-
product
Quad 4x32 Reed Matrix for 34980A
34934A
The Keysight 34934A module for the 34980A Multifunction Switch/Measure Unit offers the highest density matrix for connecting paths between your device under test and your test equipment, allowing for multiple instrument connections to multiple points on your device under test at the same time.
-
product
PCIe Mini Module
PCIe-Mini-COM-8
The PCIe-Mini-COM-8 is an 8-channel PCI Express (PCIe) UART (Universal Asynchronous Receiver and Transmitter) optimized for higher performance. The PCIe-Mini-COM-8 serves as a single lane PCIe bridge to 8 independent enhanced 16550 compatible UARTs.
-
product
PXI/PXIe Power Relay Module, 1xSP4T, 20 Amp
42-166-203
The 40/42-166-203 is a PXI/PXIe high density power relay module with 1xSP4T switches rated at 20A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations.
-
product
Mini PCI Module
MPCI-1553-DDC
The ALPHI MPCI-1553-DDC uses the BU-65864 communication device as its 1553 bus controller, or remote terminal, or monitor terminal. A single controller has two redundant channels and built in transceivers. The controller has internal transceivers for both channel A and B. The Mini PCI board has on-board transformers for both channels. The board format is a Mini PCI boardlayout.
-
product
VTAC, Patchcord, ITA, 36", VTAC, DACAR 535, to Rosenberger
7-141702731-036
The density/ thickness of DACAR 535 wire may require a module loading pattern that includes extra slot spacing to prevent wire bend and pressure. See the VTAC User Manual for more information.
-
product
25 Pin D-Type Cables - Connector to Connector for Pickering
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 25-pin D-type connector.
-
product
PXI Prototyping Module, 1-Slot, 96-Pin Micro-D
40-225A-101
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
Ultra-Low Frequency Raman Spectrometer Down to 10 cm-1
Modular TeraHertz Raman Spectrometer
HORIBA’s modular terahertz modular Raman spectrometer extends the spectral range of a measurement to < 10 cm-1. Consisting of an Ondax SureBlock™ module fiber coupled to HORIBA’s iHR320 imaging spectrometer, this custom system provides an affordable option for macro-Raman measurements close to the laser line. Below are Stokes and anti-Stokes spectra of elemental sulfur recorded with this system.
-
product
PXI/PXIe MEMS Optical Switch, Single Insert/Bypass, Multi-Mode, 62.5/125 Fiber
40-860A-212-M-HI
The 40/42-860A-212-M-HI is a PXI/PXIe single insert/bypass switch with SC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
ATCA Rear Transition Module
ART132
The ART132 is an I/O expansion ATCA Rear Transition Module(ARTM) that provides PCIe, GbE, InfiniBand, USB andManagement I/O for the front blade. The module is designed tomate with Emerson front blades such as ATCA-7360 andATCA-7365.
-
product
cRIO-9041, 1.30 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Kintex-7 70T FPGA, 4-Slot CompactRIO Controller
786369-01
1.30 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Kintex-7 70T FPGA, 4-Slot CompactRIO Controller - The cRIO-9041 is a rugged, high-performance, customizable embedded controller that offers Intel Atom dual-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 70T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and determinis...show more -
product
Compact Transmitter Module
AMC-I
Virginia Diodes'' Signal Generator Extension Modules (SGXs) provide high performance frequency extension of microwave signal generators into the THz range. VDI now offers integrated Amplifier / Multiplier Chains that provide industry leading performance in a compact package.
-
product
PXI/PXIe High Density Precision Resistor Module, 6-Channel
40-297A-051
The 40-297A-051 (PXI) and the 42-297A-051 (PXIe) are 6-channel programmable resistors with a range of 3 Ω to 2.97 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI 8 Slot BRIC 264x8 2-pole (12 sub-cards)
40-562A-122-264X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI 32 Channel I/O Serial I/P Prog Threshold
40-412-001
The 40-412 is a 32-channel Digital I/O module with high output voltage and current capability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low using a high current capacity drive capable of sourcing 0.4A from the high side or 0.5A sink on the low side for each channel. The module is available in two versions with either serial or parallel capture of the input levels
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-014
The 40-297A-014 (PXI) and the 42-297A-014 (PXIe) are 18-channel programmable resistors with a range of 1 Ω to 470 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
Calibration Lead - Precision Resistor Modules
40-975-037-02-1m
The cable assembly is specifically designed to connect to the 37-Pin D-Type calibration port located on the front panel of Pickering Interfaces Precision Programmable Resistor Modules 40-293 and 50-293 enabling calibration via an external DMM.
-
product
3U CPCI Dual IP Carrier
CPCI-SIP
The CPCI-SIP module provides a 3U high performance flexible I/O scheme that supports industry standard Industry. PacksÔ. For application requiring low cost, high density I/O or unique combinations, the CPCI-SIP is the perfect solution. The CPCI-SIP is also available with the Industry Pack lines routed to the CompactPCI P2 connector for application that require rear panel I/O.
-
product
sbRIO-9215, Non-Enclosed, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
781029-01
Non-Enclosed, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The sbRIO‑9215 performs differential analog input. The sbRIO‑9215 contains NIST‑traceable calibration, a channel‑to‑earth ground double isolation barrier for safety and noise immunity, and high common-mode voltage range. Non-enclosed modules are designed for OEM applications.
-
product
TB-2630B , Screw Terminal, Ribbon, PXI Module Multiplexer Terminal Block
781687-01
The TB-2630B provides the necessary routing to configure the PXI-2630B PXI Multiplexer Switch Module as a single, dual, or quad 1-, 2, or 4-wire multiplexer. You can directly connect the TB-2630B to the front panel I/O connectors of the PXI-2630B. The NI TB-2630B features ribbon cable headers to connect signals to the PXI Multiplexer Switch Module as well as screw terminals for trigger input and trigger output signals.
-
product
USB DAQ
ADLINK USB DAQ modules leverage the expertise of ADLINK's analog design capability, enhancing convenience of data acquisition. Simply plug the ADLINK USB DAQ into a USB port on your computer or notebook for performance equaling or even exceeding that of ADLINK PCI/PCIe DAQ cards, with no need to power down or open the chassis. As well as providing basic voltage measurement, ADLINK USB DAQ modules feature built-in signal conditioning to directly receive measurement from most commonly used sensors...show more -
product
Ensenso 3D Cameras
X Series
Imaging Development Systems GmbH
The Ensenso X series is a modular and ultraflexible 3D camera system. The projector module with 100 W LED projector power is equipped with an integrated Gigabit Ethernet switch and can be combined with selected GigE uEye camera models to a customised 3D camera system.
-
product
Functional Testing
Interface Testingevaluation of correct system module interaction Smoke Testinginitial testing process to check whether software is ready for further testingSystem Testingconducted on a complete, integrated system to evaluate the system's compliance with its specified requirements Integration Testingperformed to test units of code to verify interaction between various software components and detect interface defectsRegression Testingtesting to ensure changes made are not impacting previously working functionality Acceptance Testingperformed to make sure the software handles required tasks in real-world scenarios, according to specifications
-
product
COM Express Mini Size Type 10 Module with Intel Atom® E3900 Series, Pentium®, and Celeron® SoC (formerly Apollo Lake)
nanoX-AL
The nanoX-AL is a COM Express® COM.0 R3.0 Type 10 module supporting Intel Atom® processor E3900 series system-on-chip (SoC). The nanoX-AL is specifically designed for customers who need optmized processing and graphics performance with low power consumption in a long product life solution.
-
product
Filtered DC Interface Module
DC modules for RF Test Enclosures eliminate conducted and radiated interference, while providing a source of DC power.
-
product
PXI 4 Slot BRIC 32x12 2A 1-Pole Matrix
40-597-001
The 40-597 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 100VDC/70VAC. The 40-597 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
product
Loudness Monitoring
The Actus Loudness module lets operators maintain continuous measurements, which among other things, identifies program loudness and loudness range. Loudness measurements combined with robust logging allow users to quickly review the status and provide continuous, exportable measurements as proof of compliance and to defend against loudness complaints.
-
product
Amplifiers
Amplifier is designed to be used in conjunction with optional modules and can be confiugured for up to 8 inputs and 8 outputs. 9000 series modules as well as existing 900 series input modules can be used. The more appropriate modules can be selected depending on applications. Since it comes with two 60W power amplifiers, it can individually perform multi-origin braodcasts. It is equipped with singnal processing and control functions necessary for sound reinforcement, permitting all parameters to be set at the mixer. Settings data can be stored inside the unit and called up using the keys on the front panel.
-
product
Safety Certified I/O Modules
HY-TTC 30XSH
HY-TTC 30XSH, a member of the HY-TTC 30X family, is certified by TÜV Nord according to the EN 13849 standard and fulfills Performance Level c (PL c) requirements. Just as the other family members this certified unit must be used in combination with a master module. For safe communication the standardized CANopen Safety protocol is applicable since compliance to the European standard EN 50325-5 for CANopen Safety is provided.
-
product
PXI 2.5W Programmable Resistor Module, 1-Channel, 2.5Ω to 773kΩ
40-251-143
The 40-251-143 is a programmable resistor module with 1 channel which can be set between 2.5Ω and 773kΩ with 1Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.