Wire
See Also: Contacts, Harness, Connectors
-
Product
Cable Assembly 44-Pin D-Type Female to Unterminated With Cut Ends, 1m
A044HF4-C-0A100
Cable Assembly
The 44-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to the product by screwlocks.
-
Product
Filter Probe
350
-
AINES 350 NFP is a professional noise filter probe to use in a demanding environment. It is designed to make a technician's job easy while tracing a wire from a bunch of wires with electrical interferences. The 350 NFP is the best option for technicians compared to other available products in the market. Combined with the AINES 140 or 240 Tone Sets, the 350 NFP makes a formidable combination to identify a cable pair quickly and conveniently in a normal environment and in locations with electrical interferences as well.
-
Product
Spring Contact Probes
-
FEINMETALL offers a wide range of contact probe:ICT / FCT probes, short travel probes, double plunger probes, fine pitch probes, interface probes, wire harness probes, threaded probes, high current probes, switch probes, twist proof probes, push back probes, koaxial probes, radio frequency probes.
-
Product
Configuration Block For The 34934A Quad 4x32 Reed Matrix
34934C
Terminal Block
This configuration block provides flexible options for wiring rows and columns to D-Sub connectors.
-
Product
6U VPX Single Board Computer
VPX6-195
-
Curtiss-Wright Defense Solutions
Our VPX6-195 6U OpenVPX T2080 Single Board Computer (SBC) combines performance with the advanced I/O capabilities of the NXP's quad-core AltiVec enabled T2080 processor. Designed for SWaP-constrained applications, the VPX6-195 provides two independent processor cores on a single printed wiring board (PWB) with a wide range of standard I/O and each with a XMC mezzanine site to provide twice the processing power.
-
Product
RJ45 Replacement Port For XG2 Tester
#TXGPORT
-
*Easy field replacement*RJ45 port installs with two screws*No wiring required
-
Product
4-Pin Power D-Type Female to Unterminated With Tinned Ends
A008PF4-T-6A100
Cable Assembly
The 4-Pin Power D-Type Connector to Unterminated Cable Assy is constructed from PVC insulated 56/0.3 (12AWG) Copper wire. The connector can be secured to the product by screwlocks and the unterminated connections are coded to match the connector pin designation.
-
Product
Mini Coax, Contact, Receiver, two .025" Square Wire Wrap Posts
610104140
Coax Contact (ITA)
Mini Coax, Contact, Receiver, two .025" Square Wire Wrap Posts
-
Product
LAN Testers
-
A cable detector can locate open power cables, either live or without current, up to 300 V. A cable detector can locate cables, circuits, short circuits and ground wires. To perform these functions, it is not always necessary to disconnect electrically sensitive devices or to disconnect the power to the cable being tested.Many cable detector devices can also locate ferrous and non-ferrous metals, wood and plastic with high degrees of accuracy. A cable detector provides a safe way to test wall sockets for which no electrical plans or wiring information is available about the cables or their output. A cable detector is very versatile, as it ensures speed and safety when making holes in walls, ceilings and floors.
-
Product
Glow Wire Test Apparatus
GWT A2
-
GLOW WIRE TESTER (also known as Glow Wire Test Apparatus) is designed to carry out fire hazard testing as specified in IEC 60695-2-10 2000-10. Flammability test is to check the ‘Resistance to Fire’ of electrical insulators that touch directly conducting parts & also parts of insulators. This test is also referred in many other standards such as IS 11000, IS 3854 : 1997 / IS 1293 :1988 / IS 371 :1999 & IS 11000 Pt 2 Sec 1, IEC 60335, IEC 884/94, IEC 60598, IEC 61058, BS 6458, BS EN 60695–2-10,11,12, etc.
-
Product
Open Test Platform for High Performance Automotive Applications
TSVP
Test Platform
The R&S®TSVP family of products is an open test platform from Rohde & Schwarz ideal for high performance automated test equipment (ATE) applications. The chassis contains a mechanical frame, digital backplane, analog backplane, mains switching and filtering, power supply and diagnostic extensions. A highlight is the analog bus for routing measurement signals between different slots without additional external wiring.
-
Product
Cellular Phone/RF Signal/ Wired Camera/Bug Detector
SH-055GRV / 01125
-
This Cellular Phone Detector / RF Signal Detector / Wireless Camera Detector applies with fuzzy scanning technology to detect peeping cameras, tapping, cellular phones and other radio frequency devices
-
Product
Gauge Type T Thermocouple Wire
W-TW-40
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
ITA, I2 Micro ICon, 168 Position, With Oversized Backshell
410130106
ITA
The i2 Micro iCon ITA with oversized cable clamp is capable of holding up to 168 QuadraPaddle contacts. With a wider 1.97” footprint, it is ideal for applications requiring shielded twisted pair wiring or other wire types with oversized jackets. The 30-degree u-shaped cable clamp allows ITA modules to be pre-wired before assembly and can hold cable bundles with an oblong bushing effective diameter of 1.80". The removable cover allows easy access to wiring for maintenance and probing. Integrated spring locking tabs ensure even and secure engagement.
-
Product
Thermocouples
-
A thermoelectric device for measuring temperature, consisting of two wires of different metals connected at two points, a voltage being developed between the two junctions in proportion to the temperature difference.
-
Product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Tinned Ends, 1m
A025DM5-T-0A100
Cable Assembly
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
Drill Chuck Grips
-
Metal rods, wires, and plates and electronic components can be tensile tested using drill chuck grips. Electronic components are tested by placing the metal legs of the components in the grips, allowing different shaped components to be tested with the same set of grips.
-
Product
Loop Antennas
-
A loop antenna is a radio antenna consisting of a loop or coil of wire, tubing, or other electrical conductor, that for transmitting is usually fed by a balanced power source or for receiving feeds a balanced load.
-
Product
Test Lead Set
69128
-
Set of two (red, black) 32'' (813 mm) test leads.Each lead has alligator clips attached to both ends.Multi-purpose tooth pattern for better gripping of wires and test points.Recommended for general purpose measurements.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Ferrules, 1m HV, Exit Towards Pin 1
A050DF5-F-HA100
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable, 10 Pos Combicon to Pigtail, 1 Meter
190656-01
Multifunction Cable
The SH10M-10F Cable, sometimes referred to as SH10F-P, connects C Series DAQ devices with a 10-pin screw terminal to open signal wires. The SH10M-10F Cable is offered in different lengths.
-
Product
Wall Searching Metal Detector
HHB C
-
A Wall Searching Metal Detector, also known as a stud finder or wall scanner, is a tool used to locate hidden objects behind walls, such as metal pipes, electrical wires, and wooden studs.
-
Product
Inductor Products
-
Macom Technology Solutions Holdings Inc.
They provide uniformity, durability and repeatability in circuit fabrication. The coils are polyimide coated to protect from ambient contaminants, and to eliminate the need for conformal coating. Quartz substrates are rugged and reduce dielectric losses. Chips may be bonded using either conductive or non conductive epoxies, and wire bonded with gold wire or ribbon by thermocompression bonding.
-
Product
ITA, I2 Micro ICon, Wired, QuadraPaddle, 36", Flying Leads
410130409
Cable Assembly
ITA, i2 Micro iCon, Wired, QuadraPaddle, 36", Flying Leads This i2 Micro iCon comes wired with a flying leads cable assembly containing 168 QuadraPaddle patchcords with 24 AWG PVC.
-
Product
Sockets
-
Ironwood Electronics Sockets – Embedded gold plated wire elastomer (SG) – Stamped & Etched spring pins (SBT) – Embedded silver ball elastomer matrix (SM/SMP)– Compressible silver button in polyimide (GT/GTP)– Surface mount adapters for sockets (SF)
-
Product
Fine Wire Versatile Thermocouples ANSI
-
An exposed junction thermocouple is the simplest form of thermocouple. It consists of two pieces of thermocouple wire joined together with a welded bead. Since they can be made very small, an exposed junction thermocouple can provide a very fast response time.
-
Product
Pin-Line™ Collet Socket with Solder Tail Pins
Series 0513
-
Pin-Line Collet Sockets with Solder Tail Pins. Features: Rows of socket strips may be mounted on any centers and are end-to-end or side-by-side stackable for .100 [2.54] grid or matrix patterns. Available with solder tail or wire wrap pins. Consult Data Sheet No. 12014 for wire wrap pins. Break feature allows strips to be cut to the number of positions desired.
-
Product
Portable Static Grounding Kit
Grounding Kit
-
The portable grounding kit combines multiple shortened grounding rods with surface wire grounding techniques to provide acceptably low resistance for static grounding requirements in field operations.
-
Product
Rear Cover, S6, Tabletop Configuration, For Part # 310 122 100
310113431
Protective Cover
The Rear Covers are designed to enclose the wiring that runs from the S6 Receiver on the tabletop to the instrument cards below. This rear cover is used with the S6 Receiver Part # 310 122 100.
-
Product
Enclosure, G12x, Front Mount, 4 Cable Clamps, 12" Depth
410112856
Enclosure
Enclosure, G12x, Front Mount, Hinged Cover, 4 Cable Clamps, 12" DepthIncludes hinged cover and 4 cable clamps for discrete wiring. When cable clamps are open- stiffener bar can be removed for installing or removing cables without unplugging patchcords from assembly.Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
