Fiber Fault Locators
-
Product
PXI Fault Insertion Switch, 6-Channel, Two Fault Buses, 30 A
40-191B-012
Fault Insertion Unit
The 40-191B is a PXI fault insertion switch using solid state switching elements and is capable of carrying 40A on single channel or 30A on all channels at the same time and provides a robust solution to high current fault insertion.
-
Product
- RS-485 to Fiber Optic Converter
Model 276A
-
FEATURES: Data Rate to 1 MBPS; ST Connectors; DB-25 Connector; Half-duplex operation; Extends distance of RS-485 network to 6,600 ft (2 km) on multimode fiber cable. The Model 276A provides the capability of transmitting an RS-485 signal via a fiber optic link.
-
Product
MIL-STD-1553 Fiber Optic Bus Extender
FO-1553
-
Avionics Interface Technologies
Extends MIL-STD-1553 bus access to over 1 mile for remote access - Dual redundant, single and dual stream options available - Both Transformer and Direct coupling modes supported - Uses fiber optic 1.0625 Gbps data rates for low latency over long distances - Optical signaling is not affected by electrical noise and interference - Simple and easy to use solution, no software setup or configuration required - Ideal for applications where test equipment is separated from UUT
-
Product
Electrical DfT & Fault Coverage Analyzer
TestWay
-
TestWay's electrical DfT analyzer enables designers to validate designs at the schematic capture stage, to ensure that adequate measures have been included to comply with the manufacturers test requirements. The ability to verify that PCB designs have been developed with adequate Design-for-Test in mind, is key in determining the most effective test strategies and accurately calculating fault coverage, which is crucial in improving competitive advantage, lowering cost and ensuring product quality.
-
Product
Fiber Optical Switch at Single Mode Latching 1310/1550nm 5V with LC/PC Connector
SUN-FSW-1x2H
-
Guilin GLsun Science and Tech Group Co., LTD
GLSUN 1×2H Mechanical Optical Switch Fiber Switch Features·Low Insertion Loss·Wide Wavelength Range·Low Crosstalk·High Stability, High Reliability·Epoxy-free on Optical Path·Latching and Non-latchingGLSUN 1×2H Mechanical Optical Switch Fiber Switch Applications·R&D in Laboratory·System Monitoring·OADM·MAN (Metropolitan Area Network)·Network Security and MonitoringGLSUN 1×2H Mechanical Optical Switch Fiber Switch SpecificationsParameters Unit SUN-FSW-1×2HWavelength Range nm 1260 ~ 1650Test Wavelength nm 1310 / 1550Insertion Loss 1, 2 dB Typ: 0.8 Max: 1.0Return Loss 1, 2 dB SM ≥ 50Crosstalk 1 dB SM ≥ 55PDL dB ≤0.05WDL dB ≤0.25Repeatability dB ≤±0.02Operating Voltage V 3.0 or 5.0Durability Cycles ≥ 10 MillionSwitching Time ms ≤8Optical Power mW ≤500Operating Temperature ℃ -20 ~ +70Storage Temperature ℃ -40 ~ +85Relative Humidity % 5 ~ 95Weight g 14Dimension mm (L )22.5×(W)11.8×(H)10.2 ±0.2Note: 1 Within operating temperature and SOP.2 Excluding Connectors.
-
Product
Fiber Amplifier - Node With Supply
FANS 811-812
-
- AGC - Automatic Gain Control- Higher RF at next connected Node- Maintain MER/BER for Digital FTTH Transmission- High Quality DFB Lasers with Isolators- Variable SLOPE/GAIN Control- Input Wavelength : 1310/1550nm- Output Wavelength : 1310nm- Digital Display of Optical Level- External FusesPower Options :- Mains 220VAC, 50Hz- 12V DC / 2 Amp- 40VDC from “40V/RF out” connectors
-
Product
Yamasaki Optical Fiber Identifier
TF916
-
The Yamasaki TF916 Optical Fiber Identifier is an essential part of any professional fiber optic toolkit. By inserting fiber into the Yamasaki TF916 Optical Fiber Identifier head, the Yamasaki TF916 Optical Fiber Identifier can be used to identify traffic, traffic direction, frequency and optical power within any singlemode optical fiber. The sleek black outer housing is comprised of an anodized aluminum to make it lightweight and tough. Also included with the Yamasaki TF916 Optical Fiber Identifier are four adaptor heads that are specifically designed to suit various optical fiber types with minimal bend loss. The easy to read ultra-bright LED display and audible tone make operation easier and can save you valuable time in the field.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 62.5/125 Fiber
40-852A-218-M62.5-HI
Multiplexer Module
The 40/42-852A-218-M62.5-HI is a PXI/PXIe 8-channel multiplexer with SC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
RF Over Fiber
-
Quintech Electronics and Communications Inc.
Transmit and Receive Fiber Optic Signals.
-
Product
Multi-Function Transient Fault Recorder
TR-3000
-
The TR-3000 is the only tool you need to capture and diagnose power system anomalies. With multiple recording modes and continuous transient oscillography, you will never miss an event. The TR-3000 captures high speed transients and long term system disturbances with enough memory to give you a complete view of the system disturbance. The TR-3000 takes the place of several devices: • Fault and Disturbance Recorder • Transient Fault Location • Phasor Measurement Unit • Power Quality Monitor • Sequence of Events Recorder.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber, FC/PC Connectors
42-850A-114
Multiplexer Module
The 40/42-850A-114 is a PXI/PXIe 4-channel multiplexer with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
MXI-Express Cable, Gen 1 x1, Fiber Optic, 10m
778959-10
MXI Express
MXI-Express Cable with Communication Levels up to Gen 3 x8 - The MXI-Express Cable connects a host interface to a PXI or PXI Express chassis. You can also use it for data communication between multichassis systems. NI offers it in different MXI communication levels and lengths.
-
Product
Fiber Adapter
USB Serial Optical Converter
-
*Optical data transmission*Glass fiber or POF*Optimal galvanic isolation*USB bus-powered*Virtual serial interface*Baud rate up to 115kBit / s
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 62.5/125 Fiber, ST Connectors, With Interlock
42-850A-514-M62.5-HI
Multiplexer Module
The 40/42-850A-514-M62.5-HI is a PXI/PXIe 4-channel multiplexer with ST connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Blockage Locators
-
Shenzhen Noyafa Electronic CO.,LTD
Noyafa Blockage Locator can be used in both household and engineering. The sensing range is enhanced, and it is free from external interference. It can pass through the 60cm-thick cement wall and the pipe blockage under the floor to reduce the removal area. Accurate detection and adjustable sensitivity.
-
Product
Ground Fault Locator
GFL-1000
-
The GFL-1000 ground fault locator is used to pinpoint faulty grounding where electrical cables have breakage and lost to the ground. The GFL-1000 is recommended by NERC PRC-005-2 to inspect for unintentional grounds for VLA, VRLA and NiCad batteries every four calendar months. Included software allows for data management analysis.
-
Product
PXI 30A Fault Insertion Switch 6-chan 2-bus
40-191-012
Fault Insertion Unit
The 40-191-012 is a PXI fault insertion switch using solid state switching elements and is capable of carrying 40A on single channel or 30A on all channels at the same time and provides a robust solution to high current fault insertion.
-
Product
Mini Fiber Optic, Patchcord, Receiver, 36", Multimode, 62.5/125, Single Ended
7-416804000-036
Fiber Optic Patchcord
Mini Fiber Optic, Patchcord, Receiver, 36", Multimode, 62.5/125, Single Ended.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 50/125 Fiber, FC/PC Connectors, With Interlock
42-850A-114-M50-HI
Multiplexer Module
The 40/42-850A-114-M50-HI is a PXI/PXIe 4-channel multiplexer with FC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
1.5µm PM Fiber Amplifier ( PM EDFA )
HAPM4000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM4000 is a Polarization Maintaining Optical Amplifier which working in 1528~1563nm operating wavelength. Adopt Polarization Maintaining Erbium-doped fiber (PM-EDF), output optical power range 13~26dBm, extinction ratio >20dB.
-
Product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass, Single-Mode, 9/125 Fiber, LC Connectors
42-860A-422
Switch Module
The 40/42-860A-422 is a PXI/PXIe dual insert/bypass switch with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
Digital Fiber Sensor
FX-550L
-
Panasonic Industrial Devices Sales Company of America
Panasonic IO-Link technology makes it possible to continuously collect and process data and to control the sensor. This allows users to implement predictive maintenance and to monitor operation in machines and assembly lines. Processing the multitude of data requires users to invest in know-how and time. Panasonic has developed a self-diagnosis function for each sensor type. This function sends sensor data via IO-Link to a higher-level fieldbus, thus informing about the state of the sensor directly. This way, the amount of production data and the work needed to analyze the data is reduced.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Single-Mode, 9/125 Fiber
40-852A-118-HI
Multiplexer Module
The 40/42-852A-118-HI is a PXI/PXIe 8-channel multiplexer with FC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Cable Fault Locator
TX2003
-
6 km (19,000ft) 0.5mtr dead Zone Selectable Cable Impedance Warble Tone Generator Rapid Fault Location Large 128x64 LCD with Backlight Scratch Resistant Display Environmental Protection IP54 CE Approved 3yrs Manufacturers Warranty 60 Hours Battery Life
-
Product
Fiber Splitters & WDMs
-
Wuhan Sunma Technology Co., Ltd.
Optical Splitter is used to split the fiber optic light into several parts at a certain ratio. It is an important component used in Passive Optical Network (PON), therefore also called PON Splitter. There are mainly two kinds of PON splitters: one is the traditional fused type splitter known as FBT Coupler or FBT WDM splitter, which features competitive price; the other is the PLC Splitter based on the PLC (Planar Lightwave Circuit) technology, which has a compact size and suits for density applications. SunmaFiber provides both PLC splitters and FBT coupler splitters for EPON/GPON Systems.
-
Product
Optical Fibers and Modules
-
Optical fibers are at the heart of everything we do. We embed as many functions as possible directly into the fibers to make systems based on our fibers simpler, cheaper, and more reliable.
-
Product
Fiber Optic Loopback
LC/SC/MTRJ
-
Fiber Loopbacks is designed to provide a media of return patch for a fiber optic signal; typically it is used for fiber optic testing applications or network restorations. For the testing applications, the loopback signal is used for diagnosing a problem. Sending a loopback test to network equipment, one at a time, is a technique for isolating a problem.
-
Product
Fiber Optic Test Solution
Eye-BERT Micro 10G
-
The Eye-BERT Micro 10G is a low cost, easy to use, all-in-one XFP based fiber optic test solution offering high performance bit error rate testing at a fraction of the cost while providing a rich set of features not found in other bit error rate testers. Features include: variable bit rate, user programmable patterns, diagnostic monitoring, and wavelength tuning (per XFP capability). Additionally, with a click of a button, the Eye-BERT Micro 10G will automatically test an XFP module based on the information it reads from the transceiver and generate a detailed test report complete with manufacturer, part number, serial number, date code, fiber type, link length, speed, and test results. The Unit is supplied with anti-skid bumpers and is small enough to be integrated into larger systems for dedicated link verification.
-
Product
ULI-211CI -Triple Isolated RS-232/422/485 (Terminal Block) To Multi-Mode Fiber Converter (ST Connectors) DIN Rail Mounted
BB-FOSTCDRI
Terminal Block
Converts serial data signals to multi-mode ST fiber optic2 KV 3-way optical isolation (input/output/power); EMI/RFI protectionData rate: up to 115.2 kbpsWide operating temperature: -40 to +80 °CDIN mount, IP20 plastic case10–48 VDC power source required (not included, sold separately)UL Class 1 / Division 2
-
