-
Product
Indoor Multi-Light source of Measurement System for PV Cell
-
King Design Industrial Co., Ltd.
The multi-light source measurement system is capable of execute I-V measurements by Real-Time One-Sweep Method (RTOSM), which not only removes the capacity effect but also meets the requirements of SEMI PV57-1214. The measurement process is controlled by designed program, thus the measured I-V curve, Pmax/Isc/Voc/… etc, could be exported automatically.This system is applicable to DSSC/OPV/Perovskite measurements.
-
Product
Low Concentration Photo-Voltaic (LCPV) & High Concentration Photo-Voltaic (HCPV) Cell Testing
-
Concentrated PV Cell testingPhoto-biological studies of plants, animals, and cell culturesSemiconductor testingPhoto-toxicity researchMaterial degradation researchAccelerated UV and solar exposure testing of color fastness and material stability for paints, textiles and plasticsAtmospheric photochemical pollution research
-
Product
Solar Cell Tester
REOO RO-GTM2615
-
REOO RO-GTM2615 Solar Cell Tester is designed for PV cell manufacturing inspection, enabling fast cell performance inspection and stable electrical quality verification. Built for solar factories, it improves cell testing accuracy and maintains stable operation across PV cell production lines.
-
Product
Testing for Si Solar Cells Using High Performance CCD
EL Imaging Tester
-
EL Testing for Si Solar Cells using High Performance CCD. The determination of luminescence (photo emissions) in solar cells is an important characterization tool. Typical solar cells often have defects which limit the efficiency or lifetime of a cell. Many of these defects are visualized with Luminescence Imaging. By using this technique, the manufacturing process can be optimized to produce better cells. Luminescence Imaging takes advantage of the radiative inter-band recombination of excited charge carriers in solar cells. The emitted photons can be captured with a sensitive CCD camera to obtain an image of the distribution of the radiative recombination in the cell. This distribution is determined by the local excitation level, allowing the detection of electrical losses, thus mapping the diffusion length of minority carriers as the emitted light is low intensity and in the near infra-red range, the CCD camera has a high sensitivity wavelength from 900 to 1100 nm with little thermal noise. This CCD camera provides excellent resolution of 1024 x 1024 pixels with a large 1μm pixel size, multi-megahertz readout speed, and robust USB 2.0 connectivity. The EL CCD Camera is the ultimate high-performance CCD camera for electroluminescence and photoluminescence imaging for Photovoltaic (PV) Cells and Modules. This camera combines low noise electronics and optimal sensitivity in NIR.
-
Product
Resistivity Cell For N1413 (26/50 Mm Electrodes)
N1424B
Resistivity Cell
The N1424B is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424B to the B2985B/87B.
-
Product
Resistivity Cell For N1413 (50 Mm Electrodes)
N1424A
Resistivity Cell
The N1424A is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424A to the B2985B/87B.
-
Product
PV Reference Cells
-
Our silicon-based solar irradiance sensors (Si-Sensors) measure the irradiance intensity on your photovoltaic system with utmost precision.
-
Product
Solar PV Testing Services
-
Atlas Material Testing Solutions
Can your product stand up to the harshest environmental conditions? Atlas Testing Services can provide manufacturers with the data they need to demonstrate long-term durability and to support warranty and performance claims while reducing the costs associated with aftermarket product failure.
-
Product
PV Measurements System
PH-IQE200
-
PV Measurements offers to combine a Spectral Response/QE/IPCE system with an I-V system into one compact measurement system. Depending upon the configuration required for your devices,it may share a test fixture.This reduces overall system cost.
-
Product
Fuel Cells
-
continuously variable contact pressure ensures complete reproducibility of the test conditions ● independent of the thickness of the fuel cell components due to the self-adjusting piston and special sealing concept ● no connection and disconnection of hose- or cable connections for the exchange of cellFixture necessary ● fast &Easy clamping of the cellFixture without tools and precise exchange of the internal cell components ● maximum power density by determining the optimal contact pressure on the active cell surface ● developed for high stress in the field of quality assurance and laboratory environment
-
Product
Cell Stand
CS-3A
-
The CS-3A Cell Stand is adopted with CHI series Electrochemical Analyzers and other apparatus directly. The cell is enclosed in a Faraday cage to reduce electrical interference. A built-in gas control allows purging a sample. Gas line is provided to purge next sample, while analyzing the present sample separately, thus increasing productivity. Magnetic stirrer allows for controlling the mixing of the sample for experiments requiring mass transport of electrolyte or analyte to the electrode surface. Cell top positioner with detachable cell cap allows easy removal and replacement of the cell vial as well as the electrodes for rinsing, cleaning, and replacement.
-
Product
Insulation Resistance Tester For PV (4 Range)
MIS-PV2
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
The model MIS-PV2 is an insulation resistance tester for the exclusive use in photovoltaic systems. The ordinary insulation resistance testers cannot make measurement properly during generation of PV systems. This instrument, however, can measure the insulation resistance simply by touching probe to the live line whether making generation or not. There are two ranges of PVH and PVL. PVH is for high voltage generation system (more than 500V and less than 1000V) and PVL is for the system less than 500V.
-
Product
Solar PV Test Equipment
-
The Seaward Solar range of electrical solar PV test equipment enables Photovoltaic installers to meet all testing and certification requirements of IEC 62446 safely and efficiently.
-
Product
Cell Testing
-
PEC offers a wide range of cell testers, starting from the 5A desktop test system (ACT0505), to our range of 50A cell testers for more standardized cycling (CT0550) and our advanced cell testers with capabilities up to 4000A (ACT0550). All systems support parallel switching for achieving higher currents.
-
Product
PV Test Solutions
-
High-speed and high-accuracy measurement of solar cell I-V characteristics in three modes
-
Product
PV Accelerating Tester
-
King Design Industrial Co., Ltd.
*Spectrum mis-match: IEC 60904-9 class A*Non-uniformity <5%*Instability <5% ( within 30 mins)*Irradiance range: 800 W/m2 ~ 1200W/m2*Effective range: 30cm x 30cm; 1.1m x 1.4m*(customize accepatble)*Temperature：40℃ ~ 90℃*Humidity: 20% ~ 85%
-
Product
Small Cells
-
5G small cells enable additional capacity and coverage to networks when and where needed – both indoors and outdoors. Our 5G protocol software for small cells supports both sub-6 GHz and mmWave bands and leverages the Small Cell Forum’s FAPI and nFAPI open interfaces to work seamlessly on our partners’ SoC-based small cell platforms.
-
Product
Load Cells
-
A load cell is a sensor which transforms the load or force applied to it into an electrical signal. Load cell sensors are based on the strain-gauge principle i.e. a sensor whose resistance varies with applied force. They are the most widely used as load transducers in all areas of weight measurement from retail scales, the process industry and medical applications.
-
Product
Voltammetry Cell
VC-4
-
Capable for measuring of 1 - 3 ml of sample volume using electrodes with 6 mm of the diameter. Furnished holder prevents the vial from spilling.
-
Product
Voltammetry Cell
SVC-2
-
SVC-2 Voltammetry cell can be used for 4 modes voltammetry cell setup. Each voltammetry cell has its specific feature. However, SVC-2 can be sed in 4 modes. Also can apply as an oxygen-free voltammetry cell.
-
Product
Canister Load Cells
-
PCB's cost-effective canister load cells are easy to install and ideal for low-capacity applications. Canister style load cells include a built-in mounting base for a simplified installation in both tension and compression applications.
-
Product
H-Type Electrolytic Cell
AH-2
-
Durable and corrosion-resistant acrylic electrolytic cell with excellent visibility. Compatible with 100ml–1200ml single or multi-chamber configurations. Ideal for electrochemical experiments requiring easy monitoring and maintenance.
-
-
Product
H-Type Electrolytic Cell
SHE-1
-
Dual-layer sealed H-type electrolytic cell with optical windows and water bath compatibility. Volume options from 50–300ml. PTFE caps and glass body included.
-
Product
Insulation Resistance Tester For PV (Judge Deterioration Point)
MIS-PVS
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
The model MIS-PVS is an insulation resistance tester for the exclusive use in photovoltaic systems. The ordinary insulation resistance testers cannot make measurement properly during generation of PV systems. This instrument, however, can measure the insulation resistance simply by touching probe to the live line whether making generation or not. There are two ranges of PVH and PVL. PVH is for high voltage generation system (more than 500V and less than 1000V) and PVL is for the system less than 500V.
-
Product
Mini Load Cells
-
Interface Mini™ load cells are designed for light touch, light weight, and compact applications. Our miniature load cells provide exceedingly accurate measurements similar to our LowProfile load cells that have our proprietary strain gages. All our miniature beam load cells, load buttons, load washers, rod end load cells, S-type load cells, and platform scale load cells can all be ordered in range of different sizes. Capacities are available as low as 0.11 lbf (0.5 N) and as high as 1,124K lbf (5,000kN). A variety of our miniature load cells are designed for off-the-shelf and OEM applications. Our engineers can also work with you to design custom load cells to fit your exact specifications and requirements.
-
Product
Stimulus Test Cell
HA7200
-
The HA7200 enables these improvements by providing high-speed, high-accuracy temperature and pressure test for automotive sensor R&D and production. Advantest’s proprietary temperature control technology delivers an optimized test solution for high-spec pressure sensors across a broad range of temperatures, in the automotive industry and beyond.
-
Product
Permeability Cells
Flexible Wall Permeameter
-
The Permeability Cells - Flexible Wall Permeameter for Soil Samples performs permeability tests on normal and contaminated soil samples. The permeability cells are available either in brass for normal use or in stainless steel for contaminated materials. Top caps and pedestals are available for normal or contaminated materials.
-
Product
Spectroelectrochemical Flow Cell
SEC-2F
-
Using the spectroelectrochemical flow cell, it is possible to have a different optical path length changing the gasket. We offer, as an optional item, a silicon and Teflon gasket with a 100, 250 and 500 m of the thickness. SEC-2F Spectroelectrochemical flow cell was designed to fit perfectly in the SEC2000 Spectrometer, and it eliminated the use of the optical fiber to connect the Spectrometer to the SEC-2F. Even for another brand of the spectrometer, you can connect the SEC-2F using the collimating lens and optical fiber.
-
Product
Battery Cell Tester
-
This Centre zero instruments help to read the voltage irrespective of polarity.
