Sequencers
-
Product
Analog Sequencers
-
Analog sequencers from Analog Devices integrate accurate comparators with the control functionality of power-on and power-down sequencing for voltage regulator banks. The comparators monitor the regulator voltage outputs and trigger the turn on of next rail in the system after a preconfigured time delay. Some members of this portfolio can be cascaded together, which provides scalable solutions to expand functionality across multiple devices. Our analog sequencers provide an easy to use solution for power sequencing challenges in cellular infrastructure, telecommunication, data communication, and data center applications.
-
Product
Digital Sequencers
-
The Analog Devices Super Sequencer ® portfolio offers a total power management platform for monitoring, measuring, sequencing, and margining a large number of voltages. Our comparators provide ±1% accurate monitoring of rails, while 12-bit ADCs offer voltage readback via a serial interface. Applications utilizing these devices benefit from sequencing that has been custom tailored to their needs by powerful state machine cores, as well as DAC banks to trim or margin regulators. Our digital sequencers include on-board EEPROM for storing devices parameters and for latching information for later analysis.
-
-
Product
Axle Damping Test Bench
C_MSD C 13.0 W220 | VP 215050
-
Maschinenbau Haldenwang GmbH & Co. KG.
The axle damping test bench C_MSD is characterised by a fast and precise mechanical testing of the axle damping. Through the frequency-controlled plate activation via electric motors, the maximum vibration amplitude is calculated and then the axle damping is evaluated according to the Lehr damping principle. The fully automatic test sequence, including the calculation of axle and vehicle weight, saves time and allows a reliable assessment of the axle damping.
-
Product
PXIe 16 Bit Arbitrary Waveform Generator - up to 625 MS/s on 1 Channel
M4X.6620-X4
Arbitrary Waveform Generator
The M4x.66xx-x4 series arbitrary waveform generators (AWG) deliver the highest performance in both speed and resolution. The series includes PXI Express (PXIe) cards with either one, two or four synchronous channels. The large onboard memory can be segmented to replay different waveform sequences. The AWG features a PCI Express x4 Gen 2 interface that offers outstanding data streaming performance. The interface and Spectrum’s optimized drivers enable data transfer rates in excess of 2.8 GB/s so that signals can continuously replayed at a high output rate. While the cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum waveform generators. So, existing customers can use the same software they developed for a 10 year old 20 MS/s AWG card and for an M4x series 625 MS/s AWG.
-
Product
1Gsps, 9 Channel, Logic Analyzer with Protocol Analyzer plugins and Hardware Compression
DigiView™ DV509
-
- Physical Channels: 9- Sample rate: 4ch@1 Gsps or 9ch@500Msps (4 ch. are sampled every 1ns or 9 ch. are sampled every 2ns)- Typical capture: 100M transitions (> 1B samples)- Hardware based triggers with 8 universal match circuits, and partitionable 16 stage sequencer- Adjustable Threshold (± 4V)- Real-time, Hardware-based, Adaptive Compression- Channels protected to ± 20V- Ground leads protected to ± 12V- High-quality test leads: 66 strand soft copper wires, flexible insulation, and gold plated connectors. Fit .025 square posts as well as the included clips.- Extra ESD protection- Streaming storage with auto fall-back to Store & Forward mode ensures large storage and reliability.- USB 3.0 (SS) or USB 2.0 (High Speed)- USB powered- Each DigiVIew includes all avialable Protocol Analyzer plugins (including: I2C, SPI, CAN, Async, Sync, 1-wire, I2S, TDM)- Free Plugin Developers' Kit- Requires Windows 7 or greater OS (32bit or 64bit)- Free Lifetime sofware updates.- 1 year warranty
-
Product
Counterfeit Defect Coverage Tool
-
The SAE Counterfeit Defect Coverage Tool is a dynamic, web-based application that supplements SAE Standard AS6171 authored by the SAE G-19A Test Laboratory Standards Development Committee. It provides potential test sequences for the identification of counterfeit electrical, electronic, and electromechanical (EEE) parts along a range of risk levels and EEE part types. Allowing users to compare alternative test sequences as a function of resources needed to implement those tests, the SAE CDC Tool is appropriate for those ordering counterfeit detection tests as well as those performing the tests.
-
Product
Resistance Wire Bonding
-
Electronic Systems of Wisconsin, Inc.
ESW's Resistance Wire Bonding System comes equipped with the latest features the market has to offer. Our system is capable of bonding armatures, stators or coils. The on-screen display in our bonder makes it easy to read, track, and record your bonding data. If desired, ESW offers complete electrical testing of the part prior to the bonding sequence as well. This ensures only good parts that have been electrically tested are processed through bonding. It is our duty to make sure you never have to worry about losing important information again. Our Sales and Engineering staff will work closely with you to make sure that a bonding systems will meet your needs. See the slideshow below to see some of our Resistance Wire Bonding Testers.
-
Product
ADB Bearing Sensor Tester
-
The ADB Sensor Tester (ADBT) has been designed to test 4B adjustable depth bearing (ADB) style temperature sensors in the field. During planned maintenance or periodic testing, the ADBT can be used as a diagnostic tool to verify the alarm and shutdown sequences of the control unit are functioning as expected. The unit operates in two testing modes, direct (heated) and indirect (simulated).
-
Product
Capacitive Sensors
-
Capacitive proximity switches detect conductive and non-conductive materials that can be in a solid or liquid state. They serve the purpose of monitoring product levels in containers, checking contents in filling and packaging systems as well as detecting, positioning, monitoring and counting objects, e.g. in sequence control systems, conveyor belts.
-
Product
Pickering Sequence Manager
-
Pickering Interfaces is delighted to announce the launch of sequencing service offering with all LXI platforms*. This functionality will allow a user to set predefined switch/simulation operations on the 1000+ Pickering PXI switch and instrument cards.
-
Product
Phase Rotation Testers
-
Our range of phase sequence indicators provide LED indicationof rotation. They are perfect for checking phase sequence in motors, pumps and air conditioning units.
-
Product
EFT Module for Teststand
test
The Electronics Functional Test (EFT) Module for TestStand provides out-of-the-box tools to speed up development of automated tests for electronic assemblies including PCBAs, subassemblies and final assemblies. Test engineers can develop, deploy and execute test sequences quickly and efficiently with minimal custom code development for a shorter time-to-solution.
-
Product
LCA TAP Plug-In
N4370P01A
-
Keysight Test Automation on PathWave (TAP) is a modern Microsoft .NET-based application for standalone use or in combination with higher level test executive software environments. Instrument plug-ins provide test steps that can be added to work-flow sequences without instrument level programming commands. The LCA plug-in steps further simplify automation by handling the interface to both the PNA instrument and the LCA optical hardware and software and providing the test steps for easy configuration.
-
Product
Cable/Harness Tester
LX-650
-
Shenzhen Lian Xin Technology Co., Ltd.
The system provides Chinese/English free switch operation interface;．·Up to 1000Vdc/700Vac Test Voltage．·256 Max. Test Points．·Auto Scan and Auto Pin Search．·The system provides advanced instant open-circuit, short-circuit, continuity test．·Intermittent Conductance Test．·Intermittent Open/Short Test．·Providing Double-End/Single-End Testing．·Large 320×240 LCD display．·Full Programming Sequence Test．·Versatile I/O Ports for application．·Statistics and Print Function
-
Product
Controller
YFC
-
The YFC-35D operates with only the YF-Series brushless electric screwdrivers. It is a single tool controller that offers programmable speed, angle, auto reverse and soft start options. The controller provides programmable fastening options for sequence based assembly automation applications.
-
Product
Axle Damping Test Bench
C_MSD C 2.5 W250 | VP 215049
-
Maschinenbau Haldenwang GmbH & Co. KG.
The axle damping test bench C_MSD is characterised by a fast and precise mechanical testing of the axle damping. Through the frequency-controlled plate activation via electric motors, the maximum vibration amplitude is calculated and then the axle damping is evaluated according to the Lehr damping principle. The fully automatic test sequence, including the calculation of axle and vehicle weight, saves time and allows a reliable assessment of the axle damping.
-
Product
Automatic Wire Test Set
AWTS
-
The Automatic Wire Test Set (AWTS) is automated test equipment that aids wiring diagnostics of electrical and electronic devices. The Test Control Unit (TCU) uses resistance measurements, capacitance measurements, and AC/DC voltage measurements to perform continuity, insulation, and isolation tests. The AWTS Laptop CPU, hereafter referred to as CPU, controls the AWTS. The Eclypse Language Integrated Test Environment (ELITE) is application software that controls the TCU. The majority of the hardware for a test is contained in the TCU. The 128pin connector on the TCU front panel provides 128 energizable test points. Switch Modules (SM) can be connected in sequence or daisy chained to the TCU and provide an additional 1024 test points; 128 of those are energizable.
-
Product
Phase Sequence and Motor Rotation Tester
PRM-6
-
The PRM-6 Motor and Phase Rotation Tester can test the motor rotation of 3-phase systems, and verify 3-phase receptacle wiring and phase sequencing with test leads.
-
Product
Portable Gas Calibrator
Model T750
-
Teledyne Advanced Pollution Instrumentation
The Model T750 is a portable, microprocessor based calibrator for precision gas analyzers. Using highly accurate mass flow controllers combined with compressed sources of standard gases, calibration standards are provided for multipoint span and zero calibrations. The T750 is housed in a high-density, molded travel case which includes an integral handle and wheels for durability and ease of use in the field.The Model T750 can be equipped with an optional UV ozone generator for accurate, dependable ozone calibrations, and production of NO2 when blended with NO gas in the included, internal gas phase titration (GPT) chamber. An optional photometer allows even more precise control of the ozone generator giving accurate and dependable ozone calibrations and enhanced GPT. A number of calibration sequences may be programmed into the non-volatile memory of the Model T750, covering time periods up to a year.
-
Product
Test Workflow Pro
test
Test Workflow equips engineers with application-specific tools so that they can choose the right one for the job—from graphical programing environments to no-code and interactive software applications. Engineers can use Test Workflow software to perform quick ad-hoc tests, build an automated test system, automate data analysis and reporting, develop test sequences, and more.
-
Product
PXIe 16 Bit Arbitrary Waveform Generator - up to 625 MS/s on 2 Channels
M4X.6621-X4
Arbitrary Waveform Generator
The M4x.66xx-x4 series arbitrary waveform generators (AWG) deliver the highest performance in both speed and resolution. The series includes PXI Express (PXIe) cards with either one, two or four synchronous channels. The large onboard memory can be segmented to replay different waveform sequences. The AWG features a PCI Express x4 Gen 2 interface that offers outstanding data streaming performance. The interface and Spectrum’s optimized drivers enable data transfer rates in excess of 2.8 GB/s so that signals can continuously replayed at a high output rate. While the cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum waveform generators. So, existing customers can use the same software they developed for a 10 year old 20 MS/s AWG card and for an M4x series 625 MS/s AWG.
-
Product
Text-Based Way to Connect & Disconnect Relays on ABex Modules
ABex Switching
-
The ABex Switching features a text-based way to connect and disconnect relays on ABex modules. Alias names for channels could be defined in a DUT specific topology file and then be used for text-based switching. These alias names are also shown in the Konrad System Manager allowing easy debugging of test sequences. The ABex Switching functionality could be either used out of NI Teststand with the provided test steps or via API from other programming languages.- Text-based switch routes- XML based topology for Alias mapping- Switch routes with support for Alias names- Seamless integration into Konrad System Manager
-
Product
MPO-MTP Polarity Instrument
JW8204
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW8204 polarity instrument is an intelligent product,which is designed for polarity judgment and on-off analysis in MPO/MTP cable production. Through the one-button automatically scanning operation, the state of cable on and off, polarity (wire sequence) state, alarm and error analysis can be quickly indicated. JW8204 provides a fast, accurate and highly efficient solution for MPO/MTP cable production, inspection of semi-finished product and finished product.
-
Product
VLF Diagnostics System
PHG 80 TD
-
Cable testing and diagnostics with the BAUR PHG 80 TD. The combination of the PHG 80 programmable test generator with the BAUR dissipation factor measurement system produces the cable testing and diagnostics system PHG TD. It is operated via PC control. Dissipation factor measurement and diagnostic testing sequences can be programmed in the menu, after which the dissipation factor measured values are automatically determined in various voltage steps and a final evaluation is conducted.* Biggest dynamic range of tan delta measured values from 1 to 10-4 with a cable capacitance >10 nF to 20 uF* High resolution +/- 1x10-5 applicable even in new PE/XLPE cables* Insensitive against interferences due to complete mains separation* Lowest time required for assessing a medium-voltage cable (3-phase approx. 1 hour)
-
Product
Informtest SAT
-
«Информтест САТ» - это инновационная, высокотехнологичная среда для разработки циклограмм, осуществления процессов моделирования и тестирования любых объектов контроля, не имеющая аналогов российского производства. Крупнейшие научные и производственные центры (РКК «Энергия», ОАО «ИСС» им. Академика М.Ф. Решетнева) уже используют данное программное обеспечение. Informtest Holding presents a unique software product "Automatic Testing System". This product eliminates the need to involve programmers in the development of open source software for testing and modeling, a CAD of the Informtest SAT shell and one specialist is enough. Thanks to an intuitive graphical interface, the development of any necessary sequence diagrams is not difficult even for a user unfamiliar with the basics of programming. The system is constantly being improved and updated. It is possible to make the necessary changes for each customer.
-
Product
VLF Diagnostics System
PHG 70 TD
-
Cable testing and diagnostics with the BAUR PHG 70 TD. The combination of the PHG 70 programmable test generator with the BAUR dissipation factor measurement system produces the cable testing and diagnostics system PHG TD. It is operated via PC control. Dissipation factor measurement and diagnostic testing sequences can be programmed in the menu, after which the dissipation factor measured values are automatically determined in various voltage steps and a final evaluation is conducted.* Biggest dynamic range of tan delta measured values from 1 to 10-4 with a cable capacitance >10 nF to 20 uF* High resolution +/- 1x10-5 applicable even in new PE/XLPE cables* Insensitive against interferences due to complete mains separation* Lowest time required for assessing a medium-voltage cable (3-phase approx. 1 hour)
-
Product
Installation Testers
-
Offers two models that verify the safety of electrical installations in residential, commercial and industrial applications. Has been developed to carry out the following safety measurements of electrical installations in accordance with EN 61557 and DIN VDE 0100: Insulation resistance, RCD tests, Low Ohm resistance, Earth ground resistance, Loop impedance, Phase sequence.
-
Product
Sequence Application Manager
AMFAX SAM
-
We have been building test systems for many years, as a result we find that many of the requirements our customers are looking for are very similar. This may be how a user logs in to the test system or the generation of test reports for example.
-
Product
ARINC 664 Part 7 Test & Simulation Interface for PCI Express
PCIe-C664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
