Open Short
Pinpoint open circuits.
-
Product
PXIe 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
42-205-008
Fault Insertion Unit
42-205-008 (PXIe) is a 8-channel fault insertion switches designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. They available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
Product
An IEC 61000-4-11 Full Compliance Voltage Dip SimulatorModel: VDS-2002
VDS-2002
-
NoiseKen's new VDS-2002 offers easy and accurate test and following features: Dip, swell, interruption and variation tests up to 16A 240V single-phase AC, interruption test up to 125V DC, preset levels 0%/40%/70%/120%, open and short mode selection for interruption and optional Windows software.
-
Product
Lan Cable Tester
-
Shanghai Beha Electronics Co., Ltd.
Is a newly designed tool,that can easily test the correct pin configuration of the RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc., By comparing one transmitting end and the corresponding receiving end, the 9185B Lan cable tester also can test installed cable far away by using the remote receiving unit., Provides the variety for wiring check, such as cable continuity, open status, short status and miss wired.
-
Product
Automatic and Accurate Inspecting Systems
Circuit AOI
-
The Circuit AOI system is designed to perform automatic and accurate inspecting systems. It integrates rigid mechanical system with advanced vision technology and manufactured and tested by strict is standards. It is suitable for circuit inspection for PCB/FPC, verification and repair. Innovation and unique inspection algorithms are applied to inspect open, short, protrusion, nick, scratch, pin hole, island, line width/space violation, object missing and others defects. AOI system can use offline setup project and check results. It will improve the throughput.Compare to halogen lighting, the full angle LED lighting of Circuit AOI can obtain the best image contrast and is good for different panel type inspection.
-
Product
Network Cable Tester
AVJoG Rack
-
*A single box solution for testing AV cables. *Easy to use with only one button operation. *Detects Open, Short and Crossed circuits. *LCD display for test results. *All major AV connectors present, no need for extra adaptors. *40+ preprogrammed cable types.
-
Product
HDMI Cable Tester
MT-7062
-
Test all HDMI cables with Type A to A, A to C and C to C connectorsDesign with loopback function allows test HDMI type A to A, A to C on main unit.Automatically fast & slow scan for testing all conductors status in a cable, Manual test for step by step detecting individual conductors for intermittent faults.Automatically detect wiring on HDMI type A or type C condition in straight, short, open, crossover in all RGB conductors.Quickly troubleshoot and verify HDTV installation and DIY termination in the field.
-
Product
Digital In-Circuit tester
MTS180/300
-
Analog in-circuit inspection and function inspection are realized on this inspection equipment. IC pin float function is standard equipment. The MTS180 is a press type jig, and the MTS300 is a vacuum type jig. In the board mounting process at the production site, electrical inspection is performed on the mounted board after component mounting, and non-defective or defective products are automatically judged. The main inspection contents are short / open inspection, analog inspection of resistors, capacitors, coils, diodes, etc., lead floating voltage measurement of QFP and BGA, Digital IC inspection, frequency measurement.
-
Product
Cable Testers
-
The CableTool uses TDR (Time Domain Reflectometry) technology to quickly identify an open or a short from 0 to 2,500 feet within a foot of the fault.
-
Product
3-in-1 OSL Mechanical Calibration Kit, DC To 50 GHz, 2.4 Mm (m)
85564A
Mechanical Calibration Kit
The 85564A 3-in-1 mechanical calibration standard combines an open, short and load standard in a compact unit. The product is small, easy to handle, and lightweight. All standards in the 85564A are male 2.4 mm.
-
Product
4-Wire Resistance Measurement | Continuity & HiPot Cable & Wire Harness Testers
-
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty crimps, recessed pins, pin contact contamination, improper wire gauge, and stress-extruded wire.This option may be purchased with any new HVX tester, or added as an upgrade to any of your existing HVX testers.
-
Product
PXIe-2512, 7-Channel, 10 A PXI Signal Insertion Switch Module
780587-12
Signal Module
PXIe, 7-Channel, 10 A PXI Signal Insertion Switch Module—The PXIe‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
-
Product
PXIe-2514, 7-Channel, 40 A PXI Signal Insertion Switch Module
780587-14
Signal Module
PXIe, 7-Channel, 40 A PXI Signal Insertion Switch Module—The PXIe‑2514 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2514 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
-
Product
Standard Mechanical Calibration Kit, DC To 3 GHz, Type-N, 75 Ohm
85036B
Mechanical Calibration Kit
The Keysight 85036B calibration kit contains precision 75 ohm type-N standards used to calibrate Keysight network analyzers for measurement of devices with 75 ohm type-N connectors. Standards include fixed terminations, open circuits, and short circuits in both genders. This kit is specified from dc to 3 GHz.
-
Product
Time Domain Reflectometers
T3SP Series
-
Teledyne Test Tools T3SP15D stimulates the DUT with true differential signals. The T3SP15D offers fast rise times of 35 ps for spatial impedance resolution (in FR4) of 3 mm, at DUT lengths up to 40 meters and TDR repetition rates up to 10 MHz and uses the same open short load thru (OSLT) calibration standards as vector network analyzers. With their small form factors, light weight, and optional internal batteries, the instruments go anywhere in test labs or in the field at an affordable price.
-
Product
Multimeter Network Tester
VA16
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Network Cable test (RJ45): Tests for open circuits, shorts, miswires, reversals, and split pairs SHIELD detection tests a cabl
-
Product
Economy Mechanical Calibration Kit, DC To 3 GHz, Type-F, 75 Ohm
85039B
Mechanical Calibration Kit
The Keysight 85039B calibration kit, with option M0F, contains male and female type-F open, short, and load standards. This calibration kit works with all 75 ohm network analyzers and test sets for measurement of devices with 75 ohm type-F connectors. The kit also includes type-N to type-F adapters. More economical versions of this kit are available by ordering option 00F for the female standards only, or option 00M for the male standards only. This kit is specified from dc to 3 GHz.
-
Product
DCDC
JA/JP Series
-
The 15-Watt JA/JP series operates over an ultra wide range of 9-36 Vdc or 20-72 Vdc. Efficiencies of 80% are typical over varying load conditions of 25% to 100%. Additional features include input reverse polarity protection, remote on/off control, logic compatible with CMOS or open collector TTL, short circuit protection with auto restart, overvoltage protection, and an operating temperature range of -25°C to +71°C with no derating. Units are packaged in a six-sided continuous shielded case for EMI/RFI protection and measure 2.0” x 2.0” x 0.40”.
-
Product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 8 Channel
40-201-008
Fault Insertion Unit
This high bandwidth differential PXI fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
Cable Fault Locator
FaultCaster
-
Low Cost Full specification Professional Digital TDR Measures Distances to Open or Short Circuit Faults Extended Measuring Range to 2000m (6000ft) on all cable types Fast-Edge Step TDR technology for improved range & Resolution
-
Product
NEXTest 7
PK-2030/2032/2033/2036/2037/2038
-
NEXTest 7 is an advanced and unique tester in the market. It's designed to check and troubleshoot the pin connections of Display port & HDMI prior to installation on equipment. By using advanced technology to verify the integrity (20 pins + shield) of both display port and HDMI cables, especially for HDTV installation and DIY termination in the field, solving your cable testing need, unlink all of the other testers verify 9 circuits only. It checks for opens, shorts, miswires and intermittent faults in all conductors plus shield continuity, most tester only test for opens. It displays cable map results of both TX (near end) and RX (far end) on the main unit, either on testing before or after installation cables. User can easily read and determine the actual 21 pins configuration on main unit. It employs both auto and manual scanning of 21 wires. Tone Generator mode transmits two selectable tones on each pin for use with Net Probe (PR-06P) optional, enables one to quickly locate a cable. It's capable of testing up to 8 cables and locations at one time. NEXTest 7 especially features a self-learning mode to memorize cable pin out for testing large quantity standard or custom cables for PASS/FAIL a snap, makes testing quick and more efficient.
-
Product
LAN Check With Tone Generator
PH-01
-
The LANCHECK consists of two modular units, a tester and a remote terminator. The modular design enables the tester to be used for local loop-back testing of patch cable or remote testing of pre-installed premise wiring. The LANCHECK makes it easy to recognize opens and shorts within a cable as well as identify reversed and miswired cables. It can verify a cable up to 2,000 feet in length. Furthermore, it comes with shielded connectors, which enables the testing of shielded twisted pair (STP) cables. It also features convenient Auto Scanning and precision Manual Scanning modes.
-
Product
Transformer & Capacitor Testers
-
*Quick and easy check for opens or shorts on transformers before energizing*Provides clear indications of open circuits, short connections and confirmation that the test results are OK*Tests overhead, pad-mount and other distribution transformers*Tests the primary and secondary sides of de‑energized transformers without disconnecting*Helps prevent line workers from installing a fuse on a shorted transformer*Automatic self-test feature*Magnet holds the tester in place while testing
-
Product
Low Thermal Shorting Plug
34103A
Shorting Plug
Get a convenient and reliable short; ships only with the 34420A Micro Ohm Meter
-
Product
Calibration Short For Digital Multimeters
34172B
Calibration Short
The Keysight 34172B digital multimeter calibration short is a set of two shorts which provide a convenient and reliable method to apply a short to the input connectors of the multimeter. Terminals are made of low-thermal copper alloys to minimize thermally-induced voltages caused by dissimilar metals.
-
Product
PC-NET Cable Tester
PR-09
-
The PC-NET Cable Tester is a portable, stand-alone unit that provides an affordable way to quickly test PC, Network, Telco, Coax, USB and IEEE1394 cables for continuity and wiring configuration for any combination. Open, shorts, miswires and cross-connected wires are detected immediately. The interchangeable connectors boards offers flexibility and convenience easy to read LED instantly indicates good or faulty. The tester is suitable for use by computer dealers and computer hardware outlets.
-
Product
4-in-1 OSLT Mechanical Calibration Kit, DC To 9 GHz
85515A
Mechanical Calibration Kit
The 85515A 4-in-1 mechanical calibration module combines an open, short, load, and through in a compact unit. The product is small, easy to handle, and light weight. The through allows users to easily calibrate non-insertable devices, such as a cable or filter with female-female connectors. During the “thru” part of the calibration, the 85515A through can be used.
-
Product
Short Range
-
A standard-compliant wireless technology, optimized to fit short range connectivity, energy per bit and bandwidth requirements, is behind every network - regardless of its nature or purpose. With the growing importance of wireless sensor networks and the IoT, most electronic systems require wireless connectivity.
-
Product
Shorts
-
These coaxial shorts are useful to establish a reference plane, as well as providing certain protections from the environment. SMA shorts and Type N Shorts can establish reference planes. These coaxial shorts are not VNA grade but are often used at lower frequencies for calibration purposes. Included here are the following shorts: 2.4mm, 2.92mm, 2.2-5, BNC, N, SMA, SMB, SMP, SSMA, SSMC, TNC. Note, more options: 1.85mm is compatible with 2.4mm, 3.5mm is compatible with 2.92mm.
-
Product
Short Hot Stick
HS-120R
-
Standard Electric Works Co., Ltd
Weight: Approx. 885g. The Hot Stick is rated at 100kV per 300mm(5 minutes). High quality fiber glass round tube filled with Polyurethane. Meets IEC 60855. Reasonable price.
-
Product
Coaxial Short
85140B
Terminator
The Keysight 85140B coaxial short is used for establishing measurement planes for known reflection phase and magnitude in 50-ohm coaxial systems. It has a 2.4 mm female connector.
