Igniter Testers
-
Product
DMX Tester
DMXter4 RDM
-
The DMXter4 RDM takes the next step in protocol testing. It provides expanded DMX testing along with growing support for RDM testing and configuration. Who else would you trust to support the new standard? The DMXter4 is simple to use. Eight buttons run its menu-driven software. The DMXter4 uses a back lit 40-character display. Some functions can drive a PC using the USB port. Software updates are done via the USB port.
-
Product
High-Voltage Testers
-
Voltage testers detect a wide range of AC voltage in overhead conductors with both audible and visual signals. Available in dual range and broad range, these testers are water resistant and include a durable carrying case, meaning they can be taken along and used on a variety of jobsites.
-
Product
Voltage Tester
HH2611
-
Handy, quick response and easy to use tool. Safe to use Non-Contact testing 90-220V AC voltage. Delect AC voltage without connecting into the wire circuit. Very bright LED and buzz sound alarm if voltage is present. Used to detect where the wire is broken. Used to detect whether an outlet is present of voltage. Used to detect a broken Christmas bulb out of a series of connected Christmas bulbs
-
Product
EMC Testers
-
The KES7000 System is a conductive immunity test system that is fully compliant with ISO7637-2 and ISO7637-3, international standards for EMC testing required for automotive electronic components. This system consists of the KES7700 Series Transient Surge Tester, KES7400A Series Voltage variation simulator and KES7100 application software dedicated to the KES7000 system. This product configuration supports JASO standards and the special test requirements of car manufacturers with options or custom orders.
-
Product
Ultrasonic Testers
-
Our Ultrasonic Thickness Gauge range, is the widest selection on the market with the best cost/performance ratio. On some of the models the warranties are extended up to 5 years while all of these gauges are efficiently and fully backed up and supported. These models are normally carried in stock for fast delivery.
-
Product
Tester For Maintenance
-
Mobile wiring testers in Multibox design or in customer specific housing for maintenance on military vehicles.
-
Product
Wiremap Tester
MicroMapper
-
Whether you're an electrical contractor, a home networking professional, datacom specialist or IT/network manager, the Fluke Networks family of powerful Voice/Data/Video (VDV) verification and troubleshooting tools will allow you to verify your work while delivering a quality installation.
-
Product
Universal Testers
-
All of our Universal Testers can be manufactured to utilize manual loading, manual loading with auto unloading, or automated load/unload. The interweaving of slip sheets between each PCB is available as well when utilizing an automated load/unload system.
-
Product
Insulation Testers
-
Rishabh Instruments Pvt. Ltd.,
Rishabh Insulation Tester is a Digital Insulation Tester with selectable test voltage up to 10kV and Insulation. Resistance measurement upto 20 TΩ. Ideal for testing insulation in live switchyards.
-
-
-
Product
Deadweight Testers
-
AMETEK Sensors, Test & Calibration
We provide the world’s only ball-type deadweight testers, where the ball and weights float on a thin film of air, which is virtually frictionless. This design eliminates the necessity to rotate the weights during testing, and allows the user to concentrate on the instrument itself. Our testers are engineered to offer user-friendly, safe operation, in the field, or in a lab. Both pneumatic and hydraulic testers are available.
-
Product
Electrical Tester
R580
-
Nidec-Read's R580 Electrical Tester provides an affordable test system for your bare board electrical test needs. You can easily integrate the R580 with your existing manual test fixtures or select from several fixture options from Nidec-Read. The R580 is supplied with opens/leakage test ability. In addition, you can include other advanced electrical test techniques.
-
Product
Voltage/Continuity Tester
CT-01
-
Standard Electric Works Co., Ltd
● Audible and optic continuity test.● Audible and optic voltage check.● Voltage protection : 600V● Robust and ergonomic housing.● For checking electric light bulbs, securings, wirings and so on.● Application : resistor, voltage, semiconductor, capacitor and so on.
-
Product
Compression Testers
-
Compression testing is a mechanical procedure for determining how a test sample will react to a force being applied across one side of the test sample.
-
Product
ADSL/ADSL2+ Tester
-
ST332B tester is a multi-functional and hand-held ADSL2+ test instrument with small size, specially designed for xDSL line test (xDSL include: ADSL, ADSL2, ADSL2+, READSL etc) and maintenance.
-
Product
Scratch/Shear Tester
3025
-
The Elcometer 3025 Scratch/Shear Tester is used to test the resistance of many materials to scratching, shearing, gouging, marring, scraping and engraving.
-
Product
Ethernet Tester
ProPlex IQ
-
Ethernet tester for entertainment production applications. Designed with input from production and staging professionals as an all-in-one device, it provides feedback and analysis on any Ethernet protocol, as well as network troubleshooting. It can act as a DMX cable tester, DMX receiver/transmitter, DMX timing analyzer, DMX recorder, RDM controller, or a bidirectional Ethernet-DMX gateway. It is also a PoE tester that can determine the capabilities of any connected PoE source. Finally, it can check SMPTE timecode or act as an LTC receiver/analyzer, and LTC transmitter, and users can use it to update Solaris/ProPlex firmware without a PC.
-
Product
Tensile tester
TS-2000
-
Advantage server motor, high quality warm gear gearbox, and precise roll bearing screw are adopted to ensure tensile tester machine the accurate control and results.
-
Product
Battery Tester
G5.BT
-
The G5.BT series is bidirectional regenerative. It was developed specifically for testing energy storage devices and is suitable for use in laboratories and on test benches. The modular and finely graded G5.BT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The G5.BT series has an outstanding current accuracy of <0.02% FS, an additional high-resolution current measurement range, and a fast current rise time in the 100 μs range. Ripple modulation, an integrated safety relay for PL c according to EN ISO 13849 and a powerful CAN multi-protocol interface (1 kHz, 16 bit) as well as functions to avoid reverse-polarity problems, current surges, and unwanted deep discharges make the G5.BT series the ideal, versatile battery module and battery pack tester.
-
Product
Adhesion Testers
-
Adhesion testing is the best way to determine whether your films and coatings adhere to substrates the way you need them to.
-
Product
Impulse Tester
MIG2412SPD
-
The MIG2412SPD is a impulse tester for testing SPD (Surge Protection Devices) in accordance with IEC 61643-1 and VDE 0675. Up to maximum 24kV/12kA making it suitable for testing Class I to III or in accordance with VDE Class A,C, D. The MIG2412SPD is a hybrid generator with a voltage wave shape 1,2/50 ìs at "no load" and a current wave form 8/20 ìs at short circuit for testing Class III (D) SPD connected to power line.
-
Product
Multifunctional testers
MI 3155 EurotestXD
-
MI 3155 EurotestXD is the newest flagship of Metrel’s most advanced line of multi-functional measuring instruments and is designed specifically for testing in industry. What differentiates this instrument from the rest is its ergonomic design and an intuitive user interface, encompassing a memory organizer and fully programmable AUTO SEQUENCEs, managed through a large colour touch screen display.
-
-
Product
Force Tester
CS2 Series
-
The CS2 Series are high quality digital force testing machines optimized for production and laboratory testing of applications up to 5 kN (1100 lbf). These force testing machines are an excellent choice for simple testing within plastic, rubber, packaging, pharma, cosmetic, electronics and wood.
-
Product
Multifunction Tester
COMBI521
-
COMBI521 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
Product
LAN Tester
TVR10/10/100
-
Triplett Test Equipment & Tools
TVR10/100/1000 LAN Tester is comprised of a "Main unit" and a "Remote Probe". The Main unit performs the bulk of the tests, such as determining the LAN device type (is it a hub/switch or PC?), the LAN speed and duplex (10, 100, 1000 MB/s, half or full duplex) and whether PoE (Power over Ethernet) is present without the need of the Remote Probe. The Remote Probe adds the ability to trace cable locations (by audibly tracing tones placed on the cable by the Main Unit) and to test the wiring of the cable (by decoding and displaying wiring information placed on the cable by the Main Unit).
-
Product
Insulation Testers
-
Precision Mastech Enterprises Co.
A specialized device that measures the electrical resistance of insulation on wires, cables, motors, and other equipment to check for damage or deterioration, preventing electrical failures, shocks, and fires by detecting leakage currents using high-voltage DC.
-
Product
Multi-Battery Tester
MBT-MIL
-
The ZTS MBT-MIL Multi-Battery Tester (MBT-MIL) provides a comprehensive means of testing the state of charge or state of power for more than 30 battery types. This microprocessor-controlled instrument is designed to test popular primary (non-rechargeable) and rechargeable batteries using a patented, high accuracy pulse load test. After a fully automatic test cycle, percentage of remaining battery capacity is indicated on the LED bar display.
-
Product
Phase Testers
-
Measurement on the voltage detection terminal and covered wireSafely used even for high-voltage bare wiresConsisting of the transmission and reception parts as well as the optical fiber wire connection those two parts
