Emulator Adapters
-
Product
Pulse Adapter
CV30P650
-
Frothingham Electronics Corporation
The CV30 P650 test station is currently the highest voltage pulser in a series of exponential pulse generators that can be connected to our FEC200E tester. This gives you all the versatility of the proven FEC200 with the addition of high power exponential pulses. The CV30 P650 pulse adapter can produce a maximum current of 100A at up to 600V using exponential pulses up the 10/1000 waveform. The pulser is rated at 30KW from 300V to 650V. Voltage compliance at 100A is 600V. The station can also include all of the usual FEC200 tests in the same test program.
-
Product
NI-5733, 120 MS/s, 16-Bit, 2-Channel Digitizer Adapter Module for FlexRIO
781659-02
Digitizer
The NI‑5733 is a digitizer adapter module that, when combined with a PXI FPGA Module or Controller for FlexRIO, creates a high-speed digitizer that simultaneously samples two channels at 120 MS/s. You can use the NI‑5733 to do real-time processing and streaming of analog data with high-performance A/D converters. The NI‑5733 also includes selectable elliptic, Bessel, and bypass hardware filters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.
-
Product
Signal Generator Adapter Module For FlexRIO
Signal Generator
Signal Generator Adapter Modules for FlexRIO feature either high or low‐speed analog output and can be paired with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO for custom signal generation. Whether you need to dynamically generate waveforms on the FPGA or stream them across the PXI backplane, these adapter modules are well suited for applications in communications, hardware‐in‐the‐loop (HIL) test, and scientific instrumentation.
-
Product
X.25 Adapters & XOT
FarSync X25 T2Ee
-
The FarSync X25 T2Ee PCIe card provides a very flexible 2 port PCI Express low profile X.25 communications platform for Linux and Windows systems
-
Product
Adapter for 980L-1A Tester
TA-331A
-
331A-9G HSI Adapter for use with the 980L-1A tester. Built to manufacturer's specs to allow by the book testing.
-
Product
RF Adapters
SMA Adapters
-
Are semi-precision coaxial RF connectors developed in the 1960s as a minimal connector interface for coaxial cable with a screw-type coupling mechanism.
-
Product
Low-Profile PCI-to-CardBus/PCMCIA/PC-Card Adapter, 1 Rear Slot, Universal
P311
-
This product is recommended for Systems Integrators and OEMs only due to the non-standard "volume envelope" that is required around the host's PCI connector.
-
Product
2.92mm to ProLink Adapter with Probe Power and Communication Pass Through
L2.92A-PLINK
-
The Teledyne LeCroy LabMaster 10 Zi oscilloscope utilizes precision 2.92mm input connectors to achieve up to 36GHz of input bandwidth. But some applications may require the use of lower-bandwidth probes for performance and cost reasons.The L2.92A-PLINK adapter converts the 2.92mm interface to a ProLink interface. This brings the benefits of a wider selection of probes to the LabMaster 10 Zi such as Dx10/Dx20/Dx00A-AT 4-6 GHz differential probes and DH Series 8 to 20 GHz differential probes using the ProLink oscilloscope probe connection. Full probe power and control is provided through a built-in LEMO interface.
-
Product
Adapter & DC Block
-
RF Lambda’s DC blocks are used to prevent DC signals from passing through a coaxial RF interface. They are low IL and wideband. RF Lambda’s line of adapters are used to connect RF signals using different connector options.
-
Product
cPCI to PMC Adapter / Carrier
cPCI2PMC
-
The cPCI2PMC ( cPCI to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard cPCI slot. The cPCI2PMC has a PMC card slot mounted to a universal 3U 4HP cPCI card. Suitable for 32/64 with 33/ 66 MHz bus operation. The PMC user IO connector Pn4 is optionally connected to J2 for rear panel IO.
-
-
Product
2.92mm to ProBus Probe Adapter
L2.92A-PBUS
-
The Teledyne LeCroy LabMaster 10 Zi oscilloscope utilizes precision 2.92mm input connectors to achieve up to 36GHz of input bandwidth. But some applications may require the use of lower-bandwidth probes for performance and cost reasons.The L2.92A-PBUS adapter converts the 2.92mm interface to a ProBus interface. This brings the benefits of a wider selection of probes to the LabMaster 10 Zi from high-impedance ZS active probes to the high-bandwidth WaveLink differential probing system. Full probe power and control is provided through a built-in LEMO interface.
-
Product
Adapter, 2.4 mm (m) to Type-N (m), DC to 18 GHz
11903A
-
The Keysight 11903A is a metrology-grade, 2.4 mm male to type-N male adapter with dc to 18 GHz operation.
-
Product
Test adapter LRM-LR (Type F)
MA-LML01D
-
Hachmann Innovative Elektronik
Our test adapter MA-LML01F connects LR measuring devices to standardized LRM string parts. Due to small dimensions and skid-proof design it's easy for him to catch up with everything.
-
-
Product
Emulation
-
Synopsys ZeBu® emulation system delivers the performance needed to make verification teams and software developers working on the most advanced chips successful. ZeBu emulation systems are modular, allowing users to deploy the capacity needed in a scalable and easily extensible fashion.
-
Product
Electric Vehicle Charging Station EVSE Test Adapter
FEV100
-
Test the safety and performance of a type 1, level 1 or level 2 electric vehicle ac charging stations (EVSEs) with the Fluke FEV100. This test adapter simulates the presence of an electrical vehicle, allowing you to conduct tests in combination with appropriate test instruments such as a digital multimeter or oscilloscope.
-
Product
ROM Emulator Instrumentation
-
High-speed and static 3U and 6U PXI and PCI digital I/O instrumentation. Offering test rates to 200 MHz and programmable logic levels of -10 V to +15 V, our digital products feature the highest performance and most cost effective digital test solutions in the industry.
-
Product
Coaxial Waveguide Adapter, 2.4 mm (m), 26.5 to 50 GHz
R281B
-
The Keysight R281B adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Passive XMC-to-PCI Express Adapter
6066
-
Our Passive XMC-to-PCI Express Adapter +5VPWR 4X (6066) is designed to adapt a single-wide XMC card to a 4X PCI Express slot. The 6067 supports P15 only and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card.
-
Product
Mobile Comm DC Source w/ Battery Emulation, DVM
66321D
Battery Simulator
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.The Keysight 66321D mobile communications dc source provides fast transient response, exceptional sourcing, output resistance programming, and precision measurement. This product is specially designed for testing next generation digital wireless communications products. The 66321D mobile communications dc source offers a new capability that simulates the internal resistance of a battery or battery pack. Additionally, these high performance models offer improved transient response and stable output operation with either short or long load leads. The 66321D dc source provides all of the capabilities of the 66321B with the addition of a built-in digital voltmeter.
-
Product
PMC-to-PCI Express Adapter (PCIe/PCI-e)
5243
-
Our PMC-to-PCI Express Adapter (PCIe/PCI-e) 1X (5243) permits the use of a single-wide PMC module in a 1x PCIe slot. The A and C rows of a 96-pin DIN connector, located toward the rear of the board, connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card.
-
Product
PCI-to-CardBus/PCMCIA/PC-Card Adapter, 1-slot, Texas Instruments PCI1410 Chipset
P111
-
The P111 is perfect for use with Wireless LAN cards like WiFi / 802.11b or any of the newly emerging 802.11a or 802.11g standards. It also suits Bluetooth cards or other functions where the ability to occasionally remove the card is important, but where during normal use the rear facing aspect of the slot suits its operation.
-
Product
Test Adapter
PMC-UNIV-TEST
-
PCI adapter for PMC with options for PCI and PMC Stack Pass through connections
-
Product
Tool, Extraction, 90 Series Modules, Interconnect Adapters
910109111
Extraction Tool
Tool, Extraction, 90 Series Modules, Interconnect Adapters
-
Product
Chip Test Adapter
RAMCHECK Sync
-
The RAMCHECK Sync Chip Adapter tests popular TSOP SDRAM memory chips in sizes of 16Mx16, 4Mx16, 32Mx8, 8Mx8, 64Mx4, 16Mx4 and more. Picture above shows the adapter with all optional sockets for 54, 50 and 44-pin.
-
Product
Regenerative AC Emulator, 600 VAC, 63 A, 30 KVA, 3‑Phase
SL1201A
-
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
Attenuator Interconnect Kit, 3.5 mm
11716E
Interconnect Adapter
The 11716E attenuator interconnection kit provides the necessary parts to connect 84904K and 84906K programmable step attenuators in series.
-
Product
Package Converters & Fix Adapters
-
Package converters provide an electrical and mechanical conversion from one package type to another. We use gold plated interconnects for our pin and through hole converters. Ironwood Electronics offers solder column adapters as a solution for leaded SMT packages such as QFP, PLCC, SOIC, SSOP, and TSOP. This is an excellent choice when you have a PC board in production that needs an upgrade or you need to replace an obsolete part.
-
