Thermocouple Loggers
Data Acquisition from thermocouples and data record of termperature events.
See Also: Temperature Loggers
-
Product
J-Type Thermocouples (Ungrounded) (32 deg F to 900 deg F )
745685-J02
Thermocouple Contact (ITA)
J-Type Thermocouple, 32°F to 900°F Temperature Sensor - The J-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the J-Type Thermocouple and acquire synchronized temperature data in units of degrees. The J-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
Product
K Thermocouple Surface Probe
TP772
-
Surface thermocouple Type "K" probe. °C max: 400. Response time: 3 s.
-
Product
Pocket-size temperature logger
DEFI2-T
-
DEFI2-T is a high-precision miniature water temperature recorder for long-term observations (approx. 573 days for 1 minute interval observation). The reduced size of the DEFI2-T allows the device to be installed in large numbers in a single mooring system, allowing investigating temperature fluctuations at increased spatial resolution. Also, AAA alkaline batteries used by DEFI2-T are easily available, reducing the operating costs.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Thermocouple Calibrator
CA10
-
Dual function CA10 Thermocouple Calibrator can be used to source Type K thermocouple output values or measure Type K thermocouples. Quickly select output value using the rotary switch with coarse and fine adjustments.
-
Product
Logger and Handheld Instruments for Temperature Measurement and Monitoring
-
Temperature measurement and monitoring is vital for the quality of temperature-sensitive products wherever they are studied, produced, stored or transported.
-
Product
Thermocouple Probes
Type T
-
No matter the application, ThermoWorks has a probe for you: penetration probes, immersion probes, air probes, surface probes, wire probes, even specialized probes like griddle probes, burger probes, pipe clamp probes, and probes for medical and lab use. Choose from standard tip, reduced tip, corkscrew tip, alligator clip, or needle probes; different handle types; and straight, coiled, stainless overbraid or even armored cables. Sensor types include type T or type K thermocouples, RTD sensors and our Pro-Series® line of thermistor probes.
-
Product
Temperature Data Logger
TGU-4017
-
Self-contained temperature recorder Delayed start option 32,000 readings capacity High accuracy and reading resolution Fast data offload Splashproof case Low battery monitor User-replaceable battery USB or serial download cables User-programmable alarms
-
Product
K Thermocouple Immersion Probe
TP741
-
Immersion "K" Type thermocouple probe. Stem diameter 1,5 mm.
-
Product
Thermometer Hygrometer Data Logger
S3120E
-
Data logger is designed for record of temperature and humidity. Values are stored to a non volatile electronic memory. Data transfer to the personal computer for further analysis is performed via USB, RS232, GSM or Ethernet interface by means of a proper communication adapter.
-
Product
Gauge Type T Thermocouple Wire
W-TW-26
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Tool, Extraction, TriPaddle and Thermocouple, Receiver and ITA
910110102
Extraction Tool
Tool, Extraction, TriPaddle and Thermocouple, Receiver and ITA
-
Product
SparkFun Thermocouple Breakout
MAX31855K
-
The SparkFun MAX31855K Thermocouple Breakout is a simple 14-bit resolution, SPI-compatible, serial interface thermocouple digitizer that makes reading a wide range of temperatures possible. A thermocouple works by taking two wires made of dissimilar metals, connecting them at the two ends, and making a temperature gradient between one end and the other (a 'hot' end and a 'cold' one). Once this is achieved, a voltage potential is formed and current flows. The SparkFun Thermocouple Breakout takes a standard Type-K thermocouple in one end, digitizes the temperature measured and sends that data out the other end via a SPI interface, thereby interpreting the data and translating it for you to read!
-
Product
Thermocouple Power Sensors
N8482A
Power Sensor
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
Product
Temperature/Relative Humidity Logger - Grey Case
TV-4501
-
Temperature and relative humidity recorder LCD display of current readings 30,000 readings capacity High accuracy and reading resolution Fast data offload Splashproof case Low battery monitor and battery low indicator Programmable alarms Optional audible alarm box USB and serial download cables
-
Product
Data logger for Temperature Humidity and Differential Pressure
DSR-THDP
-
Simultaneously measures and logs temperature, humidity and differential pressure Support on-line linear calibration and zero setting Customized differential pressure measuring range between 0 and 1000Pa Suitable for pharmaceutical workshops, electronic production, precision machinery and other applications
-
Product
K Thermocouple Immersion Probe
TP656/1
-
“K” Type thermocouple imemrsion probe. Tolerance according to IEC 60584-2 standard. °C max: 1000. Response time: 1 s.
-
Product
Data Loggers
-
Extensive line of single-channel data loggers for recording voltage, current and temperature, plus multi-channel voltage and current recording devices. All models include software for data storage, analysis and printing.
-
Product
Data Logger
DL6
-
Monitor and troubleshoot HVAC systems, verify energy management systems, or track performance of pneumatically controlled valves with Series DL6 Pressure/Temperature/RH Data Logger.
-
Product
Temperature logger with self-contained sensor and connection for a probe
TGU-4510
-
Dual channel temperature recorder 32,000 readings capacity High accuracy and reading resolution Fast data offload Splashproof case Low battery monitor User-replaceable battery USB or serial download cables User-programmable alarms
-
Product
Pressure Micromanometer – Thermometer Data Logger
HD2114.2
-
Handheld micromanometer - thermometer data logger with 20mbar built-in sensor
-
Product
Data Loggers,
-
Reported – Current values and status are displayedTrended – A set of recent readings are displayed on a rendered chart. The number of sample and other parameters are configurable.Logged – Data is time stamped and appended to log files on a FIFO basisArchived – Real time data is appended to archive files which are zipped to save space. Many configurable parameters.Served to the Web – Using JSON, HTTP , data push services are provided. Data can be pushed from site to www.Served to the Enterprise – Using XML and other enterprise protocols.Provide Visualization – Complex web based GUI is provided. Objects can be animated with live data.
-
Product
Environmental Monitors & Loggers
-
Littlemore Scientific Engineering Co
Designed primarily for museums and art galleries these units measure the environment helping to ensure that sensitive objects are not damaged.
-
Product
All Measurements 3 Channel Portable Data Logger
DO9847
-
Combinations of all measurements in 3 channel portable datalogger: RH, temperature, pressure, airspeed, light, voltage and current.
-
Product
MAX31855 T-Type Thermocouple Arduino Shield
SEN-30004-T03
-
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino.Each order comes with one board and a set of four female, long extension, headers that can be soldered to the board. If stacking two of these modules on top of each other, please order both a Ch 0-3 and a Ch 4-7 board, as well as an additional set of headers for stacking. We're working on sourcing even longer headers, but the ones currently available are not long enough to stack as-is (they need to be double-stacked).The MAX31855T supports a measured temperature range of -270C-400C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or MegaNote: we also offer a universal version of this board in a smaller for factor, the SEN-30003-T.FeaturesType-specific, miniature-sized vertical thermocouple connectors (vertical flat blades, see pics)Measures four (4) thermocouple channels, full extended range.Boards are stackable. Up to 8 thermocouple channels may be connected to an Arduino.14-bit SPI interfacePlugs directly into an Arduino Uno or Mega form factor with built-in voltage level translation on-board.Standard Arduino female headers required for easy configuration, one set included with order (1-6x1, 2-8x1, 1-10x1 0.1" female stackable headers), not soldered on.Detects shorts to GND or VccDetects open thermocoupleOther versions available (K, J, and T stocked). Contact Customer Service to place a custom order.Mounting holes for 4-40 sized screwsConnections are spaced for 0.1" pin headerDesigned, manufactured, tested and shipped from the USA The MAX31855T supports a measured temperature range of -270C-400C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
Product
Cable Assy 78-Pin D-Type Female to 24 x Mini Thermocouple Plugs, 1m
A078DFR-24M002T5A100
Cable Assembly
This 78-pin D-type thermocouple cable assembly is terminated with 24 male mini thermocouple plugs. It is constructed from 7/0.15 (26AWG) silver plated copper wire and screwlocks are provided to secure the D-type to its associated products.
-
Product
Data Loggers
-
Diversified Technical Systems, Inc.
DTS offers a full line of high performance data acquisition systems, sensors, accessories and software to meet a wide range of critical test requirements. Let the DTS team of experienced engineers and test professionals help you find the right instrumentation for your application.
-
Product
AC Event Data Loggers
-
The Track-It™ AC Event Data Logger is a battery powered stand alone compact data logger that records up to 64,000 on/off cycles. Use the Track-It™ AC Event Data Logger to monitor cycle patterns of pumps, blowers and other electrical equipment powered by 120 or 240Vac.
-
Product
Temperature logger with probe-40 to 125C
TK-4023
-
Temperature recorder 16,000 readings capacity High accuracy and reading resolution Fast data offload Low battery monitor User-programmable alarms User-replaceable battery
-
Product
High Temp Loggers
-
Bendable probe with rigid tip, measures up to 662°F (350°C)Monitor temperature inside bottles, vials, hard-to-reach placesHighly accurate over wide measurement rangeN.I.S.T. traceable calibrationRugged, submersible, for use in harsh environmentsNon-volatile solid state memory for maximum data securityUser replaceable batteryEasy to program and download
