-
product
PXI Single 46x4 Matrix, 1 Pole Switching
40-524-021
Medium density PXI dual 46x4, 1-pole matrix - it is also available inreed relay formats of 2-pole and 1-pole screened (see "also in this range" on right). The screened version is suitable for switching signals up to 50MHz. Typical applications include signal routing in ATE and data acquisition systems. The two banks may be used for operating a 4-wire measurement system (bank-1 for source, bank-2 for measure). Larger matrices may be constructed by daisy chaining the common signals from multiple PXI Modules.
-
product
PXI-2515, 35-Channel, 0.25 A PXI Signal Insertion Switch Module
778572-15
35-Channel, 0.25 A PXI Signal Insertion Switch Module—The PXI‑2515 is a multiplexer switch module that enables connectivity by routing high-speed digital I/O (DIO) signals between a device under test (DUT) and an NI high-speed DIO device or a parametric measurement device. You can use modules such as PXI Source Measure Units (SMUs) and PXI Digital Multimeters (DMMs) with high-speed digital devices. With the PXI‑2515, you can perform parametric tests on digital pins without external connectivity or impedance mismatch challenges.
-
product
GENASYS High Density Matrix Switch Card, 104 X 8 X 8
GX6188 Series
The GX6188 is a 6U PXI, high density matrix, GENASYS architecture switching card. The card provides the user with the ability to connect and interface resources to multiple UUT connections. The board consists of two matrices - a 104x8 and a 8x8 matrix. The GX6188 can connect to 104 UUT switching points, eight external resources and an eight channel global bus via front panel connectors. Multiple GX6188 cards can be connected using the global bus. Like other GENASYS switch cards, the GX6188 features an integral, 3-dimensional switching architecture which provides the flexibility to connect test system resources to multiple UUT connections as well as supporting an expansion bus connection without sacrificing I/O matrix connections when building multiple switch card configurations.
-
product
Vacuity Testers Of Vacuum Switches
GDZK-IV
GDZK-IV Vacuity Testers of Vacuum Switches is designed to measure the vacuum degree of vacuum switches. It uses an electromagnetic discharge measuring method, to ensure the testing results accurate and reliable.The testing data can estimate vacuum switch's health and life span
-
product
Optical Fiber 4×1 Switch
OFSW - 4 × 1
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW-4×1 is a 4×1 prism optical switch. It can support 4 optical fibers input and 1 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
product
Static Switches
Static, or solid-state, switches are electronic devices for switching and driving resistors that provide a longer service life than electromechanical relays. Static switches are used to control high-power motors, transformers, tungsten lamps, heating elements and in many of the difficult and heavy-duty applications typical of industries using electric ovens, in the glass and plastics industries.
-
product
PXI-2555, 2.5 GHz, 75 Ω, Terminated 4x1 PXI RF Multiplexer Switch Module
778572-55
2.5 GHz, 75 Ω, Terminated 4x1 PXI RF Multiplexer Switch Module—The PXI‑2555 is an RF signal multiplexer switch module. The internal termination of the PXI‑2555, which helps prevent high-power reflections that arise from open channels on the module, makes it ideal for use in video RF applications where such reflections can damage the source. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use the onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
PXI Dual 32x4 Matrix 2-Pole Switching
40-534A-022
Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability sputtered Ruthenium reed relays, offering >109operations to give maximum switching confidence with long life and stable contact resistance. Larger matrices may be constructed by daisy chaining the common signals from multiple PXI modules.
-
product
Fiber Optical Switch at Single Mode Latching 1310/1550nm 5V with LC/PC Connector
SUN-FSW-1x1
Guilin GLsun Science and Tech Group Co., LTD
GLSUN 1×1 fiber optic switch -Features·Low Insertion Loss·High Stability, High Reliability·Low Crosstalk·Wide Wavelength Range·Epoxy-free on Optical Path·Latching and Non-latchingGLSUN 1×1 fiber optic switch -Applications·System Monitoring·OADM·R&D in Laboratory·MAN (Metropolitan Area Network)·Network Security and MonitoringGLSUN 1×1 fiber optic switch - SpecificationsParameters Unit SUN-FSW-1×1Wavelength Range nm 850±40 / 1300±40 1260 ~ 1650Test Wavelength nm 850 / 1300 1310 / 1550Insertion Loss 1,2 dB Typ: 0.5 Max: 0.8 Typ: 0.4 Max: 0.6Return Loss 1, 2 dB MM ≥ 30 SM ≥ 50Crosstalk 1 dB MM ≥ 65 SM ≥ 70PDL dB ≤0.05WDL dB ≤0.25Repeatability dB ≤±0.02Operating Voltage V 3.0 or 5.0Durability Cycles ≥ 10 MillionSwitching Time ms ≤8Optical Power mW ≤500Operating Temperature ℃ -20 ~ +70Storage Temperature ℃ -40 ~ +85Relative Humidity % 5 ~ 95Weight g 14Dimension mm (L)27.0×(W)12.6×(H)8.2 ±0.2Note: 1 Within operating temperature and SOP.2 Excluding Connectors.
-
product
Physical Layer Switching Systems for copper LAN, WAN, DSL, Telco apps with RJ style connectors.
RJ Series
The RJ Series of computer controlled switching systems are designed for physical layer switching of multiwire signals on RJ style connectors. Since the system uses mechanical relays it acts exactly like a piece of cable which makes it perfect for testing networks without altering the signals or regeneration. These systems are typically used for Ethernet LAN 10BaseT through 1000BaseT, DSL including ASML through GFAST, CAT5 through CAT6A cable testing, USB up to 2.0, RS232, RS422, RS485 up to 8 wire at 20 Mbps and many other applications switched over RJ45 connectors up to 8 wires. They may also be used as lab automation switches, network testing switches, patch panels, network redundancy switches or any number of physical layer applications.
-
product
PXI-2593, 500 MHz, 50 Ω PXI RF Multiplexer Switch Module
778793-01
500 MHz, 50 Ω PXI RF Multiplexer Switch Module—The PXI‑2593 can be programmatically configured as unterminated multiplexers, externally terminated multiplexers, or dimensionally flexible sparse matrices.
-
product
6U cPCI 1/10/40 GbE Switch
ComEth4050e
The ComEth 4050e is a cutting-edge 6U cPCI Layer 2/3 Ethernet switch for PICMG 2.16 & VITA 31.1 systems and is powered by the newest Marvell highly integrated system-on-chip (SoC) with programmable packet processors.
-
product
Single Bus 36-Channel 2A PCI Fault Insertion Switch
50-190-201
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
Loop and Line Powered Level Switch
Safety IntelliPoint
The Safety IntelliPoint level switch provides a capacitance probe level switch with either a current output or relay contacts and “On-Board” self-diagnostics to ensure reliability. This SIL Intellipoint conforms to SIL 2 specifications providing the ultimate in level switch integrity and level sensing elements for a wide variety of temperatures, pressures, and materials.
-
product
LXI Scalable Switched Guard Matrix - 16x16 Plugin Module
65-290-001
The 65-290-001 ia a 16x16 matrix plug-in module for use in Pickering's modular switching platform that provides a switched guard relay matrix solution with up to 1012 Ω channel to channel and channel to ground isolation.
-
product
PXI 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
40-205-008
The 40-205-008 (PXI) is an 8-channel fault insertion switch designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. It is available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
product
OEM Pressure Switch
A1PS
Series A1PS/A1VS Economical Pressure Switches are designed with a 15 Amp SPDT switch for direct control of pumps and motors. Available in pressure, vacuum, or compound ranges, the switches offer a field adjustable set point.
-
product
AXIe PDC Switch
The AXIe CCP module implements a 32x16 matrix switcher structure (32 inputs – 16 outputs). KCP is an indispensable module for use as part of combined systems for checking the parameters of radio-electronic units.
-
product
PXI-2514, 7-Channel, 40 A PXI Signal Insertion Switch Module
778572-14
7-Channel, 40 A PXI Signal Insertion Switch Module—The PXI‑2514 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2514 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
product
High Power, Low PIM Switch Unit
LPSU
Low PIM coaxial switch matrix 5 x 6 or 1 x 4 configurationFrequency range 698-2700 MHz.SCPI commands via Ethernet (wired or wireless).Significantly reduces test time for multi frequency PIM applications.Applications: ATE systems, multi-band antenna and component testing.
-
product
Programmable Limit Switch
PLS1000
Computer Conversions Corporation
The PLS1000 is a programmable limit switch designed to allow convenient programming of 16 circuits.The PLS1000 is designed to be panel mounted.
-
product
12 Port CPCI Managed Layer Two Switch
CP219
The CP219 is a 3U single slot Compact PCI (cPCI) module that has 12 Ports of 10/100/1000 GbE. The Module has the option for two Ports on its P2 Connector.
-
product
VME & Mezzanine Switches & Routers
Curtiss-Wright Defense Solutions
Our VME and mezzanine switches and routers provide systems integrators with a fast and powerful way to interconnect chassis, cards, and processors through switched Gigabit Ethernet links. Operating at wire-speed, these networking modules can be used to architect a network-centric infrastructure for advanced military systems.
-
product
Speed Switch Sensor & System Testing Device
The SpeedMaster with Pulse Pilot provides independent, real time, and complete verification of an entire speed monitoring system to ensure that alarms and shutdowns are working as expected.
-
product
PXI Switched Guard Reed Relay Module, 26x SPST
40-121-001
The 40-121-001 provides 26x SPST switches in a single slot PXI module and designed to provide an isolation resistance in excess of 1013Ω. It has been designed to ensure high isolation resistance through the use of switched guards, making it ideal for low level measurements and semiconductor test.
-
product
Liquid Level Switch
CL-10GH
The Dynatrol® CL-10GH Liquid Level Detector and EC-501A(G) Control Unit is used for high, intermediate or low point level detection of liquids and slurries. A unique vibrating principle permits design and operation features not available with other types of liquid level detectors.
-
product
ATC Cabinet Switch Pack Tester
ASPT-5300
The ASPT-5300 ATC Cabinet Switch Pack Tester (HV) will run a series of comprehensive tests on the Model 2202-HV HDSP/FU. The Model 2202-HV HDSP/FU is an important component in the ATC Cabinet Monitoring System.The Model 2202-HV HDSP/FU not only provides field output drivers, but also monitors the voltage and current for each of the field outputs.
-
product
Low PIM Coaxial Switch, DC to 4 GHz, SP4T
87104P
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87104P is a low PIM SP4T coaxial switch, operating from DC to 4 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
product
PXI Differential Fault Insertion Switch Modules
Pickering's PXI Differential Fault Insertion Switch Modules support multiple channels of two-wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to externally applied fault conditions. *Two module types are available: Two wire fault insertion module suitable for CAN Bus and FlexRay.*High bandwidth two wire fault insertion module suitable for Gigabit Ethernet, AFDX and BroadR-Reach.
-
product
USB Programmable SPDT and SP4T Solid State RF and Microwave Switches
LSW Series
The Lab Brick LSW Series RF and Microwave Switch product family offers reliable, high isolation and low cost solid state switch products in both single pole double throw and single pole four throw configurations. These units require connection to a USB port for control and power. No additional DC supply voltage is required. Lab Brick RF and Microwave Switches are easily controlled and programmed directly from the included GUI and through the external control inputs. Lab Brick Switch API DLL and LabVIEW compatible drivers are also available for custom programming applications.
