Current Clamps
measure AC or AC-DC amperage without contacting conductors.
-
Product
Wireless Connectivity AC / DC Clamp Meter with 6000 count / NCV / SPT / 600A / 1000A (AC / DC) Current
MS-W376DFT
-
This is a external wireless connectivity digital clamp meter integrated with AC / DC hall effect sensor, 3-3/4 Digit 6000 Count, True RMS, auto and manual measurement.
-
Product
Current Monitor Probes
-
Current monitor/sensing probes measure superimposed RF currents flowing in conductors or cable harnesses. The main application is to measure conducted emissions to meet various EMC standards.
-
Product
Clamp-On Type Earth Resistance Tester / Leakage Current Clampmeter
KM 1620 / KM 1720
-
Kusam Electrical Industries Limited
KM-1620 / KM 1720 single-jaw type Earth Resistance Tester is widely used for earth resistance testing of the equipments in the field of power, telecommunication, as well as the other electrical equipments. It features easy operation, high-accuracy and good adaptation of testing environment.
-
Product
12-Ch SPST 5A-250VAC High Current Power Switching
YAV90CIN
-
12 Independent SPST relaysSwitching up to 5A 250Vac12 current measurement channelsGeneral inhibit inputCAN Control (or Ethernet with Ethernet to CAN Gateway)Drivers dll & VIs available
-
Product
Primary Current Injection Testers
-
Primary Current Injection Tester is designed for testing protective relay and circuit breakers and also testing the turns ratio of current transformers at high variable currents. A test current is injected into the primary side of a system to determine how the system behaves at particular levels of current. This test makes it possible to determine whether the relay will trip and how long the current needs to flow before the trip is initiated.
-
Product
Process Voltage & Current Data Loggers
-
Monitor and log virtually any process voltage or current output from your transducers.
-
Product
Resistors for Calibration of Current Measuring Systems and Sensors/Transducers
-
ChenYang Technologies GmbH & Co. KG
Is designed and made according to the Standard JB/T8225-1999 for DC resistors used in laboratory and electrical engineering.By using full closed structure and automatictemperature control it ensures resistor good long-term stability and small temperaturecoefficient. This DC resistor is very suitablefor DC current measurement and calibration of current measuring systems and current sensors. The maximal measuring current is 100A with measuring accuracy of ±0.02%
-
Product
Fluxgate 150A Current Sensor
LF03
-
Our LF03 current sensor works with the dynamic Fluxgate measurement technology. It is characterized by its simple, practical design and prevents high temperature drifts. Fluxgate technology uses the phenomenon of magnetic saturation to modulate the measured magnetic field and convert it into an electric field.
-
Product
Current Measurements Of PWM Or Inverter, AC/DC 1～50A, Φ16mm
CTF-50DC-U24V
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*AC/DC 1～50A*Current measurements for PWM or inverter
-
Product
Clamping Elements
-
Clamping elements from the LOCKED series provide a high level of safety. These ACE products clamp and decelerate loads and are suitable for perfectly controlled holding, both linear and rotary, in all processes.
-
Product
Leakage Clamp Meters
3921 CL
-
Standard Electric Works Co., Ltd
● Designed for testing AC current and AC voltage. ● 5 ranges for AC current testing.● The best resolution of leakage current measurement is 0.1mA.● Frequency selection : 50/60 Hz and Wide.● Data hold function.● Maximum reading.● Low battery indication.
-
Product
Auto-Ranging Digital Clamp Meter
DCM400
-
Expert Quality, auto and manual ranging clamp meter capable of voltage, current, resistance, diode and continuity testing. Maximum jaw - opening diameter of 36mm, backlit LCD screen, auto power off and a useful inspection light. Supplied with test leads, case and 3 x AAA batteries
-
Product
Oscilloscope Module, Clamp Meter Lead, Digital Multimeter
72-9185
-
The 72-9185 is a Clamp Meter Lead for use with digital multimeter.
-
Product
Current Probe
PA-629
-
*Maximum Current Value: +/- 200ADC, 140A RMS*1mA = 10mA, 100mA (switchable)*Rising Time: 1.2uS*Bandwidth: DC ~ 300kHz*Over Range Indicator*Battery, AC Power Supply Adaptor (free), dual usages
-
Product
1000 Amp AC True RMS Digital Clamp Meter
DL6403
-
True RMS reading on AC current and AC voltages provide accurate measurement regardless of the wave form, which makes this the ideal instrument for commercial and industrial applications where no linear loads are present.
-
Product
30A, 100MHz High Sensitivity Current Probe
CP031A
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
Bulk Current Monitoring Probe
MP-50
-
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
Product
Current Loop Adapter
OP-1C
-
This adapter supports current loop communications.The kit incorporates a communications circuit with photo-coupler isolation and constant-current power supply of insulated type, thus realizing not only monitoring but also easy communications testing with passive or active current loop devices.
-
Product
Hipot Current Calibration Load Resistors
HPRS-HIPOT-LOAD
-
The IET HPRS-Hipot-Load is an excellent replacement for the Fluke 5320A-Load Hipot current calibration load resistors. The IET high power resistive load can be used with the Fluke 5320A Multifunction Electrical Tester Calibrator or standalone. It provides a high power and high voltage load to various hipot tester to create the leakage current needed to calibrate various manufactures hipot testers.
-
Product
NI-9207, 500 S/s, 16-Channel C Series Voltage and Current Input Module
785040-01
-
500 S/s, 16-Channel C Series Voltage and Current Input Module - The NI‑9207 is a combination voltage and current input module designed with industrial systems in mind. It features eight current and eight voltage input channels, with built-in noise rejection.
-
Product
Eddy Current Chassis Dynamometers
-
Cradle- or single-roll (top-mount) dynamometers accommodating single- or tandem-axle vehicles, with continuous vehicle power ranges from 50 hp to 622 hp (37 kW to 464 kW), Taylor’s chassis dynamometers allow a top recommended speed of 90 mph (145 kph) at full load. Look to our experts to not only help you select your optimal system, but also to provide design, configuration, installation and training for a total solution that integrates seamlessly with your operation.
-
Product
NI-9265, 4-Channel C Series Current Output Module
779334-01
-
4-Channel C Series Current Output Module - The NI‑9265 is ideal for interfacing and controlling industrial current-driven actuators at high rates. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing … outputs to ensure safety and avoid driving actuators at system power on. The NI‑9265 requires an external power supply and includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity.
-
Product
Clamp on Meters
-
2000 counts LCD displayData hold for easy readingAuto-power offSafety as per IEC1010-1, Cat.II 1000V
-
Product
SolarIV Series Solar Cell Current Voltage Measurement System
SlarIV
-
SolarIV IntroductionOne of the key measurements needed for photovoltaic devices in the measurement of their I-V characteristics. Through measuring the I-V curves the user can determine physical performances of devices such as photo-electric conversion efficiency, fill factors and so on. Such data is important for reliable work in research and quality inspection. ZOLIX supply the SolarIV system and the most perfect, professional technical support.
-
Product
Voltage, Current and Power Measurement
-
Educated Design & Development, Inc.
For measuring current, especially higher currents and quicker than series ammeters. These units are considered the finest available. All units are extremely rugged, reliable, and versatile.
-
Product
Flexible Current Sensor Probe
CTA
-
The CTA current sensors convert ac current to an isolated 0-5A current with available ranges from 100A to 10,000A. Because the current sensors are flexible split core, installation is possible without shutting down the LV electrical supply, avoiding expensive down-time costs. Typical applications are retrospective energy monitoring in factories, offices buildings, process control data logging systems, where power, energy and current monitoring is important. Typical applications are factories, offices buildings, ac/dc VFD drives, welding, power conversion and power distribution. For all CTA current sensor models, a NIST/NPL (UKAS) traceable calibration certificate and certificate of conformance is supplied. All CTA sensors use UL94V0 or CSA approved materials. The CTA flexible current sensors are suited to permanent or semi permanent installation. The coil sensor is durable, lightweight, flexible and will easily clip-around a power cable. The 5A output from the CTA current sensor connects direct to installed metering, rotary metering or current transducers.
-
Product
AC Current Digital Clamp Meters
-
Precision Mastech Enterprises Co.
Handheld, safe, and non-contact electrical tools designed to measure alternating current (AC) without disrupting the circuit
-
Product
Portable Voltage and Current Instruments
-
Each model in our portable test equipment range is designed for accuracy and reliability, providing high performance and ease of use for applications. Products are used in various lab and field applications across industries such as research and development, semiconductor, and process control. For higher range electrical source and measure we have a series of bench multifunction calibrators and multimeters.
-
Product
Through Hole Type AC Current Sensor
CTA-30A
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*High accuracy and compact size.*Measuring range:AC 0.1A～30A.
-
Product
Current Sensing Chip Resistors
CS
-
*3W rating in 1W size, 1225 package*High purity alumina substrate for high power dissipation*Long side terminations with higher power rating
