- Pickering Interfaces Inc.
product
Switching System Test Tools
eBIRST
The eBIRST toolset consists of three different tools that support 200-pin LFH, 78-pin and 50-pin connectors and a set of adaptors that allow connection to other connector types. A supplied application program controls the eBIRST tools via a USB2 port that also provides the tool power and controls the switching system using a Test Definition File to define the test sequence. These tools work by measuring the path resistance at the switching system external connectors using four-wire measurements, quickly establishing whether the path is good, has increased resistance or has failed. Below are links to various eBIRST tool information:
-
product
Printed Circuit Board Testing Solutions
IES Systems is a turnkey test systems solution provider with 10 years of proven experience in printed circuit board testing solutions. Our experienced engineers design electro/mechanical solutions to interface between your product and our custom designed test instrumentation. We provide a complete solution to your PC board testing needs.
-
product
Analog Mixed Signal Testers
- PC-performance independent: multiple SPEA CPUs provide test program timing, while pc replacement does not require the test program requalification- Pattern-based programming: -30% test time vs competitors- 64-line synchrobus and 16-line high-speed synchrobus for real-time instrument synchronization: no embedded delay when running pattern-based testing- 99% parallel test efficiency- Multi-site test capabilities for up to 256 devices in parallel- High-density, floating instruments, for true parallel analog test- Universal slot architecture, up to 1,408 channels- RF generators up to 3 GHz
-
product
Rebound Hammer
SilverSchmidt - PCN
Concrete test hammer SilverSchmidt Type PC N : *Standard impact energy (2.207 Nm) with PC communication, increased memory capacity and Hammerlink software*Use for concrete >10cm*Measuring range: 10-100N/mm2
-
product
Board Test Adaptor (BTA)
MS 1104
BTA is used to test and validate TARANG (RWR) boards. The BTA has PC interface through RS232 / USB communication port. GUI based Test Software is used to test the UUTs and displays the result.
-
product
VGA and S-VGA test generator
TELETEST PC
A pocket sized, battery powered PC monitor test pattern generator. For fault finding and repairing PC systems with stand alone monitors.
-
product
Industrial USB 3.0 Tester
M5615B
International Microsystems Inc.
The M5615 tester is a 16 Socket Bench top Production and Engineering Tester that supports USB 3.0 Super Speed and USB 2.0 High Speed devices. The tester comes with a built-in PC running a full Linux operating system that tests and copies any USB storage device including USB Hard Drives at super speeds.
-
product
Micro-Ohmmeters
RMO-G Series
The RMO-G is a portable micro-ohmmeter designed for contact resistance measurement of non-inductive test objects and applications with increased safety requirement. It tests medium and high-voltage circuit breakers, disconnecting switches, high-current bus bar joints, cable splices, and different high-current links. Due to its Both Sides Grounded and Remote Control functionalities, the instrument accurately measures even in the most demanding environments, providing additional safety to testing ...show more -
product
PC Based Test Setup for Electric Iron Testing
SCR ELEKTRONIKS make PC Based Test Setup for Electric Iron Testing is useful to carry out various tests mentioned in IS 366:1991 clauses 10,11,12,13 & 14 on the Iron under test.
-
product
Servo-Pneumatic Asphalt Testing System
All signal conditioning, as well as high-speed data acquisition and control functions are done by the unit and graphically interfaced through CATS, windows based software running on a standard PC. The system is capable of performing the full spectrum of HMA tests: dynamic complex modulus, flow number, flow time, indirect tension, beam flexural fatigue and resilient modulus. These tests are done with the appropriate testing modules. The different testing modules can be obtained after the initial system acquisition at the same discounted price. In addition, guarantees system upgrades in order to meet future standards .
-
product
CD/DVD Analyzer
Shuttleplex
The ShuttlePlex CDVD Analyzer can be configured to automatically test, save, report, grade, print and export your optical disc data. The unit is designed to provide an efficient, effective, low cost analysis for just about any optical disc production process. The User interface provides a feature set and graphical environment (See Below) similar to those used by Professional Engineers in a Disc Manufacturing Environment. The Unit was designed with Duplicators, Web Disc, Game Designers, Media Distributors and Archivalists in mind. The ShuttlePlex can be purchased in Several configurations; as a stand alone unit, external laptop drive or integrated into a PC based duplication system.
-
product
Static Tester for Lab and Workshop
ADSE 715 RS
The ADSE 715 is a complete high performance single pressure Ps stand-alone test bench specially designed to be used in the workshop or in the laboratory to test and calibrate all air data equipment such as altimeters, vertical speed indicators, air data computers ) and sensors. The high precision embedded sensors enable the ADSE 715 to be used as a pressure standard. The user interface running on a PC connected through USB link is programmed underWindows and Labview, with a data base managed in a spreadsheet for easy evaluation, management, statistics and presentation.
-
product
Single-Phase Transformer Winding Resistance Meters
RMO-TW Series
RMO-TW series is perfect for winding resistance measurements of inductive objects. It is ideal for testing transformer windings (power transformers, distribution, autotransformers) and for on-load tap changer verification. In addition, any RMO-TW transformer ohmmeter & tap changer analyzer can also perform transformer demagnetization.The series contains 4 models, with maximal test currents from 10 A (RMO10TW) to 50 A (RMO50TW). They are fitted in a portable and lightweight metal housing.All ...show more -
product
Flying Probe Test System
A8a
The A8a test system provides the flexibility of flying probe testers while delivering high throughput testing for bare board printed circuit boards (PCBs). The target market for the A8a is the electrical test of tablet and PC motherboards and high density interconnect (HDI) products for smart phones. The A8a is designed for high productivity, reliability and test accuracy. To achieve high throughput the key feature of the A8a is a new dual shuttle system, which reduces the product exchange time ...show more -
product
Basic 3U VPX-to-PCI Express (PCIe/PCI-e) Adapter
8462
The Technobox, Inc. P/N 8462 is a 3U VPX-to-PCI Express (PCIe) adapter that provides a convenient and cost-effective means for developing 3U VPX boards in a personal computer environment. It can also be used for production testing of 3U VPX boards. The adapter is a half-length PCIe card with the VPX card under test mounted close to the PCIe edge fingers to minimize signal lengths. When seated in a PC motherboard, the VPX card primary side faces upward to allow convenient access to components.
-
product
Mini Array+
DORC's ZX-1
Direct Optical Research Company
Used primarily to measure multi fiber (MT/MPO and MT-RJ) connectors, DORC's fourth generation "ZX-1 mini Array+" is the result of 18 years of hardware and software product development. Although optimized for mutifiber connectors, the ZX-1 mini Array plus also does an excellent job of measuring single fiber PC and APC connectors. DORC's patented design is based on a variant of the Michelson configuration, and provides BOTH 2D and 3D high resolution images of the sample under test in approximately 45 seconds for multi fiber connectors and just 3-4 seconds for single fiber connectors - from the time the connector is inserted.
-
product
Supported Test Systems
TTCI is a leading solutions provider of application development for test systems from Seica, Keysight, Teradyne, Digitaltest, and XJTAG. We offer a wide variety of testers and test solutions to meet your needs. Our Seica Pilot and Digitaltest Condor flying probe systems can handle all of your low- to mid-volume production, prototypes, and PC boards with accessibility issues. The Keysight 3070 and Teradyne TestStation can address your larger production runs and fixture requirements. In addition, we can also address your functional and boundary scan needs.
-
product
CCFL Ballast Tester
WT2000A-CCFL
This tester is specially designed for analyzing the electrical characteristics of CCFL Electronic Ballast, meets the test requirements in international standard• Input characteristics analysis: measure Vrms, Irms, W, PF, Hz, phase angle Measure THD, 0 to 39th harmonic components, Accuracy: ±(0.4% reading+0.1% range+1 digit)• Output characteristics analysis: measure lamp voltage, lamp current, lamp power, oscillatory frequency, crest factor of lamp current, Accuracy: Class 2• Interface RS-232C provided for easier communication with PC for printing test report
-
product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 125 MS/s on 4 DAQ Channels and 4 AWG Channels
DN2.816-04
The hybridNETBOX DN2.80/81x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 16 bit resolution and is available with sampling rates of 40 MS/s and 125 MS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
product
PC Based Rotor Tester
GTS 1000
The PC Based Rotor tester is the most reliable, fast and cost-effective way to detect faults in the Rotors in less than 10 seconds. This Rotor Tester can Test Large sized Rotors of any Size, Length & Weight that can be mounted on a Load balancing machine or a Lathe and rotated at a speed of 600 rpm.
-
product
Single-Phase Transformer Winding Resistance Meters
RMO-TT Series
RMO-TT series is perfect for measuring winding resistance of inductive objects such as power and distribution transformers or autotransformers. Additionally, every transformer resistance meter from RMO-TT series can analyze:tap changers,generators,electrical motors,high-current busbar joints,cable splices,and welding joints.Transformer demagnetization can also be performed with all RMO-TT instruments.The series is consisted of 3 models, with maximal test current from 40 A (RMO40TT) to 100 A (RMO...show more -
product
VB-8034, 4-Channel, 350 MHz Bandwidth VirtualBench All-in-One Instrument
784343-11
4-Channel, 350 MHz Bandwidth VirtualBench All-in-One Instrument—The VB‑8034 combines a four‑channel, 350 MHz mixed-signal oscilloscope with protocol analysis, an arbitrary waveform generator, a digital multimeter, a programmable DC power supply, and digital I/O into a single device that integrates with your PC or iPad. The VirtualBench all‑in‑one instrument is simple and convenient and results in more efficient circuit design, debugging, and validation. The included software provides an interact...show more -
product
Hand-helds
Hand-helds are portable calibration instruments for mobile use for the accurate measurement and recording of temperature profiles. For the instruments there are various designs of thermometers available. Through this, hand-helds are particularly suitable as test instruments for a large variety of applications in the widest range of industries. Data recorded in the hand-held can be evaluated via PC software, some instruments document calibrations in the internal memory, which can later be read on a PC. Optionally, a calibration certificate can be generated with our calibration software WIKA-Cal.
-
product
Configurable Data-Logging System
NI CompactDAQ
This NI CompactDAQ configurable data-logging system includes an NI CompactDAQ controller or chassis, C Series I/O modules, and Chameleon software. It is designed for structural test and monitoring applications with the NI CompactDAQ controller, which includes built-in processing and nonvolatile storage for running Chameleon software and logging data locally. Alternatively, you can choose a USB or Ethernet chassis for a lower cost system that requires an external PC. This system accepts a variety of C Series I/O modules, so you can mix and match microphones, accelerometers, and temperature and bridge-based sensors.
-
product
Optical power meter with Optical laser Source
Shanghai Baudcom Communication Device Co.,Ltd.
The Multimeter combines a power meter with a 2-wavelength laser source,for optical fiber network installation and maintenance. With the large capacity of data storage,it's very convenient for field testing and transfering the test results to PC through USB interface.
-
product
Electronic Loads
PeakTech Prüf- und Messtechnik GmbH
Can be used for important test procedures in quality assurance as well as e.g. testing of power supplies and control units, batteries, fuel and solar cells. For precise load control for various purposes, this device offers load control according to constant voltage (CV), constant current (CC), constant load resistance (CR) or constant power (CP) with a highly precise resolution of 1mW, 1mV, 1mΩ and 1mA. The device also offers additional test modes, e.g. the battery test or the dynamic test. The PC interface and software offer the option of implementing freely programmable test sequences with data evaluation.
-
product
PCI To PC104 Extender Board
MS 1717
PCI to PC104/EPIC Extender card is used for extending the standard desktop PCI bus to compatible PC104 or EPIC bus. This will help to test all the PC104 cards through standard PC without any embedded processors. This card is very low cost board and very use to interface with standard board. This board also facilitates to debug the PC104 or EPIC boards.
-
product
ECM Noise Under RF Test System
BK8020
The BaKo Type BK8020 ECM Noise Under RF Test System tests microphones under RF noise, using a ‘Direct Injection Test’ in the frequency range of 5MHz~2.5GHz with an amplitude modulated (AM) disturbance signal of 1kHz. You run the system using the controlling PC, which allows automatic configuration and which runs the test sequence automatically. When you finish testing, you can print data as an MS Excel report or save it for comparison and analysis.
-
product
Transistor Curve Tracers
Store characteristic curves and panel setting parameters. Programmable test conditions ,measured results PC stored. Three cursor measurement modes: point, line, window. Two cluster characteristic curves display simultaneouslyfor compare and pairing. Screen read outβ, gm, Vce, Ic, breakdown voltage, leakage current and other parameters . Repeat and single measurement. Self-checking function . 7 Inch high-resolution TFT color LCD. Standard interface: USB, RS232, LAN
-
product
Ultra-Ruggedized Data Recorder for Interactive Vehicle Testing
SomatXR CX23-R
The ultra-ruggedized SomatXR CX22B-R data recorder is intended for use in harsh environments and reliably stores measured data in applications such as vehicle tests. The recorder records data from other SomatXR modules using an Ethernet connection. At the same time, FireWire allows its use as a gateway for direct data transmission to the PC. Both centralized and distributed measurement systems can thus be implemented.
-
product
Micro - Ohmmeter / Milli - Ohmmeter
Basic Accuracy 0.25%Max. Test Current : 5A (120mV) for 7002Max. Test Current : 10A (60mV) for 7272Manual or Auto RangeFour Terminal Kelvin Measurement6 Ranges with 1mV Best ResolutionMeasurement of Resistive and Inductive MaterialsSetting for HI, LO & PASS ReadingsMemory of 3000 Measurements DataProgrammable HI-LO Alarm with memory of 20 DataLarge LCD with Backlight & HOLD FunctionLow Power ConsumptionBattery Operated with AC AdaptorLow Battery (Voltage) AlarmLED indication for Invalid Resistance MeasurementCable Length Measurement in feet & metersUser Interface Software for PC Communication via RS232C(to USB Bridge) cableBuilt-inBatery Chaging Circuit & Calender Clock
