PSE
-
Product
PoE Powered Device Analyzer for 802.3at & 802.3bt
-
The One-Box solution for 802.3 Ethernet Powered Device testing and verification including flexible emulation of PSE behaviors, scalable feature configurations, and plug’n play testing using a Windows PC.
-
Product
PowerSync Analyzer
PSA-3402
-
Compact and transportable configuration supporting PSE Conformance Test Suite and LLDP Emulation and Analysis options.
-
Product
PoE IEEE 802.3af/at 15.4W/30W Power Sourcing Equipment (PSE) For MIO SBC
MIOe-PSE
-
PSE delivers 15.4 W/30 W power to PDDual / Single port supportCompliant with IEEE 802.3 af/at standardSupports wide temperature -40 ~ 85 °CSupport Model: MIO-5354, MIO-2364, MIO-5376, AFE-E350, AFE-E420
-
Product
5G Router
ICR-4461S
-
ICR-4400, GLOBAL, NAM, 5x Ethernet, 1x RS232, 1x RS485, CAN, PoE PSE+, SFP, USB, SD, Without Accessories. 5G NR Cellular Connectivity, Sub-6GHz. 3GPP Release 16, Support both NSA and SA modes. Quad-core CPU with 1 GB RAM.
-
Product
Network AutoTester
LinkRunner® AT
-
Test and validate copper and fiber Ethernet connectivity in less than 10 seconds. Validate up to 30W 802.3af/at PSE with TruePower™ loaded Power over Ethernet (PoE) test. Verify twisted-pair cable length and wire-map in a snap.
-
Product
EMC Actuator for Accelerator Pedal
PSE-G
-
Pneumatically operated actuator for operation of accelerator handle. External set-point of the pedal actuator position via analog voltage to closed-loop pressure regulator in external valve box.
-
Product
PowerSync Programmable Load
PSL-3000
-
Sifos Technologies provides a one-box solution to facilitate testing and analysis of Power Sourcing Equipment (PSE) behaviors including basic compliance to the IEEE 802.3at and 802.3bt specifications. Each PSL-3000 test port is an autonomous and fully isolated instrument offering stimulus and measurement resources for 2-Pair PSE testing. Each test slot can be configured as an autonomous and fully isolated instrument for testing 802.3bt and pre-standard 4-Pair PSE’s from either test port in that slot.
-
Product
Rapid PSE And Chained Data Test Of 4-Pair And 2-Pair PSE's
-
Intuitive graphical user interface. Configures up to 24 2-Pair or 4-Pair ports for "snaked data path" testing. Verifies all PSE connections in the defined data path. Sequences user-defined PD emulations and PSE powering.Verifies powering to user-defined loading on all selected ports. Configures looped data paths across the selected ports. Support of 802.3at / 802.3bt LLDP power negotiations (PSL-3424L).
-
Product
EMC Actuator for Gas + Clutch Pedal
PSE-GK
-
Pneumatically operated actuator for operation of accelerator and clutch pedal in vehicles. External set-point of the pedal actuator position via analog voltage to closed-loop pressure regulator in external valve box.
-
Product
Universal Electrode Holder Series
PSE-1
-
The PSE-1 Universal Electrode Holder Series is designed for secure mounting of platinum, gold, titanium, copper, stainless steel, graphite, and glassy carbon electrodes in electrochemical experiments. Available in PTFE and PEEK body options, with standard, extended, L-type, rod, and custom configurations to accommodate a wide range of cell designs and laboratory setups.
-
Product
PID Testing Equipment
-
The potential induced degradation (PID) is addressed with the standard IEC TS 62804-1. The standard defines two methods that enable analyzing occurring PID effects in a specific PV module type. PSE AG offers the necessary equipment for the test in a climate chamber. The test equipment can work with any climate chamber on the market and is delivered turnkey. It comes with all necessary equipment, high voltage power sources, sensors, data acquisition and software.
-
Product
PoE Voltage Monitor Detect & Verify
PE-400
-
PE-400 is specific to test and verify PSE or Ethernet outlet either a standard/active PoE or a NON-standard/passive PoE to avoid damaging Non-PoE device as well as monitor and display available Voltage simultaneously. It built-in PoE interface controller to trigger on 802.3 af, at and bt switch and verify standard PoE type either 802.3 af or 802.3 at, and power source either End or Mid or both, and power polarity as well as display voltage values. The operational voltage which should be measured when installing a new PoE system or when you troubleshooting an existing system.
-
Product
PowerSync Programmable Loads (PSL-3424A, PSL3424L, PSL-3424M, PSL-3000)
-
Lower cost solutions for versatile 802.3at and 802.3bt Powered Device Emulation to support PSE system test and analysis
-
Product
EMC Actuator for Gas + Brake Pedal
PSE-GB
-
Pneumatically operated actuator for operation of accelerator and brake pedal in vehicles. External set-point of the pedal actuator position and brake pedal force via analog voltage to closed-loop pressure regulator in external valve box.
-
Product
Actuator For EMC Tests
PSE-G-MC
-
Pneumatically operated actuator for operation of throttle on motorcycles and 2/3 wheelers. External set-point of the pedal actuator position via analog voltage to closed-loop pressure regulator in external valve box.
-
Product
Power Manager Analyzer Suite for 802.3at, 802.3bt, & Hybrid PSE's
-
Tests 802.3 at/bt PSE’s with Any Combination of 2-Pair and 4-Pair PSE ports up to 90W per port. Automatically assess PSE PM Stability and Capacity Management. Tests PSE’s that grant power with Multi-Event, LLDP, or Both Multi-Event and LLDP. Automatically Adapts to PSE maximum assigned class (MAC) and power demotions on 2-Pair and 4-Pair ports. Tests PSE’s with up to 96 PoE Ports. Emulated PD’s are 802.3 specification compliant including built-in support for multi-event classification, power demotion, and 802.3at/802.3bt LLDP. Highly Informative Reports cover dozens of parameters using Colorful Graphics.
-
Product
EMC Actuating Unit for Gas+Brake+Clutch Pedal
PSE-GBK
-
Pneumatically operated actuator for operation of accelerator, brake and clutch pedal in vehicles. External set-point of the pedal actuator position and brake pedal force via analog voltage to closed-loop pressure regulator in external valve box.
