-
Product
Optical Channel Monitor
-
Optoplex Optical channel monitor (OCM) uses proprietary thin-film interference filter technology combined with a micro-actuator and high-speed electronics. Optical channel monitor is used to measure critical information data on optical transmission signals in DWDM networks for monitoring signal dynamics, determining system functionality, identifying performance change, and providing feedback for controling network elements so as to optimize operational performance. In particular, Optoplex Optical channel monitor can automatically scan the C-, L- or C+L-band wavelength range and precisely measure channel wavelength, power, and optical signal-to-noise ratio (OSNR). See the following schematic diagram for OCM working principle.
-
Product
Optical Power Meter
TL-520
-
TL520 Mini-Designed Optical Power Meter is a self-developed test instrument which is widely used for installation, operation and maintenance of fiber-optic network. TL520 can test optical power within the range of 800~1700nm wave length. There are 850nm, 1300nm, 1310nm, 1490nm, 1550nm, 1625nm, six calibrated wavelength.
-
Product
Optical Spectrum Analyzers
-
Anritsu's Optical Spectrum Analyzers offer superior accuracy and reliability for evaluating a wide range of optical systems.
-
Product
Optical Networking Equipment
-
Guilin GLsun Science and Tech Group Co., LTD
Optical Networking Equipment by GLSN
-
Product
Absolute Optical Encoder
A2
-
Product DescriptionRestriction of Hazardous SubstancesThe A2 absolute encoder is a non-contacting optical rotary position sensor which reports the shaft angle within a 360 deg. range. As opposed to incremental encoders, the A2 reports the absolute position rather than the change in position. When powered up, it does not require a home cycle, even if the shaft was rotated while the power was off. In multi-turn mode, it tracks the position in a 32-bit counter as long as the power supply is maintained. Internally, an infrared LED flashes through a circular bar code onto a linear array sensor. The microcontroller decodes the image into a unique position. All user programmable parameters such as resolution, origin, direction and mode are permanently stored in an internal EEPROM
-
Product
Optical Voltage Probe
400-02
-
Srico’s optical voltage probe uses advanced, proprietary optical chip technology to achieve precise, interference-free measurement. Our sensor and optical fibers are made of dielectric materials. This facilitates a high degree of isolation between the voltage test point and the instrumentation system ⎯ at a safe distance of 100 meters and more. This system senses, measures, and transmits electrical data very accurately.
-
Product
Optical power meter with Optical laser Source
-
Shanghai Baudcom Communication Device Co.,Ltd.
The Multimeter combines a power meter with a 2-wavelength laser source,for optical fiber network installation and maintenance. With the large capacity of data storage,it's very convenient for field testing and transfering the test results to PC through USB interface.
-
Product
Optical Measuring Machines
-
QFP offers a complete line of optical measuring machines that allow us to offer the most suitable solution to satisfy any measurement need.
-
Product
Optical Switch
5504
-
The FOD 5504 Optical Switch is a unique handheld instrument for calibration sets and measurement automation. Routine comparison with Master device procedures in calibration laboratories, can be simply performed with before unachievable repeatability. No more need to move fiber and connect it repeatedly. Fix cables on a table, only once clean and connect patchcords.
-
Product
Active Optical Connectors
-
Panasonic Industrial Devices Sales Company of America
All-In-One Design, Integrated Fiber Cable for High-Speed Transmission.Panasonic, a worldwide leader in Connector Products, offers the V Series Active Optical Connectors. Featuring a built-in Laser Diode and Photodiode along with an electrical/optical conversion function, the V Series is an all-in-one optical transceiver capable of transmission rates up to 8 Gbps.
-
Product
Open Optical Encoders
-
An optical encoder is an electromechanical device which produces an electrical signal output proportional to the linear displacement of a linear guide or the angular position of an input shaft.Open encoders are exposed and feature no external integrated enclosure. The advantages of open optical encoders include the effective elimination of backlash, shaft wind-up (torsion) and other mechanical hysteresis errors.A rotary open optical encoder consists of a position measurement readhead and an accurate rotary scale marked either on the periphery of a ring or on the face of a disc.The readhead measures position by optically sensing the regularly-spaced scale markings and outputs this information as an analogue or digital signal.The signal is subsequently converted into a position reading by a digital readout (DRO) or motion controller.
-
Product
Optical Tweezers
PicoTweezers
-
Single or dual beam optical tweezers system based on an inverted microscope • 3D real-time video-based force measurements with sub-pN resolution • Huge free space above optical trap for all kinds of sample chambers and carriers • Manipulate and navigate trapped objects with nanometer precision • Easily extendable to fluorescence, STED, Raman spectroscopy, TIRF, or CLS.
-
Product
Automated Optical Inspection
AOI
-
No complex assembly process is complete without the ability to inspect and characterize the many different components used. ficonTEC’s fully automated INSPECTIONLINE systems acquire high-resolution pictures of the surfaces of interest and performs optical inspection based on the user’s criteria. For example, facet inspection of laser diodes, QC for coatings, surface inspection, top/bottom/side-wall inspection of semiconductor chips, and die sorting are just some of the many inspection tasks performed routinely by ficonTEC’s suite of inspection tools. As for all of ficonTEC’s systems, a modular approach permits the inspection platform to equipped with additional features – automatic tray handling and various feeding philosophies, testing capabilities (e.g. LIV), top/bottom chip inspection, and in-situ labelling.
-
Product
Optics Test Systems
Electronic And Visual Autocollimators
-
Optik Elektronik Gerätetechnik GmbH
OEG GmbH specializes in the use of autocollimators, collimators and telescopes for special applications in optical measurement technology in the wavelength range from 380nm to 1550nm (SWIR).
-
Product
MXI-Express Cable, Gen 1 x1, Fiber Optic, 200m
778959-200
MXI Express
MXI-Express Cable with Communication Levels up to Gen 3 x8 - The MXI-Express Cable connects a host interface to a PXI or PXI Express chassis. You can also use it for data communication between multichassis systems. NI offers it in different MXI communication levels and lengths.
-
Product
Optical Switches
-
Nanning Xionghua Photonics Technology
Optical Switches by Xionghua Photonics
-
-
Product
Optical Spectrum Analyzer
ID OSA
-
This instrument is a versatile Optical Spectrum Analyzer (OSA) based on a coherent detection principle provides picometer class spectral resolution across the C-Band (1528.5 – 1567.5nm).
-
Product
Optical Test And Measurement
-
Any type of fiber optic interconnection requires its interfaces to be free of dust and scratches in order to reach the lowest transmission loss. Small, handheld and battery powered inspection tools are available from AMS Technologies for inspection of fiber optic connectors in the field as well as high resolution type microscopes suitable for use in a production environment for qualifying the endface preparation. Additional S/W tools can support the user in making a quick decision if a certain defect is acceptable or if the surface fault disqualifies it for further use. Small and lightweight test equipment for measurement of the transmitted power in an optical fiber is needed wherever technicians handle optical fibers. Our product portfolio comprises light sources for various wavelengths, power meters for the visible and infrared and integrated solutions for sources and meters as well as optical time domain reflectometers (OTDR) coupled with visible wavelength light sources for easy fault detection within a fiber optic link.
-
Product
1211a Optical Receiver/Distribution
-
Precise Time and Frequency, Inc.
To complement the range of high quality frequency and timing references, Precise Time and Frequency, LLC. has now introduced a new Optical Time Code Receiver, with Auto Switching, a full complement of time code outputs, and Ethernet/RS232 remote monitoring/control interface.In addition to the auto switching capability, the new ptf 1211A delivers up to thirty six channels of Time Code outputs, including re-transmission of the optical input. The unit can accept a pair of inputs (usually from separate primary and backup sources), and provides monitoring of both the inputs and outputs for signal integrity.If the primary input fails, the unit will automatically switch to the backup input and indicate a primary signal fault.Full remote monitoring and control via RS232 and Ethernet interfaces includes telnet, http (web browser), and SNMP protocols.
-
Product
3D Optical Profilers
-
ZYGO's 3D Optical Profiler instruments enable precise, quantitative, ISO-compliant, non-contact surface measurement and characterization of micro- and nano-scale surface features, capturing up to two million data points in just seconds. Applications range from topography and waviness to roughness and microstructure characterization on samples as that vary from ultra-smooth sub-angstrom optical surfaces, to extremely rough and diffuse 3D printed surfaces.
-
Product
Optical Light Source
STC-OLS201 series
-
Shanghai Stone Communication tech Co., Ltd
a simple and cost-effective fiber optic tester,it is usually used together with fiber optic power meter to measure the optical loss on fiber cables. STC-OLS201 series light source provide multiple wavelength output, the wavelengths can be required on customer specific requirements (the Max wavelength is 5, such as 850/1300/1310/1490/1550nm).
-
Product
Optical Controllers
-
Teilch’s compact DM controller for the Kilo DM is capable of delivering 16bit resolution over 220V and with dynamic range of 1kHz. System is directly integrated with the Zif Socket, eliminating the need for cables and providing a direct mechanical connection from the bench mount to the DM.
-
Product
Optical Comparators
-
Starrett optical comparators provide a time tested, cost effective, solution for non-contact measurement. Optical comparators are used for an exceptionally wide range of dimensional inspection applications.
-
Product
Optical Radiation Meter
ORM400
-
The ORM400 Optical Radiation Meter has a USB 2.0 interface and is supplied with powerful calibration features and data display functions. It is ideally suited to display the measurements from the DH400 range of detectors as well as third party current generating detectors.
-
Product
Optical Inspection Machine
3D AOI
-
3D AOI latest optical inspection machine 1. No part dead angle, 4-way projection, complete measurement 2. Part height measurement, accurate measurement of defects 3. Multi-piece inspection without additional program 4. DLP digital projection, program editable height measurement
-
Product
Optical Transimpedance Amplifiers
-
Analog Devices optical transimpedance amplifiers offer a complete, high performance, single chip solution for converting photodiode current into a differential voltage input. Supporting data rates from 155 Mbps to 11.1 Gbps, our transimpedance amplifiers are ideally suited for data communications and telecommunications applications supporting lay protocols including 1×, 2×, 4×, and 8× Fibre Channel, 10GBASE-LX4, SONET/SDH up to OC-192 with FEC, and 10 Gigabit Ethernet. Our transimpedance amplifiers feature low input referred noise current, high input current, and low power dissipation.
-
-
Product
Automated Optical Inspection (AOI)
TR7700 SIII 3D
-
TRI’s ground breaking 3D AOI solution delivers the fastest hybrid PCB inspection combining optical and blue-laser-based true 3D profile measurement for the highest automated defect symptom coverage possible. Integrated state-of-the-art software solution and third generation intelligent hardware platform offer stable and robust 3D solder and component defect inspection and with high inspection coverage and easy programming.
-
Product
Co-Packaged Optical Interleaver
-
Co-packaged interleaver consists of a pair of iterleavers in the same package. There are three input ports and three output ports. The interleaver pair may contain one interleaver (Mux) and one deinterleaver (DeMux), or a pair of (Mux) interleavers, or a pair of (DeMux) interleavers. Customers can specify configurations according to their design and applications.
