Emulator Adapters
-
Product
RF Adapters
RP-SMA Adapters
-
Are semi-precision units that provide excellent electrical performance from DC to 34 GHz and outstanding mechanical durability.
-
Product
Basic Protocol Multi-Terminal Emulation
Sy629PMC-BPT
-
The Sy629PMC-BPT card provides a convenient means for transmitting and receiving data over an ARINC 629 bus in accordance with the transmit and receive programme defined by data written into the XPP and RPP memory. In particular, this product can emulate up to 120 terminals transmitting on an ARINC-629 data bus whilst correctly maintaining the Basic Protocol.
-
-
-
Product
Supply Adapters
AP Series
-
*Overflow Relative Noise Temperature and Return Loss Measurement within all Frequency Range*Ultrawide Frequency Range*Small Size*4 Design Structures with Different Connector Types
-
-
Product
Network Emulation
-
PacketStorm Communications, Inc.
The PacketStorm IP Network Emulators and simulators reproduce the unfavorable conditions of IP Networks and WANs in a controllable and repeatable lab setting. PacketStorm is the Industry leader of Layer 2 and Layer 3 WAN emulation and network bandwidth simulation.
-
Product
EBIRST 200-pin LFH To 96-pin SCSI Adapter Cable
93-002-226
Test Adapter
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
VoIP Adapter
-
A VoIP adapter is a protocol converter (bridge) between analog phones and the digital (IP) network that carries voice calls.
-
-
Product
Car-to-X Signal Strength Emulator
-
Qosmotec Software Solutions GmbH
QPER-C2X is a special adaptation of the signal strength emulator QPER, designed for mobile and Vehicular Ad-hoc Networks (MANet and VANet). Every radio devices in such an infrastructure-less network acts as a sender, receiver, and forwarder (router). Therefore, the ports of the QPER-C2X hardware are fully connected with each other by dynamically controllable attenuators. The system is fully designed for frequencies up to 6 GHz, since wireless communication for Intelligent Transport Systems (ITS) is based on the WLAN standard IEE 802.11p from 5.850 MHz to 5.925 MHz. The connected ITS stations can be either on-board units, as they are built into cars, or road side units that are used by road infrastructure (traffic lights, road work area delimiters, velocity signs). For tests in the lab, radio modules of such ITS stations are each kept in a shielding box that prevents any unwanted radiation over the air.
-
-
Product
Coaxial Waveguide Adapter, APC-7, 12.4 to 18 GHz
P281B
Coax Adapter
The Keysight P281B adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Maxi Relay Adapter
190-8
-
The relay in question is a popular 50 Amp relay used on heavy duty, equipment, automotive branch circuits and other higher current applications. The Maxi relay has two large legs and two smaller legs on it,
-
Product
Coaxial Adapter, 3.5 mm (m) to 3.5 mm (f), DC to 26.5 GHz
83059C
Contact Adapter (Receiver)
The Keysight 83059C instrument-grade 3.5-mm coaxial adapter offers outstanding performance to 26.5 GHz. With SWR typically better than 1.05, this adapter is ideal for most connector saver and interconnect needs.
-
Product
Waveguide to Coaxial Adapter
D8-AWC84SK-1296
-
Waveguide to Coaxial Adapter, Frequency 6570~9990MHz, 50W, Rect. Waveguide FBP84, SMA Female
-
Product
Probe Adapters
-
Probe adapters provide simple and easy interface of third-party probes as well as change between the different Teledyne LeCroy Oscilloscope input and cable types (ProBus, ProLink, K/2.92 mm, BNC and SMA). Depending on the adapters, changing between the Teledyne LeCroy Oscilloscope's input type may have an effect on the overall performance of the channel.
-
Product
In-Circuit Emulator
DS-XA
-
* Emulates XA Derivatives * 2MByte Code and Data Memory * Memory With Mapping Capabilities * Real-Time Trace * Frequency Range up to 30MHz @ 5V * Source-Level Debugger For C And Assembler * MS-Windows Debugger Software for Windows NT and 95 or Later * 3.3V And 5V Emulation Support * Support for ROMless and ROM Microcontrollers * PLCC Emulation headers
-
Product
PoE LLDP Emulation (PD) & Analysis for 802.3at & 802.3bt
802.3at and 802.3bt PD Emulation and Protocol Analysis
-
Integrated PoE LLDP and Load Emulation in a Single Instrument. IEEE 802.3at and 802.3bt LLDP Compliance Analysis. Independent, Per-Port 802.3at and 802.3bt LLDP Emulations. Flexible Single and Dual Signature PD LLDP Emulations. One-Click LLDP Protocol Capture and Analysis. Pop-Up Excel Spreadsheet Reports Assess Protocol Content and Timing. Enables One-Click Emulated Power-Ups and Standard Waveforms with LLDP Power Granting PSE's. Enables 2-Pair and 4-Pair PSE Conformance Test Suties with LLDP Capable PSE's. Enables 2-Pair Multi-Port Suite with LLDP Capable PSE's. Available for PSA-3000 and PSL-3000 Platforms.
-
-
Product
Special Adapters
-
There are use cases when the debug tool doesn’t connect to the embedded target through an architecture standardized and widely used connection. Special Adapters are available to connect the iC5700 BlueBox to the embedded target system in such environments.
-
Product
JESD22-A115 Machine-Model (MM) Pulse Emulator
MM-10A
-
High Power Pulse Instruments GmbH
- Pulse unit to generate JESD22-A115 machine-model (MM) waveforms with TLP- Extremely stable and reproducible machine-model (MM) waveforms- Compatible with HPPI TLP-3010C/4010C/8010A/8010Csystems which have installed pulse width of 25 ns and rise time of 100 ps to 300 ps- Up to ±10 A machine-model peak current with TLP-3010C, which is equivalent to ±667 V (MM)- Up to ±15 A machine-model peak current with TLP-4010C, which is equivalent to ±1000 V (MM)- Up to ±30 A machine-model peak current with TLP-8010A and TLP-8010C, which is equivalent to ±2000 V (MM)- Same measurement procedure as TLP including DC test of the DUT- Compatible with HPPI TLP software and waveform data storage and management- 50 Ω SMA input and output connectors- Compact size: 61 mm x 25 mm x 17 mm
-
Product
Local DVB-T2 Adapter
T2 Edge DTH
-
T2Edge DTH is ENENSYS local DVB-T2 adapter of the OneBeam DVB-T2 solution. Running on the transmission site prior to the DVB-T2 transmitter, the T2Edge DTH aims at receiving a DTH stream to build a new DVB-T2 multiplex. It selects the services from the DTH stream and generates a T2-MI stream. The T2EdgeDTH performs an advanced PSI/SI processing to update PSI/SI information related to the filtered services.
-
Product
Manual Test Adapters
-
Manual test adapters (MA) from INGUN are available in several series and series, which differ in terms of use, maximum permitted contact force, parallel stroke, size and service life.
-
Product
RF Adapters
BNC Adapters
-
Amphenol RF offers a wide array of both in-series and between-series BNC adapters in straight and right-angle configurations. 50-ohm and 75-ohm impedance BNC adapters are available with and without panel mounting features. Popular mounting features in bulkhead, both front and rear mount, and 4-hole flange designs. 50-ohm BNC connectors have a frequency range from DC to 4 GHz. 75-ohm BNC connectors optimized for 4K/UHD video applications can perform well to 12 GHz.
-
Product
WAN Adapters
FarSync T2Ee
-
The FarSync T2Ee PCIe card provides high performance 2 port low profile synchronous communications with multiple signalling modes for Linux and Windows systems.
-
Product
Host emulator
E84
-
Precision Development Consulting Inc
A USB controlled and self-powered emulator for functional testing SEMI E84 implementations. (E84-1000) This was developed because there was nothing like it in the marketplace, and it was clearly needed. This product enables a factory automation engineer to perform E84 functional testing anywhere in the world. Weighing less than 5oz, it is neither a burden, nor a power hog. You will never need to look for an additional power receptacle in the fab. The emulator gives the user full control over the sequence so that any test can be performed. Existing products were large and unwieldy, and provided canned tests that could not be modified to meet the requirements that Fab managers impose on their suppliers.
-
Product
PCI to PC/104+ Bus Adapter
327/328
-
Model 327 and 328 are bus-to-bus adapters that allow operating a PCI board from a PC/104+ card stack. They allow selection of important PC/104+ signals using jumper plugs, thereby avoiding the requirement of using hardwired settings. Model 327 aligns the PCI board parallel to the PC/104+ boards, while model 328 places it perpendicular.
-
Product
Test Adapter
-
Development of a 12-way test and programming adapter from Toptest for ?? The Dash ?? from Bragi, a wireless, intelligent earphone with communication and sensor technology. With the first version of the test adapter, only a purely sequential testing was possible due to the interdependencies of the tests. In version 3.0, the now autonomous tests were brought into a parallel TestStand sequence. In addition, individual sockets were prioritized in order to optimally use the hardware resources. This resulted in a time advantage of 80% compared to the initial situation.
-
