SAE
SAE International is a global body of scientists, engineers, and practitioners that advances self-propelled vehicle and system knowledge in a neutral forum for the benefit of society.
See Also: J1939
-
Product
SAEJ1962M-DE9M CAN OBD-II Cable, SAE J1962 to D-sub 9-pos F, 2m
193942-02
CAN Cable
9-Pin, Male SAE J1962 OBD-II Type A to 9-Pin, Female D-SUB - The OBDII9M-DB9F CAN Cable, sometimes referred to as the CAN OBD-II Cable, connects any NI high-speed CAN interface to an OBD-II compliant vehicle that has high-speed CAN on its diagnostic link connector in the passenger compartment. This high-quality injection-molded cable connects the CAN wires from the SAE J1962 connector to the standard CiA-DS-102 D-SUB connector wiring used by NI CAN interfaces. This cable is available with a high-speed CAN physical layer and no termination.
-
Product
GTEM cells
-
Meets IEC/EN 61000-4-20, SAE J1752/3, IEC 62132-2 and IEC 61967-2. The GTEM cell is, in principle, a tapered coaxial line (offset septum plate), which is terminated by a hybrid combination of discrete resistors and RF absorbers to achieve a 50 Ohm broadband match. It is applied for Measuring of Emission, Radiated, radio frequency field-immunity test.
-
Product
SUNTEST
XXL+ ST
-
Atlas Material Testing Solutions
The Atlas SUNTEST XXL+ ST is an extra-large xenon lamp flatbed instrument especially tailored towards the needs automotive parts testing. A dedicated model for testing automotive interior & exterior methods per the Society of Automotive Engineers (SAE) J2412 and J2527 test methods.
-
Product
Time-Triggered Ethernet / ARINC 664 Part 7 (AFDX®) / IEEE 802.3 Ethernet Deterministic Communications
TE2
-
Module TE2 is one of NAI's latest generation of advanced function Configurable Open Systems Architecture™ (COSA®) compatible modules. The TE2 is a certifiable, single-port, tri-redundant, deterministic Ethernet communications interface module that supports TTTech’s certifiable TTEthernet® End System product consisting of three traffic classes: SAE AS6802 (Time-Triggered Ethernet), ARINC 664 Part 7 (Avionics Full-Duplex Switched Ethernet (AFDX®), and/or IEEE 802.3 best-effort protocol. By supporting all three traffic classes, NAI's TE2 is the ideal solution for current users of IEEE 802.3 Ethernet, who plan to upgrade to Deterministic Ethernet (ARINC 664 Part 7 (AFDX®) or Time-Triggered Ethernet SAE AS6802) protocols in the future at any time without changing hardware.
-
Product
TDK Test Services
-
TDK Test Services offers testing to domestic and international EMC test regulations, including IEC, ISO, CISPR, and SAE. Test services are offered in our 3m semi-anechoic chamber, 3m fully-anechoic chamber, 10-meter open area test site, and our shielded conducted test chamber.
-
Product
Turbine Flow Meters
CT60, CT150
-
Flows up to 150 lpm (40 US gpm)Pressure up to 420 bar (6000 psi)Choice of 4-20mA and 0-5V outputs2-3 top ports as std for temperature / pressureBSP or SAE inlet / output portsFor use with oils, fuels, phosphate-estersBi-directional
-
Product
Dust Chamber
DUST
-
Designed specifically to meet the SAE J 575 and GM 9103 P test standards. Used throughout industries to evaluate a component's ability to function in a dust filled atmosphere.
-
Product
Spectrum and Signal Analyzer Frequency Extension Systems
SAE
-
The SAE modules are designed to interface with your existing microwave signal or spectrum analyzer and extend its frequency coverage to 500 GHz.
-
Product
TTEEnd System A664 Pro
-
The TTEEnd System A664 Pro board brings the full power of Deterministic Ethernet communication technology to aerospace certifiable hardware. The TTEEnd System A664 Pro card supports three standard traffic classes: Ethernet (IEEE 802.3), rate-constrained (ARINC 664 part 7) and time-triggered (SAE AS6802) traffic in parallel on one physical infrastructure. It offers redundancy management, as well as an IP/UDP profiled communication layer fully implemented in hardware. The card is designed for safety-critical applications and fully complies with DAL A levels of RTCA DO-254 and DO-178C.
-
Product
Simulators (Gen II)
J1939
-
The Au SAE J1939 simulators (Gen II, includes V1.00A releases and V2.00A releases) can generate SAE J1939 signal for up to three controller applications (CA): Engine, ABS and Transmission. Au J1939 simulators are designed so easy to use, even product line operator and sales personal can use them without Controller Area Network training. Au J1939 simulator can run all by itself and doesn''t require complicate software settings or user''s knowledge and experience on Controller Area Network. It is widely used as valuable tools for any situation from product-line test, incoming inspection, business demonstration to product development and product validation.
-
Product
Horizontal Flammability Tester
UI-TX40
-
Horizontal Flammability Tester – Horizontal Flammability Chamber is used to test textile and material used in vehicles horizontal burning rate when exposure to a small flame. Horizontal Flammability Test Method includes ISO 3795, ASTM D5132, JIS D1201, SAE J369, FZ/T01028, GB/T8410, GB/T20953 and etc.
-
Product
PCIe Board
79G5P
-
The 79G5P-TE2C0 is a full-height, half-length, PCIe board fitted & configured with the NAI TE2 function module. The TE2 is a single-channel, tri-redundant, Ethernet communications interface module that supports three traffic classes: Time-Triggered Ethernet SAE AS6802 (TTEthernet™), ARINC 664 Part 7 and Avionics Full-Duplex Switched Ethernet (AFDX®) and IEEE 802.3 protocol.
-
Product
Pole Plug Tester
SAE 7
-
When there’s no time to waste the SAE 7-Pole Plug Tester provides a fast, easy way to isolate lighting problems to the tractor or trailer. Use it to test the output of SAE 7-pole tractor light cords, while connected to the tractor or to your Square Wheel Industries Trailer tester.
-
Product
Brake Testing
-
Vehicle Brake Test and ABS TestingWe offer an easy-to-use measurement system for brake testing and ABS testing according to ECE, ISO, FMSSV, and SAE international standards. Our test system offers automated workflow, is flexible and robust and used for brake R&D, brake comfort and vehicle testing with regenerative braking. High-accuracy GPS and IMU hardware are available to achieve the highest possible velocity and distance accuracy.
-
Product
For AIM-58, AIM-68, AIM-78S And AIM-78H
10" Vehicle Docking Station
-
Compatible with 9 ~ 32 VDC in-vehicle power supplyEasy and instant single-handed docking and undockingAnti-theft locking mechanismExternal GPS antennaProgrammable function keysHigh-density connectorsCompliant with SAE J1455 for vibration and shock toleranceSafe and reliable design for vehicle applications
-
Product
Simulators
SAE J1708/J1587
-
The Au SAE J1708/J1587 simulators (Gen II, V1.00A release) can simulate up to 44 most frequently used Engine/Transmission/ABS parameters, warnings and diagnostic messages. Up to six Engine MID, three transmission MID and six ABS MID can be field configured. All editions can run independently (without personal computer). This family of simulators are designed very easy to use. It is widely used as valuable tools for any situation from product-line test, incoming inspection, business demonstration to product development and product validation.
-
Product
12/24/36V Conductance Battery Tester
MBT200
-
Tests 12V heavy-duty auto, truck, commercial, and marine batteries and 12/24/36V starter and charging systems including 42V mild hybrid systems. Eliminate tester input errors by choosing between automotive/truck battery or small automotive type batteries. LED bar graph immediately displays battery condition upon pressing TEST button. No conversion tables needed for CCA, SAE, IEC, EN or Ah. 390 to 650 CCA range (auto) and 650 to 1700 CCA range (truck).
-
Product
Salt Spray Chambers
-
Weice Testing Instrument Co.,Ltd.
The WTS series of salt spray chambers are manufactured and designed to meet the high quality requirements and standards, such as ISO, JIS, DIN, ASTM, IEC, GB and SAE. They are used to test the resistance capabilities of materials eroded by brine, these materials may be used in Electrical Appliances, Electrical Wire, Accessories, Luminaires etc.
-
Product
Full-Featured Life Cycle Test System
LCV
-
Configurations for testing to industry standards: IEC, SAE, BCILife Cycle Testing: Perform charge/discharge cycling of batteries or modules to obtain charge and discharge capacity, energy and DC internal resistanceAutomotive Battery TestingStarting, Lighting and Ignition (SLI) TestingTraction Battery Testing
-
Product
Aerospace Onboard Software Modules
ADS2 for Aerospace
-
Your product description goes here. The Aerospace Onboard System Development Process is guided by SAE ARP4754A. It consists of multiple levels of specification, design, validation and verification and is distributed between OEM and multiple suppliers of systems, subsystems and components.Due to the complexity of the development process, a consistent platform supporting model based validation, virtual and physical integration as well as requirement based verification at each level is of great importance for the industry.
-
Product
AS5653 Protocol Compliance Testing Solution
AS5653-PTP
-
Avionics Interface Technologies
Production Test Plan for SAE AS5653 - Full Suite of Verification tests to verify NC and NT operations in accordance with AS5653 - Utilizes AIT HS1760 Hardware - Automated Execution and Reports of Results - Python Test scripts - General exchange, sequence, and frame validation at the completion of each test - Production Test Plan for AS5653 Switch Compliance is also available
