PMC
PCI Mezzanine Card
-
Product
ARINC825 Cards
-
AIM’s ARINC825 cards can work either with full functionality as an active CAN node for testing and simulating or in listening only mode for monitoring and recording purposes of Avionic CAN bus (ARINC825) applications on up to 4 electrically isolated CAN bus nodes concurrently. All nodes are in conformance with the ISO11898-1/-2 standard. They are accessible by software separately and can be used as 4 independent CAN bus nodes. An onboard IRIG-B time decoder allows users to accurately synchronize single or multiple modules to a common time source. All supported signals are available through front I/O and rear I/O interface. ARINC825 cards consist of FPGA based CAN interface controllers as well as a FPGA based 32-bit microcontroller core and a separate processor for IRIG-B synchronization with high resolution time stamping. All nodes are operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s with the intelligence to process scheduling of CAN frames in real time onboard to significantly off-load the host processor.For embedded applications the AMC825-4 PMC module is available in a conduction cooled version. Using AIM’s family of PCI, CPCI (3U and 6U) and VMEbus carrier cards for PMC our clients have off the shelf solutions in a broad range of card formats. ARINC825 (CAN bus) modules are delivered with an Application Programming Interface (API) and Driver Software compatible with Windows, Linux and VxWorks.An ARINC825 Resource Component is available for AIM’s PBA.pro™ databus test and analysis tool including Tx and Rx simulation capabilities, a Chronological Bus Monitor and support for decoding of payload data within CAN messages. This allows to implement a powerful ARINC825 (CAN bus) analyzer or a complete test system in conjunction with other AIM avionics databus interfaces and PBA.pro™ supported 3rd party hardware.
-
Product
Analog Input Module
PMC341
-
These modules have sixteen analog inputs which are sampled as two eight-channel banks. Eight A/D converters (ADCs) permit simultaneous conversion of all eight channels in a bank. All 16 channels share two generous 512-sample memory buffers. Conversion of each bank requires only 8µS, and all 16 channels can be sampled in just 16µs.
-
Product
Interface (PMC)
QPM-1553-TB
Interface
The QPM-1553-TB provides the highest level of performance, flexibility and interface density for MIL-STD-1553A/B via PMC (PCI Mezzanine Card) to Thunderbolt 3 device. The QPM-1553-TB is integrated with powerful software that reduces development time. All 1553 databus functionality is supported from our advanced API (Application Programming Interface).
-
Product
Compatible Bi-Directional Serial Data Interface
PMC-BiSerial-IO-II
-
The PMC BiSerial has been updated to be even better. Building on the knowledge and experience gathered from multiple IP and PMC BiSerial implementations and adding in the latest technology has created the PMC-BiSerial-II. The BiSerial II features completely isolated FIFOs with 32 bit ports for increased adaptability and performance.
-
Product
PMC Modules
ARINC 429
-
Sycos range of ARINC 429 PMC modules offer the user up to 32 channels on a single width PMC module. Each channel can be programmed independently to operate at either high or low speed. Firmware options available for Tx Error Insertion and Rx Error Reporting are available.
-
Product
Rugged Embedded ARINC429 Conduction Cooled PMC Card
AMCE429-x
-
Rugged embedded ARINC429 conduction cooled PMC card.
-
Product
High Density 68 pin
HDEterm68
-
The high density 68 pin SCSI II/III connector is being used for purposes other than SCSI interfaces because of board and front panel space limitations. For example in the PMC environment the SCSI connector provides an excellent size and pin count for the front panel space allowed. The SCSI connector while dense, is not easy to connect to with wiring intended to go to multiple locations
-
Product
Virtex-4 FPGA with Plug-in I/O
PMC-LX
-
Acromag’s PMC-LX boards use a high-performance Xilinx® Virtex-4TM FPGA, but maintain a relatively low price point. They are optimized for high-performance logic, featuring a high logic-to-feature ratio and a high I/O-to-feature ratio. Two modules let you select a FPGA to match your logic requirements.
-
Product
Interface
P-SER
Interface
P-SER I/O product is a native PMC form factor interface providing real-time serial input and output with high time-precision reception/input time-stamping, scheduled transmission/output, event triggering and interrupt support. This interface is designed to meet the needs of both the simulations/test and the real-time embedded applications whether in Windows or VxWorks environments.
-
Product
PCI Edge Connector Card
PMC239/F
-
The PMC239/F also comes with a fan. The fan can be disconnected from its power if not needed.
-
Product
Mezzanine Cards
-
PMC and XMC are the quasi standard for mezzanine cards in VME systems. esd's PMC and XMC modules extend your system with a bus interface (CAN, EtherCAT, Ethernet) or an intelligent sub system (e.g. XMC-CPU/2041, PMC-CPU/440). Furthermore esd develops customized PMC and XMC modules. VME systems without PMC slot can be extended with an esd VME-PMC-Caddy or PCIe-XPIMC-Carrier board.
-
Product
CompactPCI
6U PMC Carrier
-
This conduction cooled 6U CompactPCI dual slot PMC provides an active interface between the CompactPCI bus (backplane) and a PCI Mezzanine Card (PMC). This product addresses the needs of aerospace, military, and rugged applications. It contains a thermal heat frame made of aluminum that fits together with conduction cooled PMC modules. Conduction cooling conducts heat away from the hot spots of the board and transfers the heat to the card edges and to the system chassis. No active ventilation is necessary inside of the system, which means the boards are sealed from the environmental influences found outside of the chassis. The heat frame and integrated wedge locks for the conduction cooling stiffens the carrier and PMC module enabling the board to resist high shock and vibration.
-
Product
Interface
RCNIC-A2PA3
Interface
The RCNIC platform is a high performance, 3U CompactPCI module (PMC on carrier card) for the AFDX/ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation. An IRIG-B receiver/generator is included for synchronization to an external IRIG-B time source and for synchronization between multiple RCNIC boards.
-
Product
Virtex-5 FPGA with Plug-in I/O
PMC-VLX
-
Acromag’s PMC-VLX boards feature a reconfigurable Xilinx® Virtex™-5 FPGA enhanced with multiple high-speed memory buffers and a high-throughput PCI-X interface. Field I/O interfaces to the FPGA via the rear J4/P4 connector and/or with optional front mezzanine plug-in I/O modules.
-
Product
Cots Boards
-
Built in strict adherence to open architecture standards, Data Patterns designs COTS module products which are used in today's rugged applications and automatic test equipment platforms. Open standard form factors include cPCI, FMC & XMC, IP, MM, PCI, PCMCIA, PMC, VME, VPX and VXI.A portfolio of 'Off the Shelf ' products for testing and on-board applications have been developed by Data Patterns. COTS boards developed have been sold to many customers, in India as well as Europe and North America. They are used for system level products such as Automatic Test Equipment, Rugged Military Electronics, etc.Data Patterns focus on building COTS product is to provide the technological capability to develop system level products with very fast run around times. Use of Data Patterns' COTS module in system level products ensures Data Patterns ability to maintain the products for a significantly longer life cycle. The proximity to the system level engineering team with the COTS development team ensures that end applications are delivered faster, enabling a shorter time to market for the customers
