Battery Charge Discharge
-
Product
Ultra Multi-Channel Battery Emulator
-
Peritec Ultra Multi-Channel Battery Emulator is used for the development of electric car(EV). The hardware has great extendability, it can also simulates up to 192ch synchronized DC power supply with high isolation and you can make the test sequence with Mirosoft Excel.It can be used as a power source such as a simulator of new energy development for the evaluation. In addition, we can correspond flexibly to customize provide the best solution to suit the needs of our customers.
-
-
Product
New 12v Battery Load Tester
-
Hangzhou Xun Anda Electrical Co., Ltd.
battery maximum capacity: 120Ah or 1200CCA(SAE)voltage test range: 7-15VDCoperating voltage: 7-15VDC , storage battery power suppliedmaximum power dissipation: 0.5W aroundoperating temprature: -10°C~50°C;operating humidity: 30%~90% (without condensation)display modes four super bright nixie tube with 0.56 inch ,four different color Led indicator lightkeying: three keying total for using related operation
-
Product
Charge Amplifier
-
This compact Charge Amplifier has 3 signal routes.When it is used as the Charge Amplifier for the vibration analysis systemWave Stocker, all setups are possibleby the upgraded software.
-
Product
Regular Battery Tester Models
-
The following are regular battery tester models for single-cell tests (coin cell/half cell/pouch cell/cylindrical cell, CT2001 & CT3001 Models) and supercapacitor test.
-
Product
Partial Discharge
-
Partial discharge (PD) is a local electrical discharge that occurs in imperfections or inhomogeneities. The partial discharge measurement is a so-called “non destructive test” to determine the quality of insulating materials. On the contrary of pure high-voltage test, th test item is not pre-damaged at low PD levels.
-
Product
External Fire Exposure Test Machine, Battery Safety Testing
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL external fire exposure test machine is applicable to the standard UL 2580.
-
Product
Vehicle Battery Charger
6435A
-
Peaceful Thriving Enterprise Co Ltd
This charger use microprocessor to monitor the charging process. Therefore it is a smart charger with protection of reverse connection, over-voltage, over-current, short circuit and over-charging. It has wide working temperature and it has IP54 protection. Cigarette lighter connector and alligator clip can be replaced for power source.
-
Product
Precision Integrated Analog Front End, Controller, & PWM for Battery Test & Formation Systems
-
The AD8452 combines a precision analog front-end controller and switch mode power supply (SMPS), pulse-width modulator (PWM) driver into a single silicon platform for high volume battery testing and formation manufacturing. A precision instrumentation amplifier (in-amp) measures the battery charge/discharge current to better than ±0.1% accuracy, while an equally accurate difference amplifier measures the battery voltage. Internal laser trimmed resistor networks establish the in-amp and difference amplifier gains (66 V/V and 0.4 V/V, respectively), and stabilize the AD8452 performance across the rated operating temperature range.
-
Product
Battery Powered, Multi-Range, Analogue Portable Instrument
Tester SA9083
-
The Tester SA9083 is a battery powered, multi-range, analogue portable instrument. It is primarily intended for use by faultsmen for maintenance testing of telecommunication lines and equipment, subscriber installations connected to exchanges where faultsmen do not have access to a test desk, or where the testing equipment at the local exchange is not staffed during normal working hours. It has three input terminals, a range selector switch and a dual purpose push-button reversing switch (B-A changeover/test cell).
-
Product
Battery and Capacitor Testers
-
Battery test system developed on the basis of the experience and know-how that we have amassed through implementing numerous custom-built battery evaluation systems.
-
Product
Battery Test Equipment
-
The multi-current range battery test systems M340A and G340A are designed for precision battery charge/discharge test, coulombic efficiency (current efficiency) test and supercapacitor test. Voltage and current test accuracy go down to 0.01% of the selected range.
-
Product
150KW AC/DC Rectifier Battery Charger
SD750250G
-
Zhejiang Sandi Electric Co., Ltd
AC-DC Power Rectifier Battery Charger Customized for Lead Acid AGM Gel LiFePO4 Lithium Battery is for DC battery system charging station. With single-phase or 3 phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. 50-750Vdc output voltage range optional, suitable for all types of batteries.
-
Product
CP-059-026 Battery Probes
Battery Probe
Current Rating (Amps): 10Average Probe Resistance (mOhm): 25Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 57Full Travel (mm): 1.45Recommended Travel (mil): 40Recommended Travel (mm): 1.00Mechanical Life (no of cyles): 100,000Overall Length (mil): 221Overall Length (mm): 5.61
-
Product
High Current Probes (Battery Contacting) HC200C06G72PT1000
1034016
-
The High Current Probes (Battery Contacting) HC200C06G72PT1000, identified with order code 1034016, is a meticulously engineered coaxial probe designed for superior performance in harsh environments. With a temperature range of -45°C to +200°C, this probe excels in various applications requiring robust thermal and electrical stability. The HC200 features a 25mm pitch, ensuring precise contact during operation, while maintaining a continuous current rating of 300A, which is crucial for high-demand scenarios. Its typical contact resistance of just 0.20 mOhm further enhances efficiency, minimizing power loss during operation.
-
Product
Heavy Duty Wheeled 12V/24V Battery Powered Jump Start Systems
Boost-All
-
A jump starting solution for repair shops, parking lots and garages. While not designed for continuous jump starts, the Boost•All® offers economy without skimping on quality. This unit provides 12/24V, battery powered jump starting in a narrow, 20” wide portable unit with makes maneuvering between rows of parked vehicles a snap.
-
Product
Partial Discharge Inductor
Tracy
-
Cable testing and diagnostics with the BAUR tracy. The BAUR tracy partial discharge inductor induces a signal at the apparent fault location in the cable from outside. In combination with any PD measurement system, e.g., PHG TD/PD, the induced signal can be located and compared with the result of the partial discharge pre-location. The partial discharge location can thus be determined precisely.* Portable, battery-operated signal coupling device* Suitable for cables and cable accessories* Inductive signal coupling* Aviods costly, unnecessary replacements of PD-free cable accessories
-
Product
Digital Battery Tester with Automatic Test
706
-
Controlled by microprocessor, simply activate the switch once and the #706 applies a precisely timed, 10 second load to the battery. The test results, “OK”,“WEAK” or ”BAD” are then displayed along with the test voltage, until the unit is disconnected. The #706 also tests charging voltage and relative starter current draw.
-
Product
Basic Solid-State Battery & Pouch Cell Test Cell
BSS1
-
BSS1 Basic Solid-State Battery & Pouch Cell Test Cell is designed for solid-state battery, liquid battery or in-situ electrochemical research where stable assembly pressure, reliable sealing and repeatable cell geometry are important. It supports laboratory-scale testing, method development and custom battery fixture projects.
-
Product
Battery Tester
B1706
-
ZHANGZHOU HUAYI ELECTRONICS CO.,LTD.
*No test leads needed*Easy-to-read color scale*Self powered-no need of battery *1.5V=AAA,HP16,MN2400,RO3 AA,HP7,MN1500,UM3 C,HP11,MN1400,SP11,LR14,LM2 D,HP2,MN1300,SP2R20,UM1
-
Product
Lipo Battery Power Level Tester & Alarm to Indicate Low Power
#52023
-
Can be used for 7.4V (2S pack)and 11.1V (3S pack).Red LED will flash when cell is below 3.3V and an Alarm will sound when cell is below 3.0V indicating the Lipo Battery pack should be recharged.
-
Product
Battery Temperature Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood climatic chambers for battery can be tested under controlled temperature and humidity conditions, similar to the conditions under which batteries operate during their lifetime.
-
Product
Battery Extra Load Units
-
Performing capacity/discharge test on a high-capacity battery may be challenging since high requirements are set on the discharge system. In cases when discharge test times need to be reduced, high load capacities are required from the discharge system. The battery extra load unit BXL is an additional load unit designed especially for this purpose.It is primarily used with BLU battery testers. However, the unit is a universal add-on device. This means it can be used as an additional load with any other discharge/capacity tester in the market.When discharge current exceeds the capacity of a single BLU device, extra load unit increases discharge capacity. A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way in accordance to battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.
-
Product
Temperature & Battery Testing
-
Conducted to determine how a battery performs under different temperature ranges.
-
Product
Battery Pack Test Equipment For 1-2 Series Battery
TOB-W602
-
Xiamen Tob New Energy Technology Co., Ltd
1-2 Series Battery Pack Test Equipment Used For Mobile Phone Battery Performance Testing 0-10V
-
Product
PathWave BenchVue Advanced Battery Test And Emulation Software For A Single Instrument
BV9211B
-
Achieve higher accuracy, repeatability, and safety with an emulation based on a unique battery model. Your model will allow you to determine your device's power consumption, emulate an actual battery, and import existing battery models.
-
Product
Battery Test & Management
-
Kongter Test & Measurement Co., Limited
Kongter offers a whole line of products for testing and measurement of battery from your critical power systems. It includes battery online monitoring system, battery tester for internal resistance/conductance, battery charger, battery load bank, battery data logger, battery charger/discharger and so on.
-
Product
Collapsible 6 Inch Charge Plate Monitor Assembly
CPM-760A
-
- 6" x 6" (15 cm x 15 cm) conductive plate- Total system capacitance of 20 pF ± 2 pF- Meets the requirements of ANSI/ESD STM3.1 and ANSI/ESD SP3.3- Designed to perform audits on overhead ionizers and room ionization systems- Flexible to also evaluate and balance bench top ionizers- Completely collapsible for compact storage- Designed to be used with the PFM-711A and PFM-711B
-
Product
Swagelok-Type Three-Electrode Battery Test Cell
STB1
-
A Swagelok-type three-electrode electrochemical test cell designed for battery research, electrochemical analysis, catalyst evaluation, and laboratory material testing.
-
Product
Intelligent Battery Tester
CHROME
-
Simulating a 20 hour discharge test in seconds, the ACT CHROME displays the DC Voltage and available Ampere hour (Ah) capacity of standby lead acid batteries between 1.2Ah and 200Ah.
