CCTV Testers
See Also: CCTV
-
Product
Rust and Corrosion Testers
-
Liquefied petroleum gas copper corrosion tester, lubricating oil rust characteristics tester, rust characteristics and corrosion tester, copper strip corrosion tester
-
Product
SD Host Tester / SD / EMMC Analyzer / SD Card Tester
SGDK330B (SD / eMMC analyzer)
-
SGDK330B (SD / eMMC Analyzer) is a product that has the functions of SD Analyzer (SD Analyzer) and eMMC Analyzer (eMMC Analyzer).
-
Product
Drivetrain Tester
G5.DT
-
The G5.DT series is bidirectional regenerative. It was developed specifically for testing DC components of the electrical drive train or DC components of other parts of the vehicle electrical system. It is suitable for use in laboratories and on test benches. The modular and finely graded G5.DT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies are equipped with a powerful CAN multi-protocol interface (1 kHz, 16 bit) and optionally offer test bench relevant safety functions such as PL e according to EN ISO 13849, insulation monitoring as well as automatic discharge on the load side in case of shutdown.
-
Product
Cable Testers
DMX ADAPTER
-
DMX protocol is a standard means of controlling lighting dimmers remotely from a control desk. The standard uses a three wire connection using 5-pin XLR type connectors. These adapters allow the E445, E446 and E447 table testers to be used to test the primary circuit of such cables. Two adapters are required for each cable tester.
-
Product
Diode Tester
FEC200E
-
Frothingham Electronics Corporation
The FEC200E is an automatic computer- controlled diode and rectifier tester. It is controlled by a standard PC-compatible computer running FreeDOS.
-
Product
DataComm & LAN Testers
-
Tests & troubleshoots voice communication for open circuits, shorts, miswires, reversals, and split pairsSHIELD detection tests a cable’s shield integrityEasy to read fault display and high speed testingDebug mode for detailed fault identification resultsNetworking Cable Tester has auto sleep mode and power off switch to decrease power consumptionBattery low LED indicator
-
-
Product
Wristat Tester
WT 25-4145.26M
-
WT 25-4145.26M Wristat Tester is available to comply with D.O.D. 4145.26 specifications. The WT25-4145.26M Wristat Tester is designed to test the integrity of our WRISTAT in a fast, efficient, and simple manner. All the elements of the WRISTAT – continuity of the strap, integrity of the protective resistor, and satisfactory strap to skin contact – are easily confirmed by pressing the top cover of the WT25-4145.26M. The operator (wearer) is tested for a resistance to ground of greater than 250K ohms and less than1,200,000 ohms. The upper limit notifies you of an unacceptably high resistance value (IE possible loss of effective dissipation) and the lower limit warns of unsafe low resistance (possible risk of electric shock from surrounding motors, live wires etc.). The unit is not switchable.
-
Product
De-Energized Tester
MOTOR GENIE
-
The MOTOR GENIE® can see more than a megohmmeter, resistance tester, or RCL tester, making it the perfect tool for troubleshooting, startup, and quality control of low voltage AC induction motors.
-
Product
Combination Board Testers
QT2256-640 PXI
-
Qmax Test Technologies Pvt. Ltd.
designed as a Combination Board Tester capable of testing highly complex and dense PCBs employing various test techniques on a single platform. It can perform Board Level Functional Test through edge connectors of a PCB, and guided probe diagnostics utility to reliably repair Digital/Analog and Mixed Signal PCBs of various complexities for conventional PCBs.
-
Product
Manual PAT Testers
-
If you are looking for a manual PAT tester with a pass fail reading or a PAT tester with readings we have a solution for you. Carry out mains supply checks, IEC lead tests, Earth continuity tests at 200mA, Insulation resistance tests to 250V and 500V, and more with these popular testers. All of our manual PAT testers are available as kits to help you streamline the way you work.
-
Product
Battery Load Tester
Battery Beak
-
Cross the Road Electronics, LLC
The Battery Beak is a battery load tester that is capable of delivering an 18 amp load and measuring a batteries internal resistance, state of charge (SOC), and can determine the overall health of the battery. The Battery Beak supports all battery chemistries but has additional features to determine battery health for both Lead Acid and NiMH chemistries and supports a variety of AmpHour/Voltage combinations.
-
Product
Cable Tester & Cable Tracer & Multi-Functions Lan Tester
M-CT-430A
-
Fuzhou Metricu Technology Co Ltd
The multifunction LAN tester M-CT-430A is designed for maintenance and installation of cable, cable tracer, and HD Coaxial video level meter test in one equipment. The unit supports detect the near-end, mid-end and far-end fault point of RJ45 cable connector, and also supports Port Flash, PING test, IP address Scan, Link Monitor. Installers take the all in one cable tester, making working conditions safer and increasing productivity.
-
Product
Adapter for 980L-1A Tester
TA-331A
-
331A-9G HSI Adapter for use with the 980L-1A tester. Built to manufacturer's specs to allow by the book testing.
-
Product
Condensation Tester
-
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Condensation tester simulates the damaging effects of outdoor moisture attack by condensing warm water directly onto test specimens. In a few days or weeks, the tester can reproduce the damage due to moisture that occurs over months or years outdoors.
-
Product
Gas Permeability Tester
QT-GPT
-
Gas Permeability Tester- QT-GPT series is used to test the gas transmission rate (GTR) of packaging material by differential pressure method.
-
Product
Wire Mount Testers
-
Is designed to measure and control the DC resistance, electrical capacity, insulation resistance of electrical circuits and check the electrical insulation strength of electrical circuits.
-
Product
Waterproof pH Tester
pHTestr 10
-
Large Display Screen - dual display LCD for enhanced readability, provides comprehensive meter information
-
Product
Electrical Testers
-
Digital voltage and continuity tester with LCD screenAC and DC voltage testing (7 thresholds) with automatic AC or DC detection, audible continuity and single-pole phase test.
-
Product
Advanced Loss Tester
OLT-55
-
ated with Stabilized Laser Source, Optical Power Meter, Optical Loss Tester, ORL Tester and Length Testing functions. It can perform automatic bidirectional loss test on single fiber with Pass/Fail assessment. With rich functions, flexible configuration and excellent user friendly design, OLT-55 is the ideal optical loss tester to completely evaluate the optical fiber link condition in FTTx, LAN and CATV network.
-
Product
Distillation Testers
-
AUtomatic distillation apparatus, distillation tester, benzene disitillation tester (low temperature), vacuum distillation tester, distillation tester (double units), distillation tester (low temperature double units).
-
-
Product
Breakdown Voltage Tester
ZDS-50B
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-4; Inspection standard: JB/T4279.11-2008Used to test the breakdown voltage performance under room temperature of enameled round and flat wires with nominal conductor diameter of 0.018mm and above;Three voltage rise speeds are available: 20V/s, 100V/s and 500V/s, with error being ±5%;Three test methods can be adopted: round bar method, twist pair method and ball method;Clamp a group of test samples (5 for each) once, available to complete breakdown or withstand voltage test for any of sample one by one or individually; breakdown voltage and withstand voltage time would be automatically saved for future enquiry; all operations would be automatically completed;Capable of conducting high temperature breakdown voltage test in combination with RDS-50 thermal-state voltage tester;LED would automatically display test results and automatically return;During sample breakdown, breakdown voltage indication value would be automatically locked, free from flashing, and the test result is distinct and relatively clear;Equipped with test fixture for round rod method and twist pair method as well as the test weight for round rod method;Equipped with ball method test device (steel balls are prepared by user);Test door is provided with safety interlocking device, compliant with relevant regulations on high voltage testing equipment.
-
Product
LED Tester For Packaging Machine
-
LED-501 is a single crystal packing tester. It can be utilized in electrical test.Two test results. Pass (GO) or fail (NG).Electrical Testing: Forward：VF Reverse：VZ,IRFour-wire measurement and contact resistance in case of deviation.Auto polarity identification and preheat function.Provide OPEN\SHORT count.Compatible mechanical interface.Connected with computer for measurement data collection.
-
Product
Turns Ratio Testers
TRT Standard Series
-
When it comes to choosing a transformer turns ratio tester, TRT Standard series offers some of the most advanced instruments with LCD display out in the market. Each model measures transformer excitation current and phase shift performs automatic vector group detection and magnetic balance on three-phase transformers and three-phase autotransformers. Furthermore, they have a built-in true three-phase power source. Because of that, TRT Standard instruments can test transformers with special configurations, such as phase-shifting, rectifier, arc-furnace, traction transformers, etc.The instruments can output test voltages from 1 V AC to 250 V AC, depending on the chosen model. High test voltage of 250 V AC provides more accurate turns ratio testing compared to other turns ratio testers on the market and extremely low test voltage of 1 V AC enables turns ratio verification of current transformers.TRT Standard series consists of:TRT03 Models (TRT03A, TRT03B, TRT03C) – single-phase voltage up to 100 VTRT3x Models (TRT30A, TRT30B, TRT30C, TRT33A, TRT33B, TRT33C) – single and true three-phase voltage up to 100 VTRT63 Models (TRT63A, TRT63B, TRT63C) – single and true three-phase voltage up to 250 VMore about models differences can be found under the downloads tab, in brochures and comparison sheets.A user can create test templates using the DV Win software and store them in the PC’s memory for later use when in the field.TRT Standard series models have a built-in tap changer control unit. Consequently, it enables remote control of an on-load tap changer (OLTC) directly from the tester. In order to make the most out of this feature, the DV-Win software can be programmed to do everything automatically – running turns ratio tests, changing OLTC tap positions and saving results. This option, especially in combination with test templates, significantly facilitates and shortens the turns ratio testing time.
-
-
Product
Pocket Network Tester
LinkSprinter®
-
The LinkSprinter Pocket Network Tester verifies the functionality of copper Ethernet links and identifies errors in less than 10 seconds. The tester reveals network connectivity status and port information while ensuring documentation for every link. The comprehensive AutoTester measures PoE voltage, performs a switch test, and confirms the DHCP server is running and responsive. The tester also verifies gateway/router, internal IP service, and cloud reachability. When paired with the secure Link-Live Cloud Service, the Network Tester automatically uploads results and allows annotation of results enabling job supervisors to easily manage the progress of deployment and troubleshooting tasks assigned to their team.
-
Product
PV Accelerating Tester
-
King Design Industrial Co., Ltd.
*Spectrum mis-match: IEC 60904-9 class A*Non-uniformity <5%*Instability <5% ( within 30 mins)*Irradiance range: 800 W/m2 ~ 1200W/m2*Effective range: 30cm x 30cm; 1.1m x 1.4m*(customize accepatble)*Temperature：40℃ ~ 90℃*Humidity: 20% ~ 85%
-
Product
Appliance Testers
-
is a light-weight, portable appliance tester that tests the integrity of electrical devices. Developed for the commercial electrician or facilities maintenance persons to carry out a wide variety of safety measurements of electrical appliances.
-
Product
Tablet Hardness Testers
-
Teledyne LABS offers both manual and automated tablet hardness testers. Tablet hardness testing is a method of determining mechanical properties of a drug product, typically oral dosage forms such as a solid dose tablet. Tablet breaking force (commonly called tablet hardness) is a crucial characteristic in the manufacture of solid dose formulations. Tablet hardness testing is a major step in tablet consistency and quality control.
