Current Preamplifiers
-
Product
High Output Current Op Amplifiers ≥ 100mA
-
Analog Devices high speed , high output current (≥100 mA) op amps deliver high output current while driving low impedance loads with excellent linearity. Whether it's high output current, low input bias current, wide bandwidth, high slew rate, or low distortion, no one sets more performance standards for next-generation designs with the widest portfolio of leading edge products than Analog Devices.
-
Product
Dual Surge Current Generator
MIG0624T-K12
-
Designed for testing telecom surge protection devices according to ITU-T K12. The generator has two indepedent impulse outputs which allow testing of two and three terminal protection devices such as gas discharge tubes (GDT). The generator can be configured for two terminal devices or with the outputs in parallel to increase the current impulse for two terminal devices.
-
Product
Current Differential Relay
SEL-587
-
Schweitzer Engineering Laboratories, Inc.
The SEL-587 Current Differential/Overcurrent Relay provides protection for any two-input apparatus, such as transformers, motors, generators, and reactors. Apply it for differential and overcurrent protection and use event reports for quick post-event analysis.
-
Product
Current Transformer
DCT 57
-
SHANGHAI POWOO INDUSTRY CO., LTD
Accurate DC measurement, comply to IEC 1036 and IEC 62053. Suitable for a wide range of current (from 1.5A to 100A); linear output current, high precision; compact, delicate appearance.
-
Product
Field Current Regulator
-
We are counted amongst the leading names in the industry, offering wide range of Field Current Regulator. Our entire product line ensures easy operations and is performance based. Field Current Regulator are quality tested and are delivered in standard configurations. Our entire product range has high strength and is delivered at most affordable rates.
-
Product
Wide Range Flexible Current Probe
EFX6000
-
The EFX6000 is a flexible AC current clamp utilizing the Rogowski principle. It can be used to measure currents from 1 amp to 6000 Amps in 2 auto-ranges, over a wide frequency range to 10kHz. The flexible and lightweight measuring head allows quick and easy installation in hard to reach areas, around large conductors and where access to confined or tight spaces is a problem. It requires no batteries or external power supply.
-
Product
Through Hole type DC Current Sensor／for DC Leakage Current Measurements
DCZCT-45NK
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*DC earth fault measurement*DC leakage current measurement*Least affection from the magnetization of core and temperature fluctuation*Convenient ＋24V single polarity power supply
-
Product
High Current Probes (Battery Contacting) HCF73211B065G300A
1165576
-
The High Current Probes (Battery Contacting) HCF73211B065G300A is an advanced contact probe designed to deliver reliable performance in a range of applications requiring precise electrical connectivity and temperature measurement capabilities. With a robust temperature range of -45°C to +200°C, this probe is tailored for environments where durability and accuracy are essential. The basic contact probe design incorporates a pitch of 2.54 mm (100 mil), making it compatible with various electronic setups.
-
Product
Current Meter
Model 106
-
The Model 106 is the ideal instrument for coastal and estuarine applications and other light-duty survey work.
-
Product
High Current Probes (Power Electronics) HCF73517B400G500
1016207
-
The High Current Probes, specifically model HCF73517B400G500, are engineered for superior performance in power electronics applications. This probe excels in environments requiring continuity and precision, drawing a continuous current of up to 50 A while maintaining a typical contact resistance of just 5 mOhm. Its elegant design includes a basic contact probe configuration with a nominal travel distance of 4.4 mm, allowing for reliable and effective operation within a wide temperature range from -45°C to +200°C. With its robust brass shaft and premium materials, such as beryllium copper for the plunger and high-grade steel for the spring, the probe is built to withstand rigorous usage without compromising performance.
-
Product
High Current Probe HCF73211B065G300
1007997
-
The High Current Probe HCF73211B065G300 (item number 1007997) is designed for safe transmission of high electrical currents in test and contacting applications. HCF73211B065G300 focuses on current capacity and low transition losses, as required in battery testing, formation and other e-mobility applications. For HCF73211B065G300, contact resistance, contact force and thermal behavior must be considered together because they influence voltage drop and temperature rise at the contact point. The intended application area for HCF73211B065G300 includes power-electronics testing. The electrical rating of HCF73211B065G300 combines 20 A continuous current with 10 mΩ typical contact resistance. For HCF73211B065G300, spring force is 300 cN at a nominal travel of 4 mm.
-
Product
High Current Probes (Temperature Sensors) TS110TYPK0
1034107
-
The High Current Probes (Temperature Sensors) TS110TYPK0 are specifically designed for precise temperature sensing across a vast range from -45°C to +250°C. This probe is a quintessential tool for professionals needing accurate readings in various environments, thanks to its robust design and high-performance capabilities. With a basic contact probe design, the TS110 stands out with a compact total length of 15.00 mm and a tip style diameter of only 1.10 mm, allowing for easy insertion in tight spaces while maintaining reliability under extreme temperature conditions.
-
Product
Impulse Semiconductor High Current Integrated
Transmission Line Pulse Test System
-
The Impulse Semiconductor High Current Transmission Line Pulse (TLP) test system is the tool of choice for extracting ESD parameters for transient protection devices in a package, or at wafer level. With accuracy better than 100 milliohms at 40 amps peak current, the Impulse high current TLP is specially tailored to the needs of today's ESD device designers who must accurately measure low values dynamic resistance irrespective of breakdown voltage.
-
Product
Current Transformer
ST-40CT
-
Standard Electric Works Co., Ltd
● 200/5A - 400/5A● 3-5V A● Class 1● Insulation 600V
-
Product
Eddy Current Flaw Detector
US-525M
-
United Western Technologies Corp
The US-525M multi-channel eddy current testing instrument is a rugged industrial rack-mounted instrument offering multi-channel testing, integral digital strip chart, as well as Ethernet control and data transfer to meet your in process testing requirements. This instrument offers up to eight channels, with a frequency range of 20 Hz to 10 Mz, a high signal-to-noise ratio, a bright 12-inch diagonal color LCD flat-panel screen, and data storage of 32 Gig. It offers input/output (I/O) capability, USB and Ethernet connectivity, as well as three discrete alarm gates with independent outputs per channel. for your on-line bar, tube, wire and specialty component testing needs.
-
Product
DC to 350 MHz Preamplifier
SR240A
-
Stanford Research Systems, Inc.
The model SR240A 350 MHz Preamplifier is a 4-channel, DC-coupled instrument with a gain of 5 per channel. The amplifiers can be used independently or cascaded to provide gains of 5, 25, 125 or 625.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, Simplified Current Sink, 750 V Isolation
41-752A-903
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Clamp type DC/AC Current Sensor／with Voltage Output
LAD-250
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*With DC voltage output*AC/DC 1A～1000A
-
Product
AC/DC Current Probe, 100 MHz, 15A
N2893A
Oscilloscope Probe
The Keysight N2893A is a 100 MHz bandwidth, active current probe for InfiniiVision and Infiniium oscilloscopes. The probe features flat bandwidth (DC-100MHz), low noise(<2.5 mA rms) and low circuit insertion loss. Auto demagnetization (degauss) and calibration removes any residual magnetism and unwanted DC offset in the probe. The probe is powered directly by the InfiniiVision and Infiniium Autoprobe interface, eliminating the need for an additional power supply.
-
Product
High Current Probes (Battery Contacting) HCF34009S350L400S1
1020515
-
The High Current Probes (Battery Contacting) HCF34009S350L400S1 are designed for precision in electrical connections, featuring a robust Basic Contact Probe design. With a pitch of 4.00 mm (157 mil) and an operating temperature range from -45°C to +200°C, these probes are engineered for extreme conditions while ensuring reliable performance. The unique S1 designation highlights their advanced capabilities tailored for high-current applications, making them indispensable in various industries such as automotive and industrial automation.
-
Product
High Current Probe/DMM
655
-
Another great tool for all around electrical troubleshooting. The #655 is ideal for all high current applications, especially starting and charging diagnostics. The #655 can measure up to 1000 Amps AC or DC. Unit features built-in degrees F and C temperature readings.
-
Product
30A, 100 MHz CURRENT PROBE, BNC, AC/DC, 30A rms, 50A Peak Pulse
T3CP30-100
-
30A, 100 MHz CURRENT PROBE, BNC, AC/DC, 30A rms, 50A Peak Pulse.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-1200B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
Extra-Ground Current Impuision Equipment
JYQ
-
Generally, the way of finding out the iron core ground false of powertransformer is always inefficient, while the method of using the traditional measure such as increase powerful current by welder when finding the false point oftransformer. The transformer needs to be mended on the spot or return to the factory if it can not melt off the point because of low voltage. It will spend high transportation fee and dealing costs, brings huge economic loss. The JYQ iron-coreimpulsionequipment is the intelligence set for exclusiveusing in solving the false of transformer. It can output high-voltage powerful current transientand melt the ground point off rapidly.
-
Product
High Current Probe Receptacle H340
1001698
-
As a receptacle, H340 (item number 1001698) supports precise positioning of the compatible High Current Probe within the contacting system. As a Receptacle, H340 guides and positions the matching Contact Probe; depending on the design, the Receptacle can also provide electrical connection or insulation and supports controlled probe replacement during maintenance. When selecting H340, the matching probe family, installation dimensions and any required connection or insulation design should be considered together.
-
Product
Split type AC Current Transformer
CTS-200
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*1A output for metering application.*Short circuit switch for secondary output is provided for safe operation.*High accurate transformer for the application of first class meter.*Easy installation by metal fitting.
-
Product
High Current Probe HCF34812A600U700A
1133197
-
The Coaxial High Current Probe HCF34812A600U700A (item number 1133197) is designed for safe transmission of high electrical currents in test and contacting applications. HCF34812A600U700A focuses on current capacity and low transition losses, as required in battery testing, formation and other e-mobility applications. For HCF34812A600U700A, contact resistance, contact force and thermal behavior must be considered together because they influence voltage drop and temperature rise at the contact point. The intended application area for HCF34812A600U700A includes battery and power-electronics testing. HCF34812A600U700A is rated for 100 A continuous current with a typical contact resistance of 5 mΩ. HCF34812A600U700A operates with 700 cN spring force and 4.4 mm nominal travel.
-
Product
High Frequency Current Transformer
HFCT
-
The HFCT is a high frequency current transformer designed specifically for picking up partial discharge signals. It has a split core ferrite to allow retrospective fitting to earth straps without the need for disconnection. The durable body has a hinge and a quick release latch, making use quick and easy. The HFCT is constructed with an aluminium body to provide RF shielding and improved performance in noisy environments.
-
Product
Bluetooth Integrated Flexible Coil Current Meter
-
One of the most advantages of the Flexible Coil Current Meter is external wirelessly connect to Smart phone / Tablet / PC to view data, record reading, capture picture with data on it and send the information to headquarter.
-
Product
GAOTek Portable H/L Voltage Clamp Current Leaker
GT00YA00ZX
-
The GAOTek Portable H/L Voltage Clamp Current Leaker measures high voltage current with a 12.5 in (32 cm) insulating rod, adopting the latest CT technology and integrating mask digital technology. This instrument provides high precision, reliability, and stability with its integrated design between transducer clamp and domain. This leaker can be used to measure any wire with or without the insulation layer where the voltage is below 10 kV. The insulating rod is portable, moisture resistant, heat resistant, shock resistant, and insulating. It provides additional functionalities such as online current testing, peak and data holding, data storage, detection of high and low current in primary and secondary circuits separately, and provision of suitable calculations to conclude change in high and low pressure.
