Showing results: 3436 - 3450 of 3728 items found.
-
785264-01 -
NI
The USRP-2955 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless receiver systems. It is designed for over-the-air signal acquisition and analysis. It features a two-stage superheterodyne architecture with four independent receiver channels and shares local oscillators for phase-coherent operation. It also offers a Kintex-7 FPGA programmable with the LabVIEW FPGA Module. With these features, the USRP-2955 has the RF and processing performance for applications such as spectrum monitoring, direction finding, signals intelligence, wideband recording, and radar prototyping. The USRP-2955 is equipped with a GPS-disciplined 10 MHz oven-controlled crystal oscillator (OCXO) Reference Clock, which improves frequency accuracy and synchronization.
-
785263-01 -
NI
10 MHz to 6 GHz, 80 MHz Bandwidth, Reconfigurable USRP Software Defined Radio Device - The USRP-2945 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless receiver systems. This software defined radio reconfigurable device is designed for over-the-air signal acquisition and analysis. It features a two-stage superheterodyne architecture with four independent receiver channels and shares local oscillators for phase-coherent operation. It also offers a Kintex-7 FPGA programmable with the LabVIEW FPGA Module. With these features, the USRP-2945 has the RF and processing performance for applications including spectrum monitoring, direction finding, signals intelligence, wideband recording, and radar prototyping.
-
Model N300M -
Teledyne Advanced Pollution Instrumentation
The Model N300M is a microprocessor-controlled analyzer used to determine the concentration of carbon monoxide (CO) in a sample gas. The analysis method is based on the Beer-Lambert law.The N300M uses Gas Filter Correlation (GFC) to overcome the interfering effects of various other gases (such as water vapor) that also absorb IR. The analyzer passes the IR beam through a spinning wheel made up of two separate chambers: one containing a high concentration of CO known as the reference, and the other containing a neutral gas known as the measure. The concentration of CO in the sample chamber is computed by taking the ratio of the instantaneous measure and reference values and then compensating the ratio for sample temperature and pressure.
-
ULP-27 -
Unitech Scales And Measurements Pvt. Ltd
Unitech’s Temperature Control Loop Setup is basically a PC based PID controller setup used for closed loop and open loop analysis of temperature process system. The setup comprises of RTD temperature Sensor. The water flows through the Rotameter and Process tank to which a heating coil is fitted. The heater is controlled by a Thirstier drive. The Thirstier drive is connected to PID controller. The manual control valve can control the water flow. The system is mounted on a tabletop model with all necessary Piping. Water at approx. 100 LPH has to be supplied to a system externally. The electronic panel comprises of ADC/DAC card with RS-232 interfaces.
-
Prometheus -
Dishtronix Inc.
The design of the Prometheus is the result of over 10,000 hours of research and development, encompassing hundreds of hours of mathematical analysis, computer simulation and modeling, and numerous prototypes and experiments spanning over a five year period. The result is a rugged, commercial quality amplifier designed to run cool under 1500W continuous SSB, CW or RTTY, with special ferrite transformers and combiners designed for full power operation even on 160 meters. Although our custom transformers are more expensive and difficult to manufacture than competing designs, they do not saturate or heat up beyond the Curie point, thereby becoming irreversibly damaged and destroying the RF transistors in the process.
-
Accsense, Inc
Accsense Electrocorder Data Loggers are electrical logging devices monitoring power/energy, current/voltage, power quality and more. These products perform ongoing datalogging to identify issues with supply and equipment; to calculate and prove the value of future energy savings; and as low-cost investments for long-term energy savings. Electrocorder constantly samples every cycle multiple times (recording the Min, Max and Average) over the set period. Additionally, specialized Electrosoft software is included FREE with every unit to assist with data interpretation, enabling users to define the voltage to plot power and energy, then simply upload their recorded data via USB to a PC for analysis.
-
PCB Piezotronics, Inc.
In-line ICP® charge converters play a vital role in converting high impedance charge mode piezoelectric sensor signals into low impedance voltage signals, facilitating input to readout, recording, and analysis instruments. Specifically engineered for compatibility with high temperature piezoelectric sensors, these units are capable of operation in environments reaching up to 500°F (260°C). The series boasts ±2.5V or ±5.0 V output, offering a range of gain options, all packaged within a compact and durable casing. As a cost-effective alternative to laboratory charge amplifiers, in-line ICP® charge converters present an appealing choice for multi-channel applications.
-
Siama Systems, Inc.
GENEM-C is a high-capacity network infrastructure testing software application for network equipment manufacturers, data centers, service provider telco cloud and 5G backhaul. It runs on the PROVA-C hardware appliance that is built on BittWare. GENEM-C allows you to verify, monitor and troubleshoot Ethernet/IP network equipment and data center applications to ensure network services can accommodate the demands of your customers. Ideal for QA test, Service Providers migrating to a DevOps model can use GENEM to validate service turn-up and modifications in the production network. GENEM is equally at home in a lab environment. It bundles wire-rate traffic generation and analysis capabilities with a network emulator and packet capture/replay function in a single software license.
-
GENEM-X -
Siama Systems, Inc.
GENEM-X is a high-capacity network infrastructure testing software application for network equipment manufacturers, data centers, service provider telco cloud and 5G backhaul. It runs on Siama’s carrier-class PROVA-X hardware appliance. GENEM-X allows you to verify, monitor and troubleshoot Ethernet/IP network equipment and data center applications to ensure network services can accommodate the demands of your customers. Ideal for QA test, Service Providers migrating to a DevOps model can use GENEM to validate service turn-up and modifications in the production network. GENEM is equally at home in a lab environment. It bundles wire-rate traffic generation and analysis capabilities with a network emulator and packet capture/replay function in a single software license.
-
PGA-710B -
Eurostat Group
A unique electrostatic data analysis device for use with Prostat’s PFK-100 Field meter/Charge Plate Monitor Set.• Records, plots, analyzes and automatically constructs reports of body voltage generation, electrostatic decay, voltageretention, ionizer performance and other static measuring functions.• Creates detailed reports to help determine the risk of equaling or exceeding damaging or hazardous HBM dischargevoltages in static sensitive facilities.• Analyze Footwear & Flooring Combinations: Records personnel walking voltages in accordance with ANSI/ESD STM97.2 Body Voltage measurements as required by ANSI/ESD S 20.20 ESD Program Standard• Other Equipment Applications include voltage generation of chairs, carts and process equipment
-
Teledyne LeCroy
Gen-Z is a data-access technology designed to provide high-speed, low-latency, memory-semantic access to data and devices via direct-attached, switched or fabric topologies. Gen-Z components use low-latency read and write operations to directly access data and use a variety of advanced operations to move data with minimal application or processor involvement. Gen-Z fabric utilizes memory-semantic communications to move data between memories on different components with minimal overhead. Memory-semantic communications are extremely efficient and simple, which is critical to delivering optimal performance and power consumption. Teledyne LeCroy provides protocol analysis and error injection test equipment to support development and debug of Gen-Z based devices
-
Salicon Nano Technology
Digital Signal Processing is a technique that converts signals from real world sources (usually in analog form) into digital data that can then be analyzed. Analysis is performed in digital form because once a signal has been reduced to numbers; its components can be isolated, analyzed and rearranged more easily than in analog form. Digital Signal Processing (DSP) applications are becoming more prevalent in everyday use. Because of this widespread usage and advances in computer technology, the DSP algorithms themselves are being subjected to more demanding specifications. There is a constant need for designing systems with lower power, higher speed and less space and to achieve this we are developing new algorithms, techniques.
-
CP-5110B Detector/CA-6000B Amplifier -
Ono Sokki
CP / CA series are systems that detect the rotation angle of the engine crankshaft composed of CP-5110B Fiber Optic Crank Angle Detector, CA-6000B Crank Angle Amplifier and CP-5120 / 5130 Slit disk.CP-5110B Fiber Optic Crank Angle Detector makes it possible to detect the crank angle required for various engine performance tests such as combustion analysis with high accuracy and high response. As it has a light projecting and receiving method with an optical fiber, it provides outstanding vibration and noise resistance without a built-in electric circuit in the detector.CA-6000B Crank Angle Amplifier inputs a signal of crank angle detector and outputs a TTL level angle signal and a 1P / R pulse signal.
-
SoundCheck -
Listen Inc
The SoundCheck®system from Listen includes everything you need to perform audio measurements on a wide range of devices – the software, the audio interface, other test interfaces and accessories, and test sequences. The system is centered around the SoundCheck software. This powerful package controls and communicates with the measurement hardware, and includes all the stimuli, algorithms and analysis functionality needed to develop and run virtually any electroacoustic or audio electronic test. It is paired with hardware ranging from a simple, all-in one audio test box to sophisticated discrete components for a complete test system. In addition to Listen hardware, a range of 3rd party products and test accessories are fully supported within SoundCheck.
-
Panasonic Industrial Devices Sales Company of America
Based on a rigorous analysis of embedded device software and system needs, the Panasonic AM1 (MN101C/MN101E/MN101L) and AM3 (MN103H/MN103S/ MN103L) Series signal a new concept in Microcomputer design. With 8-bit and 32-bit models that share a unified architecture, Panasonic Microcomputers combine high performance with low power consumption in a package that supports C-language programming for a fast, efficient development cycle. Since the instructions for MN103H/MN103S and MN101C/MN101E are respectively compatible with MN103L's and MN101L's, the programming data can be inherited to achieve efficient system development. Panasonic Microcomputers feature a single development environment and are suitable for a wide range of applications, including high-performance embedded controllers and key devices in multimedia hardware.
