Showing results: 256 - 270 of 389 items found.
-
NEGATIVE FILM -
Tester Soft Ltd.
Negative film and photomask inspection originated from the extensive use of printed circuit boards. Negative films and photomasks are used in large quantities. The early detection method is to use the "inspection light table" for inspection, which requires too much manpower and material resources, and manual testing may be due to eye fatigue and negligence.
-
Flann Microwave Ltd.
Flann offers a number of different types of cavity frequency meter. These are available with micrometer setting, where a look-up table is supplied to relate frequency to micrometer reading. Direct reading frequency meters are available with either a calibrated rotating drum or a digital display, and these are also available with a remote control interface to build an automated test system.
-
PAS 9782/GEN -
Precision Analog Systems Co.
The PAS 9782/GEN is a VME based, eight channel function generator card. Each channel contains a Direct Digital Synthesis (DDS) chip that can be programmed to generate sine wave output signals. This DDS device is a Numerically Controlled Oscillator (NCO), employing a phase accumulator, a sine look-up table and a 10 bit D/A converter.
-
PAS 9883/GEN -
Precision Analog Systems Co.
The PAS 9883/GEN is a VME based, eight channel function generator card. Each channel contains a Direct Digital Synthesis (DDS) chip that can be programmed to generate sine wave output signals. This DDS device is a Numerically Controlled Oscillator (NCO), employing a phase accumulator, a sine look-up table and a 10 bit D/A converter.
-
ICFP -
Ardent Concepts, Inc.
Ardent’s ICFP is a next generation coaxial cable termination toolkit for advanced system design de-embedding, de-bugging, and calibration. Designed for the lowest loss access to signal paths on an IC circuit footprint, this solution is a simple, cost effective alternative to expensive probers and x-y tables for Engineers who need to probe multiple signals at once.
-
DMX ADAPTER -
EMO Systems Canford Audio PLC
DMX protocol is a standard means of controlling lighting dimmers remotely from a control desk. The standard uses a three wire connection using 5-pin XLR type connectors. These adapters allow the E445, E446 and E447 table testers to be used to test the primary circuit of such cables. Two adapters are required for each cable tester.
-
DYNEOS AG
Versatility in terms of materials Taper controlled drilling Only top – quality components Intelligent laser machining software Beam focus adjustment Beam power (pulse energy) control Many options for system customization Table top system Small footprint Cost effective workstation User-friendly, flexible, upgradeable system control
-
LabStandard AIR -
Rotary Precision Instruments UK Ltd
Ultra precise rotary tables intended for fine inspection, metrology and test applications.The LabStandardAIR has been designed as a “Contact Free” system and eliminates features, which may detract from achieving the optimum rotational performance. The rotating elements are supported on super high precision, air lubricated, hydrostaticbearings and are not subject to disturbances associated with gear drives.
-
SY 8125 -
Hong Kong Songyang Industrial Ltd.
The devices are fully made by aluminum alloy materials and the table board is composed of fireproofing and heat-proof materials. The output voltage and current use soft startup and stop. It has the protection functions of voltage short circuit, current open circuit and power amplification exception. The device has the features of high stability, good reliability and large output power
-
Ingenieurbüro Dr. Hillger Ultrasonic-Techniques
The imaging ultrasonic testing systems of the USPC 30XX series are optimized for testing a wide variety of materials and provide high-resolution findings in the form of A, B, C, D and F images. The hardware consists of an industrial PC, in which a motor controller and an ADC card are installed, as well as a HILL-SCAN pulser/receiver unit. An overview of the available systems is given in Table 1.
-
Instron
Instron offers a variety of testing systems and rigs for static, quasi-static and dynamic loading of structures and components. This includes Component Test Systems, Shaking Tables, Road Simulators, Axle Test Systems, Full Vehicle Test Systems, Wheel Test Systems, Shock Absorber Test Systems, Elastomer Test System and Dynamic Torsion Test Systems.
-
Elecard Ltd.
A set of software products for broadcasters, corporate TV, sport, medical, surveillance system owners and system integrators to offer exceptional digital TV experience. Mature live encoder Elecard CodecWorks Encoder that might be configured to tasks of any complexity and Elecard CodecWorks 990 for IP to IP adaptive multiscreen transcoding. See the comparison table.
-
CT350 -
Dr. Eschke Elektronik GmbH
ICT test points: max 2736 CAD Data import Automatic program generator Powerful debugging tools Test coverage analysis Paperless repair station Logging- and statistic functions Full graphical functions Panel and multisite tests Fast adapter exchange High Pin Count-Interface On table optional usable shelf part.
-
USBDR-8 -
Alligator Technologies
Power worldwide with universal AC adapterDC power from 12V to 50V sourceInstall from 1 up to 8 channels per USBDR-8Daisy chain USBDR-8 to control up to 112 channels using just one USB portUSB 2.0 compatible communication Synchronize all USBPxx-S1 operation in tracking or dynamic control applications Operate on table top, wall mount, rack mount or DIN rail mount Optional DIN rail connection kit for mounting the USBDR-8 to DIN rail available Optional 19" aluminum rack mount plate available
-
Thorlabs, Inc.
Welcome to Thorlabs; below you will find links to our extensive Optomechanical product line, a subset of our entire line of photonics products. Optomechanics is a broad category that includes optical tables and breadboards, optical mounts and construction components, mechanical devices with integrated electronics, kits that make it easy to buy a popular set of components or a set of components that can be assembled to perform a specific function, and general laboratory supplies and tools. Because of the large selection, Optomechanics does not include translation and rotation stages and their controllers; instead those products have their own category.