Block Upconverters
-
Product
Block Up-Converter
-
RF Lambda’s block up-converters are used to convert IF frequencies up to RF. They can include power amplifiers for high output power and signal conditioning such image rejection as required by the system.
-
Product
Frequency Converters
-
CAES offers a full range of custom frequency converter solutions including narrowband, wideband and block upconverters and downconverters.
-
Product
Block Up-Converter
BUC Series 5” x 2.5” x 0.6”
-
*Connectorized Package *Compact, Rugged Design *C, X, Ku, K, and Ka-Bands Available *L-Band Inputs (950-2150 MHz) *Internal or External Filters Available *Variable Attenuation Control via CAN +5V Logic, SPI, RS232, or I²C
-
Product
Block Upconverter Modules
-
Analog Devices offers the most compact, robust portfolio of block upconverter solutions for high performance millimeterwave applications. Our block upconverter selection ensures that designers have access to the best performance and options for their demanding application and frequency conversion needs.
-
Product
TX / RX Module
-
RF Lambda’s TX /RX modules include both a block upconverter and downconverter. They can include front end amplifiers for lower noise figure or power amplifiers for high output power of signal conditioning and image rejection as required.
-
Product
Dual Band Block Up-Converter
DBUC Series
-
*Connectorized Package *Wide Choice of Frequency Ranges *Dual Band *Integrated Filters *Gain Control *CAN, RS-232, I2C, or SPI Control *Internal / External References *Low Power Consumption *Low Phase Noise *Low Spurs
-
Product
ULI-211E - Heavy Industrial RS-232/422/485 (Terminal Block) To Multimode Fiber (ST Connector). Panel Mount Metal Chassis
BB-FOSTCDRI-PH-MT
Terminal Block
Converts serial data signals to multi- or single-mode fiber2 KV, 3-way isolation (input, output, power circuits)Data rate: 9.6 to 115.2 kbps (bit-wise enable)-40 to +85°C wide operating temperatureIP30 metal panel mount case (DIN rail adaptable)FCC, CE, IEC-61850-3, IEEE 1613, UL C1/D2Note: 2 units required to extend data via fiber optic connection (see datasheet)10-48 VDC power source required (not included, sold separately)
-
Product
Terminal Block For 34933A And L4433A 4x8 Matrix
34933T
Terminal Block
The Keysight 34933T is a terminal block for the 34933A 4x8 Matrix and the L4433A 4x8 Matrix used for discrete wiring. It supports up to 20 AWG wire size typical for <100 connections or 24 AWG for >100 connections. The following two terminal blocks facilitate wiring connections to the 34933A module and L4433A instrument.
-
Product
NI TB-2642B Terminal Block for NI 2532B as 1-Wire 16x32 Matrix Topology Without Column Protection Resistors
782385-05
Terminal Block
The TB-2642B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 8x64 matrix. You can directly connect the TB-2642B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2642B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
Terminal Block and SCSI-II 68 Pin Connector with 1 Meter Cable
U2901A
Terminal Block
The Keysight U2901A is an accessory compatible and recommended to be used with the U2300A Series USB Modular Multifunction Data Acquisition and U2500A Series USB Modular Simultaneous Sampling Multifunction Data Acquisition. The pin-outs of the U2901A is dependent on the USB Data acquisition unit that it is working with. For more information, please refer to the data sheet or the user guide of the USB Data Acquisition unit that U2901A is to be used with.
-
Product
DC Block, 50 kHz to 26.5 GHz
N9398C
DC Block
The Keysight N9398C DC block offers a new level of DC blocking with performance specified from 50 kHz to 26.5 GHz. This DC block features a broad frequency range, excellent return loss, very low insertion loss and excellent temperature stability.
-
Product
SMB-2163, Single-Ended Digital I/O Accessory (Rack-Mountable)
778747-01
Terminal Block
The SMB-2163 helps you connect to compatible single-ended PXI Digital Waveform Instrument for testing and debugging. This terminal block features 32 single-ended digital I/O channels and 5 single-ended control I/O channels. The SMB-2163 also features one 68-pin DDC connector, 37 SMB jack connectors, and one banana-style connector.
-
Product
SCB-68 HSDIO, Shielded 68-Pin Connector Block For R Series DIO & HSDIO Products
782914-01
Connector Block
The SCB-68 HSDIO is a shielded I/O connector block with 72 screw terminals for connecting signals to a 68-pin VHDCI connector. The connector block can be DIN-rail mounted as an option.
-
Product
Shielded Cable for PXIe-4330 and PXIe-4331 to Rackmount Terminal Block, 1 Meter
786341-01
Terminal Block
Shielded Cable for PXIe-4330 and PXIe-4331 to Rackmount Terminal Block, 1 Meter
-
Product
68-Pin SCSI Micro-D Connector Block
44-965-068-F
Connector Block
Suitable for use on the front of PXI BRIC modules this connector block provides a simple method of connecting to high density 68-Pin SCSI Style Micro-D connectors. The screw terminals accept wires up to 20 AWG and use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
Product
50-Pin Male D-SUB, Screw Terminal, 150 V, DIN Rail Terminal Block
782866-01
Terminal Block
NI-TBX-50B, 50 Pin Dsub Screw Terminal Block
-
Product
PXI-2800, 4-Slot PXI Carrier Module for SwitchBlock
781420-00
Switch Block
4-Slot PXI Carrier Module for SwitchBlock - The PXI‑2800 is a carrier module for SwitchBlock that can hold up to six SwitchBlock relay cards while occupying four PXI slots. By connecting multiple SwitchBlock relay cards through the carrier’s integrated analog bus, you can easily create large matrices with more than 2,000 crosspoints in four PXI slots and more than 8,000 crosspoints in a single PXI chassis.
-
Product
NI-9962, 3-Pin 3.5mm Push-In Spring Terminal Block Plug
787104-01
Terminal Block
NI-9962, 3-Pin 3.5mm Push-In Spring Terminal Block Plug, Qty 4, With 26 Awg Ferrules, Qty 20
-
Product
NI TB-2640B Terminal Block for NI 2532B as 1-Wire 4x128 Matrix Topology Without Column Protection Resistors
782385-01
Terminal Block
Screw Terminal, Ribbon, 4x128, 1-Wire PXI Module Matrix Terminal Block - The TB-2640B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 4x128 matrix. You can directly connect the TB-2640B to the front panel I/O connectors … of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2640B also provides optional isolation resistors to protect the reed relays from capacitive loads.This 782385-01 card does NOT have 100 Ohm protection.
-
Product
NI TB-2644B Terminal Block for NI 2532B as 1-Wire Dual 8x32 Matrix or 2-Wire 8×32 Matrix Topology Without Column Protection Resistors
782385-09
Terminal Block
The TB-2644B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 8x32 or 1-wire dual 8x32 matrix. You can directly connect the TB-2644B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2644B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
Terminal Block For 34952A And L4452A Multifunction
34952T
Terminal Block
The Keysight 34952T is a terminal block for the 34952A and L4452A Multifunction with 32-bit DIO, 2-ch D/A and Totalizer. This terminal block is used for discrete wiring. It supports up to 20 AWG wire size typical for <100 connections or 24 AWG for >100 connections. The 34952T is a detachable terminal block with screw-type connections that provides a flexible method for connecting external wiring.
-
Product
NI 9924 Front-mount terminal block for 25-pin D-Sub Modules
781922-01
Terminal Block
NI 9924 Front-mount terminal block for 25-pin D-Sub Modules
-
Product
Terminal Block For 34923A Multiplexer
34923T
Terminal Block
The Keysight 34923T is a terminal block for the 34923A 40/80-channel reed multiplexer, used for discrete wiring. It supports up to 20 AWG wire size for up to 100 connections or 24 AWG for 100 connections or more. Two terminal block options facilitate wiring connections to the 34923A module.
-
Product
Terminal Block For 34938A 20-Channel 5 Amp Form A Switch
34938T
Terminal Block
Use Keysight's 34938T terminal block for the Keysight 34938A 20-channel 5-amp form A switch for discrete wiring. It supports up to 20 AWG wire size typical for < 100 connections or 24 AWG for > 100 connections. The 34938T terminal block is detachable with screw-type connections that provides a flexible method for connecting external wiring.
-
Product
NI TB-2627 Screw Terminal Block for NI PXI-2527
779358-01
Terminal Block
The TB-2627 provides the necessary routing to configure the PXI-2527 or PXIe-2527 PXI Multiplexer Switch Modules as a single or dual 1-, 2, or 4-wire multiplexer. You can directly connect the TB-2627 to the front panel I/O connectors of the PXI-2527 or PXIe-2527.
-
Product
DC Block, 700 kHz to 67 GHz
N9398G
DC Block
The Keysight N9398G DC block offers a new level of DC blocking with performance specified from 700 kHz to 67 GHz. This DC block features a broad frequency range, excellent return loss, very low insertion loss and excellent temperature stability.
-
Product
TB-2648, Screw Terminal, 4x128, 1-Wire PXI Module Matrix Terminal Block
781131-01
Terminal Block
Screw Terminal, 4x128, 1-Wire PXI Module Matrix Terminal Block - The TB-2648 provides the necessary routing to configure the PXI-2531 or PXIe-2531 PXI Matrix Switch Module as a 1-wire 4x128 matrix. You can directly connect the TB-2648 to the front panel I/O connectors of the PXI-2531 or PXIe-2531.
-
Product
NI TB-2646B Terminal Block for NI 2532B as 1-Wire Quad 4x32 Matrix topology With Column Protection Resistors
782385-14
Terminal Block
The TB-2646B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire dual 4x32 or 1-wire quad 4x32 matrix. You can directly connect the TB-2646B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2646B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
ULI-234TE - Heavy Industrial RS-422/485 (Terminal Block) Isolated Repeater
BB-485OPDRI-PH
Terminal Block
RS-422/485 Repeator2kV, 3-way isolation (input/output/power)Data rates:1.2 to 115.2 KbpsWide operating temperature range: -40 to +85 °CIEC-61850-3, IEEE-1613, NEMA TS2, FCC, CE10 to 48 VDC input power (power supply required, sold separately)
-
Product
Terminal Block For 34924A Multiplexer
34924T
Terminal Block
The Keysight 34924T is a terminal block for the 34924A 70-channel reed multiplexer, used for discrete wiring. It supports up to 20 AWG wire size for up to 100 connections or 24 AWG for 100 connections or more. Two terminal block options facilitate wiring connections to the 34924A module.
