Test Connectors
-
Product
Flexible Test Connectors
-
Pin and socket sizes 22, 20, 16, 12 and 8 conform to MIL Spec dimensions. Whenever connector reliability is important, you’ll find NASA-approved FLEXCON test connectors. Applications include electronic, electrical and communications systems, computers, space vehicles, missiles, aircraft and other military equipment.
-
Product
Fiber End Face Interferometer
-
Thorlabs' GL16 End Face Interferometer measures and images the end face geometry of single- and multi-fiber connectors. A non-contact technique called scanning white-light interferometry (SWLI) provides high accuracy, repeatability, and reliability for fiber connector testing, particularly for pass/fail testing using IEC or Telcordia requirements. The system can be controlled locally through the touchscreen display or remotely through a browser-based application (see Software tab for details), allowing it to be easily integrated on the production floor.
-
Product
Flexible Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131H
Calibration Cable
The Keysight 85131H is a 62.2 cm (24.5 in) long1 flexible cable with a 3.5 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss greater than or equal to 16 dB. Insertion loss is 0.25 * sqrt (f) + 0.2 dB (where f is frequency is GHz) for the test port connector, and 1.5 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is characterized with a 90 degree bend using a 3 inch radius. Stability1 of the Keysight 85131H is less than 0.12 dB and phase is 0.13o * f + 0.5o, (where f is frequency in GHz).
-
Product
MPO/MTP Multi-Fiber Interferometer
-
Anfkom International Co.,Limited
It is an automatic and non contact fiber endface interferometer for both multi fiber and single fiber connectors. It can measure the geometry parameters of multi fiber connector such as fiber height,core dip, X and Y angel, radius of curvature with white light and measure geometry parameters of single fiber connector with red light. The software can display the surface of the connector in 3D image for a very short time, it need only 8s to test 12-core MT connector. It is intelligent , efficient,stable and accurate and very helpful in improving the quality of the product.
-
Product
10 Gb/s SFP/SFP+ Evaluation Board
EV-SFP-171
-
The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceiver such as 10 Gb/s(up to 16 Gb/s) SFP/SFP+ transceiver compliant with ANSI Fibre Channel FC‐PI‐5 for high speed electrical and optical specifications. This board provides SMA connectors for high speed TX and RX signals. The low speed control signals such as Tx_Fault, Rx_LOS and Rate_Selects can be controlled by using on board switches and test points. A connector for 2 wire serial interface to the module is also provided.
-
Product
Test Port Cable, 1 Mm
11500J
Test Port Cable
The Keysight 11500J test port connector has a length of 16 cm and a frequency range of DC to 110 GHz. The 11500J integrates with the Keysight N5250A network analyzer and Keysight 8510XF network analyzer systems.
-
Product
Pin-Mapping for Custom Connectors, Test Fixtures, UUTs | Cable & Harness Testers
PinMap™
-
Check out this fast and super-easy pin-mapping process enabled by our optional CableEye® PinMap™ software. Map as fast as you can move the probe from one pin to the next. Use on your custom connectors, test fixtures, specially-built connector panels, or pigtail adapters to your CableEye tester.
-
Product
Test Connectors
-
A wide range of standard test Connectors that can fit many of your applications and services. We offer a ideal solution for your testing needs in automatic or manual mode.
-
Product
Deutsch Test Connector Kit
148
-
We've had numerous requests by technicians to supply a similar set specifically fitted for Deutsch style connectors. These are mostly used on Heavy Duty and Equipment type vehicles, but are also used in RV, Marine, Motorcycles and Automotive applications.
-
Product
BNC (F) To Alligator Test Clips
2630
-
BNC (f) to alligator test clips. Converts BNC (male) cables / connectors to alligator test clips for test versatility. BNC connector is molded directly to the wire for pull strength durability and dust and moisture resistance.
-
Product
Connector Test
-
A connector test system which provides expansion of up to 160 Kelvin pair connections. The system incorporates high voltage AC and DC power supplies with a maximum output of +/- 2100 Volts peak for Hi Pot, Insulation resistance measurement. LCR bridge control is provided with 4 terminal multiplexing in order to add precision capacitance, inductance and resistance measurement capability. An integral H.V. capacitor bias option permits capacitance measurement to be made at up to 2.1kV.
-
Product
Test Connector Components
-
Any flat substrate, or bumped substrate, can be compressed against Z-Axis Elastomeric Connectors to make contact. The picture illustrates a Z-Thru Z-Alloy Connector Frame used to connect the DUT (Device Under Test) to a circuit board.
-
Product
7 Round Pin Tractor Trailer Circuit Checker / Maintenance Kit
#8029
-
Innovative Products of America
Test, clean and restore 7 round pin connections. Tester will verify tow vehicle is sending proper signal to the connector, while cleaning tools remove corrosion and verify proper pin size on both male and female truck/trailer plugs. For use with 7 round connectors. Tests tractor electrical circuits Removes corrosion from truck and trailer connectors Enhances electrical contact points Extends harness life Use as a pin wear gaugePatentedKit Includes: #7865L: 7 Round Pin Tractor Trailer Circuit Checker, #8024: 7 Round Pin Cleaner, and #8030: 2 ml DeoxIT Cleaner
-
Product
Production Connectors
-
Production Connectors for the manufacturing and testing of component assemblies. Handheld Production Connectors for assembly lines. Machine Mounted Test Connectors. Part-in-Place detection.
-
Product
54 Piece Automotive Test Connector Kit
146
-
This comprehensive test kit features a variety of terminal adapter sets which enable connection to most automotive vehicle connectors, both foreign and domestic. Terminal adapters connect via the included 48 inch stacking banana plug test leads. Connection to most DMM’s and scopes is no problem. Kit is designed to provide wide testing coverage and quicken the test process.
-
Product
Automatic Fixture Removal Software
S97007B
-
Automatic Fixture Removal (AFR) software is used to remove the effects of the fixture used to test coaxial connectors, which is required to make accurate measurements on the device
-
Product
Flexible Cable Set, 3.5 Mm (Test Port) To 7 Mm
85132F
Calibration Cable
The Keysight 85132F is a 62.9 cm (24.75 in) long¹ flexible cable set composed of two 3.5 mm female² to 7 mm connectors. Cable frequency range is dc to 18 GHz with a return loss greater than or equal to 17 dB. Insertion loss is 0.25 * sqrt(f) + 0.2, where f is frequency in GHz, for the test port connector and device connector. Phase stability of semi-rigid/flexible cables is specified with a 90 degree bend using a 4 to 3 inch radius. Stability¹ of the Keysight 85132F is less than 0.12 dB and phase is 0.13 * f + 0.5, where f is frequency in GHz.
-
Product
FPC Test Connectors
-
FPC Test Connectors (Clip Connectors) can easily be inserted and can be used for repeat testing, saving time and money as well as minimizing damage.
-
Product
Repeat Durability Tester
TIQ1000
-
It is a device to measure repeated endurance such as limit bending test of board, endurance test of mounted board, endurance test of connector, etc. Continuity data and load data can be obtained during the cyclic endurance test. Conforms to JEITA ET-7407 "Environmental and durability test methods for mounted CSP/BGA packages".
-
Product
Microohmmeter
AD-7100
-
4 Connectors measurement method, Max measurement time 10 sec Indicator of right connect test cables, Lock of test current connectors, Graphical backlight LCD display (240 x 128), True test current indicator, Temperature control of test current stability system,
-
Product
Connector Test Tools
-
Yokowo Connector Test Tools - BtoB Clips, Interface Connectors, and Tools for FPC Connectors
-
Product
Interferometers
-
Sumix interferometers are designed for inspection of fiber optic ferrules, patch cords, pigtails and bare fiber in the process of polishing and assembly. They enable you to check polishing quality, test connector end face geometry per IEC, Telcordia or your own custom standards and generate reports to supply with your patch cords.
-
Product
VME Backplane
VME J1
-
VECTOR Electronics and Technology, Inc.
Vector offers wide range of VME backplanes from 3 to 21 slots wide in J1 and J2 are 3U backplanes. All VME backplane boards are constructed from FR4 epoxy glass material and are assembled and tested. Press fit connectors are used throughout on all sizes.
-
Product
2-Channel Mandrel Free IL/RL Test Station
-
Shanghai Fibretool Technology Co.,Ltd.
This test station is designed specially for different connector on both sides patch cord(such as FC-SC, FC-LC, SC-LC…) and the duplex patch cord.The REF for insertion and return loss can set one time for those kind of patch cord, no need to change standard patch cord and interchange testing port connector on tester( Especially 2.5mm and 1.25mm interchange). For the tested patch cord, APC end no need to manually set standard patch cord length if PC end measured shortest length is 2.2M.
-
Product
BNC (F) To Minigator Test Clips
2631
-
BNC (f) to minigator test clips. Converts BNC (male) cables / connectors to minigator test clips for test versatility. BNC connector is molded directly to the wire for pull strength durability and dust and moisture resistance.
-
Product
Cover Extend Feature, GTE 10.00p
K8217B
-
Cover-Extend Technology (CET) extends the measurement capability of VTEP or nanoVTEP into powered testing by using the Boundary Scan output cell to test the connectors and socket signal pins. This capability extends the Boundary Scan limited access solution on non-boundary scan devices with the use of VTEP or nanoVTEP and CET signal conditioner card hardware.
-
Product
8-Channel VME Function Generator
V340
-
The V340 provides eight independent DDS-synthesized waveform outputs, each programmable for frequency and amplitude. Any output may be switched to a front-panel test connector, allowing in-crate calibration check without removing field cables.
-
Product
Loudspeaker Cable Testers
EMO E450
-
The EMO E450 cable tester will test for continuity, cross connection, and open circuit in cables fitted with NL8FC 8-pole and NL4FC 4-pole Speakon connectors, 3-pin XLR connectors, and 2 or 3 pole A-gauge jacks. EP retrofit kits are available to allow cables fitted with EP 4, 5, 6, or 8 pin connectors to be tested. The EP connectors fit in two pre-punched holes on the rear of the tester accessed by removing the blanking panel. The kit's flying leads plug directly into connectors mounted on the tester's PCB.
-
Product
Mini Multimode Power Meter and Mini LED Source
-
The KD Optics Mini Multimode power meter and Mini LED source are designed for the 850nm and 1300nm testing of multimode links, fibre continuity testing, connector testing, transmitter power testing etc.
-
Product
Flexible Cable Set, 2.4 Mm To 3.5 Mm
85134F
-
The Keysight 85134F is a 62.9 cm (24.75 in) long1 flexible cable set composed of a 2.4 mm female2 to PSC-3.5 mm female connector and a 2.4 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss greater than or equal to 16 dB. Insertion loss is 0.31 * sqrt (f) + 0.2, where f is frequency in GHz, for the test port connector and 1.8 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is specified with a 90 degree bend using a 4 to 3 inch radius. Stability1 of the Keysight 85134F is less than 0.12 dB and phase is 0.13*f+ 0.5°, where f is frequency in GHz.
