-
product
Remote Particle Sensors
3718-A And 3719-A
Kanomax Remote Particle Sensors with analog output are designed to fit into your existing monitoring system, or they can be used as a stand-alone unit to monitor a critical area when connected to an alarm or controller. With two models available, these 2-channel remote particle sensors are capable of Modbus communication via RS485 interface. 0.1 cfm and 1.0 cfm flow rate models are available, along with flexible 4-20mA analog output with the 1.0 cfm unit (only).
-
product
System Status Monitoring Software
CHM
The R&S®CHM system status monitoring software is an integrated, system-specific solution for continuous monitoring of key system parameters in systems from Rohde & Schwarz. It monitors devices and system components fully automatically, outputs warnings and alarms to operators if system components approach or reach critical operating states, and assists maintenance personnel in fault diagnosis..An extensive set of analysis tools, such as the visualization of measured values in time-sequence charts, helps system administrators to carry out maintenance work and identify errors.
-
product
Barcode Verification Systems
REA ScanCheck 3
The REA ScanCheck 3 is an universal, battery-operated, high-performance barcode verification device which operates in accordance with current standards. The verifications document compliance with quality goals in production and monitoring of barcodes on data storage devices and products of all kinds. The measurement principle is based on a laser scanner optimized for verifications. This makes contact-free measurement, largely independent of handling influences, possible. For mobile use on site, the device operates self-sufficiently, independent of the power network with standard, rechargeable batteries. The operating system and application software support multiple languages.
-
product
Return Path Analyzer
9581 SST
The centerpiece of the Guardian Return Path Maintenance System, the Guardian SST performs the dual functions of supporting Trilithic field units and supplying monitoring data to local and remote controllers. The only DSP-based return path analyzer in the Industry, the Guardian SST is as cost-effective as it is fast and versatile.
-
product
Low-PIM, Low-Power Filter Solutions for Monitoring Broadband Emissions
Bandpass/Bandstop, Notch, and HighpassCompact Design for Rack Mounting of Several BandsSuitable for Monitoring Emissions from Semiconductors,TX/RX Chipsets, SAW/BAW Filters, Cell Phones,Printers, PDA’s, etc.
-
product
Non Contact Temperature Sensors
Non Contact Type temperature measurement involves determining temperature of object surface without direct contact with the surface. Tempsens offers both single point and area inspection model devices which are infrared thermometers and infrared camera and industrial furnace monitoring camera.
-
product
Custom Bolt-On Strain Sensors
Our custom bolt-on strain gauge sensors are designed and manufactured to your application, based on your drawings and specifications, including all types of output formats. Ideal for dynamic load monitoring, capable of measuring and monitoring axle stress and weight with high accuracy.Do you have an application for strain gauge measurement that requires a quick and simple installation, repeatedly, in multiple locations? Perhaps you need a sensor with high environmental protection, which removes the necessity for time-consuming cleaning, complicated soldering and messy strain gauge adhesives?
-
product
Ethernet Modules
The Ethernet Module supports a wide range of network protocols together with a standard RJ-45 Connector. Windows software is provided for testing and monitoring of the various I/O points. The Ethernet Module is compact and easily mounted in existing controllers or new designs for easy network connectivity.
-
product
Health and Usage Monitoring Systems
Honeywell Aerospace Technologies
Health and Usage Monitoring Systems (HUMS) for helicopters provide diagnostic information required for optimum performance. HUMS sensors and embedded diagnostic software monitor and communicate the health and maintenance needs of critical components.
-
product
Environmental Monitoring
Life doesn't stand still and neither do you. An amazingly intuitive web-based control panel gives you the freedom to monitor environments from anywhere.
-
product
Heat Index Monitors
eat Index Monitors have the same two broad sets of applications: industrial (HVAC) and consumer monitoring the heat index, RH, dew point and wet-bulb temperature of an outdoor field for the purpose of improving player and worker safety. The industrial heat index monitors come in two sizes; the pocket-sized consumer versions do not.
-
product
ESG Analyzer
The ESG Analyzer (Electronic Service Guide) is a high-end software application for in-depth analysis and continuous monitoring of ESG data within Mobile DTV multiplexes – ATSC-M/H or DVB-H.
-
product
Burn-In System
The COBIS-II Series Burn-in System is designed to test the latest high frequency integrated circuits (ICs) and combines a large capacity oven with well proven Accutron FlexBID™ dynamic driver technology. This system is engineered for productive dynamic device testing and reliable monitoring.
-
product
FTB Ecosystem
Imagine test tools that actually help you deliver services with speed and quality. Imagine if you could institutionalize operational efficiencies, eliminate silos and make every component of your deployment, turn-up and monitoring part of one tightly woven fabric.
-
product
SingleRide Single-trip PDF Temperature Data Logger
Small, light, waterproof and packaged in food packaging, this data logger is ideal for monitoring the temperature during the transport of: food products, pharmaceuticals, transport of works of art, flowers, transport of blood, etc. Recordings start and stop at the press of a button. Just connect it to the USB port of any computer to get the PDF report directly without software and driver.
-
product
Universal Monitoring System
R&S®UMS400
The ever-increasing frequency range of wireless communications services calls for monitoring stations up to 8 GHz, in some cases even up to 20 GHz. Typically, this requires a monitoring sensor installed close to the antenna(s) in order to keep cable losses as low as possible for highest sensitivity. This is possible for both the R&S®UMS400 and R&S®CS-MC20, thanks to an outdoor housing.
-
product
RS422/RS485 Serial Boards
104-COM-8S
These are eight, four, or two-port, asynchronous, serial communication boards designed for use on the PC/104 bus. They support RS-485 and RS-422 communications. The boards may be installed in any standard PC/104 stack. Connections are made via a 50 pin IDC type right angle connector.Common applications include POS, gaming systems, machine monitoring, military and high-density networking.
-
product
Carrier with System Management
EnsembleSeries™ CCM3011
*OpenVPX carrier module designed to use the Data Plane*PCI/PCI-X interface at up tof 133 MHz on each site*x8, x4 and x1 PCIe interfaces*Advanced OpenVPX system management functionality enables remote monitoring, alarm management, and hardware revision and health management*Conduction-cooled and air-cooled variants available
-
product
Geophysical Services
GF Instruments provides methodical research, near-surface measurements, consulting and services in: engineering-geological surveys (for civil engineering, dams and dikes monitoring, utility mapping, landslides). environmental monitoring and mapping (waste sites, leakages, pollution plumes). UXO surveys. hydrogeological surveys (ground water explorations and protection).
-
product
Bench Digital Multimeter, Calibrated, 1 kV, 10 A, 3.8 Digit
72-1015 CAL
The 72-1015 CAL from Tenma is a digital bench type true RMS multimeter. It has auto and manual range options with maximum reading of 5999 counts and 3-5/6 digits which has a unique outlook design. In addition to all the conventional features including DC/AC voltage, current, resistance, diode, continuity test, diode test capacitance, temperature, transistor, max/min, there is a data hold, low battery display, sleep mode, RS232C serial port for easy connection with computer to realize macro recor...show more -
product
High-density Optical Power Meter.
Power-1410
Quantifi Photonics’ Power-1410 optical power meter provides fast monitoring of signal power from -60 to +10 dBm and broad wavelength range of 1250 to 1650 nm. It provides unrivalled channel density with up to 288 parallel channels in a single 1U rack-mountable instrument.
-
product
USB Analyzer
USB protocol Analyzer is an easy to use USB Data Monitor for Windows. It offers simple, yet complete view for monitoring and analyzing activity of USB devices. USB Traffic Analyzer can intercept, record, display, and analyze incoming or outgoing data between any USB device plugged in your computer and applications. USB device analyzer can be successfully used in development of your applications, USB device drivers or hardware. It is your essential platform for efficient coding, testing, and optimization.
-
product
Optical Power Meter - PXI
Power 1400 Series
The Power 1400 Series optical power meter provides fast monitoring of signal power from -60 to +10 dBm and broad wavelength range of 750 to 1700 nm. With a logarithmic amplifier, it avoids gain-jumps faced by multi-stage linear amplifier power meters.
-
product
Temperature Logger-30 to +50C
TV-4050
This data logger is a self-contained temperature recorder with a digital display. The TV-4050 is ideal for monitoring the temperature of offices, cold storage rooms, museum exhibits and many other applications where a visual temperature indication is needed.
-
product
Three Phase Power Monitoring
PRÜFTECHNIK Condition Monitoring GmbH
A three-phase power monitor detects changes in electrical variables. With power monitoring on your assets, you can help reduce wear and damage, while also identifying what’s causing it. The Fluke 3540 FC three-phase power monitor can be used remotely or through a stationary connection.
-
product
Data Logger for Weather Station, 4G
HD33MT.4
HD33MT.4 with 4G/3G/2G/GPRS modem. Optional Ethernet. Designed for solar power. Integrated charger. Data Logger for weather station - remotely monitoring temperature, humidity, atmospheric pressure, solar radiation, rainfall quantity, wind speed and direction. Calculating sunshine duration.
-
product
Vibration Meters
A vibration meter is used in manufacturing for machine condition monitoring, product testing and quality assurance. Many machine maintenance technicians use vibration meter devices in tandem with sound level meters to analyze frequency. A vibration meter also can be used in civil engineering to measure the vibration of structures such as buildings, roads and bridges. In addition, specialized vibration meter devices can be used to measure the vibration of the human body. Any vibration meter will ...show more -
product
cRIO-9033, 1.33 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, Kintex-7 160T FPGA, Extended Temperature, 4-Slot CompactRIO Controller
783452-01
1.33 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, Kintex-7 160T FPGA, Extended Temperature, 4-Slot CompactRIO Controller - The cRIO-9033 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. You also can use the Mini DisplayPort to add a local human machine interface (HMI) for application develop...show more -
product
In-Situ Spectroscopic Ellipsometer for Real-Time Thin Film Monitoring
UVISEL Plus In-Situ
The UVISEL Plus in-situ spectroscopic ellipsometer can be easily mounted on process chambers (PECVD, MOCVD, sputter, evaporation, ALD, MBE) for the real-time control of thin film deposition or etch processes.The UVISEL Plus in-situ provides the unique combinations of very high speed, sensitivity, dynamic range and accuracy making the instrument able to control deposition / etch at the atomic layer thickness level, even for rapid processes.
-
product
Compact Monitoring Probe
ISDB-T/Tb
Network operators:automate the tests of new transmittertemporary monitoring/investigation toolrebroadcasting receiver: RF to ASI or IPBroadcasters: off-air monitoring probe to validate the on-air contentTV/STB producers: automated tests against a professional receiverLabs: easy & simple access to live DTV sources via RF
