m-FU
-
The 96-Pin SCSI Style Micro-D to Unterminated Cable Assy is constructed from 28 AWG Twisted Pair Tinned Copper wire with Polyolefin insulation. Crosstalk is minimised. Wires are colour coded for easy connection. Metal Spring Latches are provided on the 96-Pin connector.
-
Product
MP CI set
-
The MP CI set up to measure coupling impedance is used to determine EMC characteristics of connectors and cables. The coupling inductivity defines the coupling inductance of external disturbance on the shield or on the ground with the desired signals. If the coupling inductivity is considered in the construction set-up and the pin or wire assignment of connectors or cables, then the connectors or cables will be more interference-resistant. The MP CI set-up for measuring coupling impedance can be used for following measurements at connectors or cables: 1. measurement of a single signal (common mode) 2. measurement of a symmetrical signal (common mode) 3. measurement of a symmetrical signal (differential mode)
-
Product
Fiberoptic Repeaters
-
*Cost effective task specific Fiber Optic Solutions for Satellite Radio and GPS over Fiber*End to end solutions complete with RF to Optical and Optical to RF component*Flexible powering options including DC over hybrid cable, local 48 VDC and AC*Utilizes industry standard fiber cables and connectors
-
Product
3/8" ID Contacts
-
VPC offers a range of pneumatic connectors that are ideal for use with automatic engagement interface systems. These pneumatic contacts also work well when used together with the VPC iDock Series.
-
Product
PicoClean MTP/MPO One-Click Cleaner
MTC-12
-
Shanghai Fibretool Technology Co.,Ltd.
Many troubles in optical communications equipment are caused by contamination on the optical connector end face.The MPO/MTP connector cleaner, employs microfibers designed specifically for optical connectors to remove even the smallest contamination not visible to the naked eye.
-
Product
2-in-1 High-Voltage Test Hood
LX-HVE900EC
-
The test cells are made of stable, highly insulating plastic and are closed by a swiveling, transparent cover. The built-in safety switch is used to lock the hood and release the high-voltage sources. This ensures that no high voltage is active when the door is open. There is a generously dimensioned wiring space in the floor of the test cage. An interchangeable adapter plate in the test cell - optionally with an interchangeable interface or an interchangeable adapter cassette - allows quick adaptation to different types of test items. Prepared openings enable connectors and other common interfaces or cable bushings to be easily attached. The hood is opened and closed almost effortlessly thanks to precisely coordinated gas springs.
-
Product
Cable Assy 68-Pin SCSI Micro-D M/F 0.5m
40-970-068-0.5m-MF
-
The 68-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28AWG) Copper Wire with Polypropylene insulation. Metal Spring Latches are provided to secure the connectors to their associated products.
-
Product
1000BASE-T1 MEDIACONVERTER
Art.-Nr.: TE-1401-1
-
The ideal physical layer conversion between Automotive Gigabit Ethernet and your PC system The 1000BASE-T1 MediaConverter establishes one direct point-to-point conversion between automotive ECU’s using 1000BASE-T1 and any standard Gigabit Ethernet device with RJ-45 connector.
-
Product
MiniPCI Express to M.2 PCIe Adapter (B-key)
SKU-089-12
-
MiniPCI Express Adapter has M.2 (B-key) connector. It allows connection M.2 modules with B-key to a MiniPCI Express circuit. Adapter can be installed in Full size or Half size MiniPCI Express circuits, and this Adapter supports PCI express, SIM and USB 2.0 interfaces.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber
40-850A-314-HI
-
The 40/42-850A-314-HI is a PXI/PXIe 4-channel multiplexer with MU (mini SC) connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Bias Tee's
-
A bias "T" consists of a feed inductor to deliver DC to a connector on the device side and a blocking capacitor to keep DC from passing through to the receiver.
-
Product
Cable Assembly, 78-Pin D-Type, Female to Unterminated With Cut Ends
A078HF5-C-0A200
-
The A078HF5-C-0A200 is a 78-Pin D-Type to Unterminated cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable connector to associated products. Has a 45 degree cable exit towards pin 1.
-
Product
Inspection Microscope/Video
-
Connector end face contamination is a big problem with fiber optic cables and patch cords and it causes network issues. If you are a professional technician, you need a quality optical microscope. The magnification of connector end faces will allow you to discover any quality problems such as scratches. You need to make sure you have a clean connection with no dirt and debris. Visual inspection is fast, easy and simple. Using this test equipment can help avoid problems.
-
Product
LXI 75Ω 6:1 Microwave Multiplexer 4-bank 2.5GHz 1.6/5.6
60-820-004
-
Our 60-820 Microwave Multiplexer range is suitable for switching 75 ohm signals up to 2.5GHz. With the capability of supporting up to 16 banks of 6 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted DIN1.6/5.6 style connectors. A 50 ohm version, the 60-800, is also available covering frequencies to 20GHz.
-
Product
20-Pin Scorpion Cable, Female to Unterminated, Cut Ends, 20A, 0.5m
A020AFR-C-2A050
-
This is a 0.5m long female to unterminated 20-Pin Scorpion cable assembly with cut ends constructed from 19/0.41 (14AWG) Silver Plated Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product.
-
Product
Cable Assembly, 9-Pin D-Type Male to Unterminated With Ferrules, 2m
40-972-009-2m-MU
-
A range of 9-Pin D-Type cable assemblies with unterminated connections at one end and constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
Product
PXI/PXIe MEMS Optical MUX, Dual 2-Channel, Multi-Mode, 62.5/125 Fiber, ST Connectors
40-855A-522-M
-
The 40/42-855A-522-M is a PXI/PXIe dual 2-channel multiplexer with ST connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Female, 0.5m, Exit Towards Pin 1
A050DM5-050DF5-0A050
-
The 50-Pin Cable Assembly is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
UHF Connectors
-
Pasternack UHF connector category contains many part numbers, the majority are RoHS and REACH compliant. UHF connector series in this category will terminate to coax or terminal. Pasternack UHF connectors are built to precise microwave and RF industry specifications. Connectors in UHF series are constructed in male, female or sexless gender with 50 Ohm impedance. UHF connector items are available in 4 hole flange, bulkhead, 4 hole panel or mountless options. These connector designs include clamp/solder, crimp/solder, field replaceable or solder attachment methods. Like the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this UHF connector series is in-stock. But not just in stock, these connector will also ship the same day as they are purchased.
-
Product
PXI Microwave Relay, Single SPDT, 26.5GHz, 50Ω, SMA, External Termination
40-781A-321
-
The 40-781A-321 (PXI) and 42-781A-321 (PXIe) are single SPDT 26.5GHz microwave relay modules with external terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50GHz in 50Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
Cable Assy 68-Pin SCSI Micro-D F/F 1m
40-970-068-1m-FF
-
The 68-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28AWG) Copper Wire with Polypropylene insulation. Metal Spring Latches are provided to secure the connectors to their associated products.
-
Product
RS-232 Micro Line Driver - DB9 Connector
Model 209
-
FEATURES: Compatible with PC; 386/486 Pentium Com Ports; Full Duplex to 19.2 KBPS; No AC or DC Power; Screw Terminals or RJ-11; Small Size. The Model 209F offers all the features of the Model 201 Short Haul Modem but in a package that is approximately one third the volume.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 62.5/125 Fiber
40-852A-118-M62.5-HI
-
The 40/42-852A-118-M62.5-HI is a PXI/PXIe 8-channel multiplexer with FC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
