Showing results: 976 - 990 of 2437 items found.
-
TBHPF1-9KHZ -
TekBox Singapore Pte. Ltd.
9 kHz Highpass Filter for protection of spectrum analyzer or EMI-receiver RF inputs against high amplitude subharmonics and residual 50 Hz voltage in conducted emission measurement set ups
-
BOP Series -
Kepco, Inc.
Kepco's bipolar BOP power supplies are available in 100W, 200W and 400W sizes. For applications requiring higher power, see Kepco's 1KW High Power BOP. For applications requiring higher voltage, Kepco's Series BOP-HV are available in 500V and 1000V models.BOP are high speed power operational amplifiers that can be used to provide dynamically agile voltage for test and simulation. They are not general purpose power supplies. By the nature of the bipolar high speed design, they do not have any energy-storage noise discriminating output capacitors. These power supplies offer ultra low noise and ultra low ripple at the output and are MIL-STD-461 compliant.
-
B-1013-6 -
ROSS ENGINEERING CORPORATION
Ross Engineering Corporation’s High Voltage Megmeter® series are unique battery powered DC hipot tester and meter. Models are available for withstand testing of insulation up to 50kV DC, as well as measuring leakage current as low as 0.001 microamp and resistance as high as 30 million megohms when testing underground cable, rubber safety gloves, vacuum interrupters, high voltage devices and all types of electrical insulation. All models have an over current trip feature to minimize arcing damage. Completely portable with rechargeable 12V battery which can be recharged from an automobile or 115V, 230V AC.
-
Analog Devices Inc.
A difference amplifier is a special purpose amplifier designed to measure differential signals, otherwise known as a subtractor. A key feature of a difference amplifier is its ability to remove unwanted common mode signals, known as common mode rejection (CMR). Unlike most types of amplifiers, difference amplifiers are typically able to measure voltages beyond the supply rails, and are used in applications where large dc or ac common-mode voltages are present. They are ideal for current and voltage monitoring. Analog Devices offers a range of difference amplifiers, optimized for low distortion, low power, or high voltage performance.
-
4E2-1 -
The Eastern Specialty Company
The Knopp 4E2-1 Voltage Tester is designed to detect electrical potential (voltage) between the third rail and ground on high voltage electrified transit systems. Two, redundant neon bulbs are used to indicate the presence of voltage. The prod handle and the tester housing are both made from moisture- and oil-resistant laminated phenolic. The prod tips are made from stainless steel. The tester housing includes a rubber hand guard to guide the operator in proper placement of his or her hand. There are no exposed metal parts other than to the two prod tips. All internal connections are soldered.
-
HH2205B -
Colluck Company Limited
High Accuracy (Basic Accuracy 0.5%). 3-3/4 Jumbo LCD display 3260 count with symbolic signs and bargraph. Double Injection Casing. Auto Ranging High Voltage test up to 1000V DC and 750V TRMS AC. Higher Current test up to 20A AC/DC
-
DRS20 -
APPLICOS
The DRS20 is a dual-channel reference source offering ultra high precision and stability and provides a +/-10 V output. The output current can be up to 10 mA and the 4 wire connection provides a 1 µV/mA load regulation. The high precision and stability is achieved by using a temperature controlled voltage reference.
-
HH2205L -
Colluck Company Limited
High Accuracy 0.8%. Jumbo LCD display 4000 count, 22mm figure heigh. Full Auto Ranging with symbolic display. Rated CAT II 1000V. High Voltage test up to AC 750V and DC 1000V. Higher Current test up to 10A (fuse protected)
-
J2101A -
PICOTEST Corp.
The injection transformer is presently the prevalent method for connecting the network analyzer to the circuit being tested, and is primarily used for control loop stability measurements. The goal of the transformer is to inject a signal into the control loop being measured, without impacting the performance of the loop. In order to accomplish this to a reasonable degree, The transformer is isolated and therefore is capable of floating on a high voltage, such as a Power Factor Corrector (PFC), which is often close to 400VDC. Measuring voltages that exceed the voltage rating of the FRA inputs require attenuation probes.
-
J2100A -
PICOTEST Corp.
The injection transformer is presently the prevalent method for connecting the network analyzer to the circuit being tested, and is primarily used for control loop stability measurements. The goal of the transformer is to inject a signal into the control loop being measured, without impacting the performance of the loop. In order to accomplish this to a reasonable degree, The transformer is isolated and therefore is capable of floating on a high voltage, such as a Power Factor Corrector (PFC), which is often close to 400VDC. Measuring voltages that exceed the voltage rating of the FRA inputs require attenuation probes.
-
Renesas Electronics Corp.
Renesas is a leading low-dropout regulator (LDO) supplier in low power handheld applications with world-class differentiated single and dual LDOs which have ultra-high PSRR up to 3MHz, low input voltage range, tiny packages, and ultra-low noise and quiescent current. Renesas' high current LDOs support up to 3A and have industry-leading fast load transient response, tightest voltage output accuracy at full load and over the full junction temperature, and lowest dropout voltage in its class.
-
Eclipse Tools
Built-in white LED illumination light provides convenient work in dark areasDetects AC voltage from 90 to 1000 VAC without metallic contactCompact size with pocket clip easily fits into pockets or tool pouchesRed LED and audible alarm if voltage is presentEntire outer surface is non-conductive for safety, helps avoid high voltage shockPowered by two 1.5V AAA batteries (not included)CAT IV 1000V Safety rating.Applications: Electricians, maintenance staff, service and safety personnel, and even homeowners
-
72-13610 -
Tenma
*Triple channel linear DC power supply*Dual channel adjustable & one channel fixed*Constant current & constant voltage operation*Forced ventilation & temperature cooling system*LED digital tube display shows voltage and current simultaneously*Low ripple & low noise, output on/off control*Overload and reverse polarity protection*115VAC/230VAC (50Hz/60Hz) AC input voltage and 0.01% high regulation*12-month limited warranty *view Terms & Conditions for details
-
72-13600 -
Tenma
*Triple channel linear DC power supply*Dual channel adjustable & one channel fixed*Constant current & constant voltage operation*Forced ventilation & temperature cooling system*LED digital tube display shows voltage and current simultaneously*Low ripple & low noise, output on/off control*Overload and reverse polarity protection*115VAC/230VAC (50Hz/60Hz) AC input voltage and 0.01% high regulation*12-month limited warranty *view Terms & Conditions for details
-
EP Series -
Lumetronics
A range of high grade laboratory power supplies capable of delivering upto 450W of power. These custom built models are easy to use, provide medium power, low voltage output and are capable of operating in laboratory or industrial environments. They havebeen designed keeping in mind the specific requirements of electronic and photometric laboratories and provide the most frequently required voltage and current ratings, while offering a safe overload protection. These power supplies are capableof supplying the maximum specified current at low voltage settings also.
