Frame Relay
-
product
PXI Switched Guard Reed Relay Module, 13x SPST
40-121-002
The 40-121-002 provides 13x SPST switches in a single slot PXI module and designed to provide an isolation resistance in excess of 1013Ω. It has been designed to ensure high isolation resistance through the use of switched guards, making it ideal for low level measurements and semiconductor test.
-
product
PXI 48 x SPDT Power Relay Module
45-157-001
The 45-157 SPDT Power Relay Module consists of 48 single pole changeover relays controlled by a PXI/CompactPCI interface. It is suitable for applications were conventional reed-relay based switching modules do not have sufficient voltage rating or current carrying capacity. All 48 contacts are electrically isolated from each other and are capable of switching resistive and inductive loads up to 2000VA at 240V AC.
-
product
PXI 16 Trib Daisy Chain Switch Balanced 96 W
40-796-001
The 40-795/796 Daisy Chain Switching Module is designed for telecom test applications. It allows production or verification testing of SONET/SDH transmission multiplexers switching 2MBit/s or 1.5MBit/s data over 100 or 120 balanced lines.
-
product
PXI/PXIe RF Switch, Triple SPDT, 3GHz, 50Ω, MCX
40-870A-103
The 40-870A-103 (PXI) and 42-870A-103 (PXIe) are 50Ω RF switches with 3 separate SPDT relays in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The injection of noise and unwanted signals into the signal paths of the 40/42-870A has been minimized by careful attention to the mechanical and electrical design.
-
product
High Current Relay PXI Card
GX6115
The GX6115 is a 15 channel, high current relay board that plugs directly into any 3U PXI slot. The GX6115 also provides three transistor-driven channels for external relays. These outputs may be used to drive external loads, such as heavy duty relays, lamps or other devices.
-
product
PXI Dual Microwave SPDT Relay 18GHz 50 SMA - External Termination
40-781-122
The 40-781 Microwave switching module consists of one, or two changeover switches capable of switching frequencies to 18GHz in 50 Ohm. Versions are available with either internal or external terminations and connections are made via front panel mounted high quality SMA RF coaxial connectors.
-
product
PXI/PXIe Microwave Relay, Dual SPDT, 40GHz, 50Ω, SMA-2.9
40-780B-542
The 40-780B-542 (PXI) and 42-780B-542 (PXIe) are dual SPDT 40GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
product
PXI/PXIe Microwave Relay, Dual SPDT, 67GHz, 50Ω, SMA-1.85
40-780B-572
The 40-780B-572 (PXI) and 42-780B-572 (PXIe) are dual SPDT 67GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions.
-
product
32-Ch SPDT 2A-240VAC 24VDC Switching
YAV90133
32 relays, 5A Switching 5A 250Vac. Up to 1250VA 28 Relays SPST Mux. 1 a 4 relays CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
PXIe Microwave Relay, Dual SPDT, 26.5 GHz, 50 Ω, SMA, Failsafe
42-780B-532
The 40-780B-532 (PXI) and 42-780B-532 (PXIe) are dual failsafe SPDT 26.5 GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
product
CL PX4 SE Frame Grabber
Xcelera-CL PX4 SE
The X64 Xcelera-CL PX4 SE is a highly versatile PCIe frame grabber capable for one Camera Link™ Base, Medium, or Full camera and performing image transfers at rates up to 1024MB/s. Its low cost, combined with its ability to support multiple tap configurations from area and linescan monochrome/RGB cameras simultaneously; in addition to its onboard FPGA Bayer decoding and real-time shading correction makes the X64 Xcelera-CL PX4 SE an ideal solution to a wide variety of cost-sensitive applications.
-
product
PXI 16x SPST High Voltage Reed Relays
40-310-101
The 40-310/320 Range of High Voltage Switching Modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications for the 40-310/320 series modules include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
product
LXI Reed Relay Matrix - Dual 32x16 Plugin, No Direct Y Access, 3 Analog Buses
65-225-101
These Modular LXI Matrix Reed Relay Matrix Modules plug into our LXI Modular Chassis (model 65-200-002)—providing access to all signal connection on 200 pin connectors. They are constructed using Pickering Electronics' Reed Relays offering maximum performance and reliability as well as very fast operate times.
-
product
SIMRC - 16 x Uncommitted Reed Relay, SPDT
1010-R-16-1-5/3D
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
product
PXI Single Microwave SPDT Relay 2.5GHz 75 1.6/5.6
40-780A-751
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
product
PCI 32xSPDT Shielded Reed Relay Card
50-120-021
This of PCI switching cards are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female connector.
-
product
SWB-2834, 8x34, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781421-34
8x34, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2834 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
64-Ch SPDT 2A-240VAC 24VDC Switching
YAV90164
64 relays SPDT, 2A Switching 2A 250Vac. Up to 62,5VA CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
CMOS Drive High Voltage SIL Reed Relays for up to 3 kilovolts
Series 101
Direct drive from 74HC/HCT Cmos SIL Relay. Dry or Mercury Wetted switches. 5 Volt coil for 1A dry version is 1600 0r 3000 Ohms
-
product
LXI Reed Relay Matrix - Dual 128x4 Plugin, No Direct Y Access, 12 Analog Buses
65-221-101
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
product
PXI-2568, 31-Channel, 2 A, SPST PXI Relay Module
778572-68
31-Channel, 2 A, SPST PXI Relay Module—The PXI‑2568 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2568 is fully software programmable. With an efficient coupling of voltage/current capability and relay density, this switch module is ideal for automated test equipment (ATE) loads or for controlling heaters, lights, and fans.
-
product
PXI Dual Microwave SPDT Relay 18GHz 50 SMA
40-780A-522
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
product
PCI 32xSPST Shielded Reed Relay Card
50-125-021
The 50-110/115 range of PCI shielded switching cards are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female connector.
-
product
PXI Power Relay Module, 6xSPDT, 16 A
40-161A-102
The 40/42-161A-102 is a PXI/PXIe 6xSPDT power relay module and is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock. Electro-mechanical power relays are used wich are suitable for switching loads up to 16 A at 250 VAC.
-
product
PXI Microwave Relay, Triple SPDT, 26.5GHz, 50Ω, SMA
40-780B-533
The 40-780B-533 (PXI) and 42-780B-533 (PXIe) are triple SPDT 26.5GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
product
SWB-2815, 4x86, 0.3 A, No Row Access, Reed Relay Matrix Module for SwitchBlock
781421-15
4x86, 0.3 A, No Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2815 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
PXIe Microwave Relay, Single SPDT, 26.5 GHz, 50 Ω, SMA, External Termination, Failsafe
42-781A-321
The 40-781A-321 (PXI) and 42-781A-321 (PXIe) are single failsafe SPDT 26.5 GHz microwave relay modules with external terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
product
PXI/PXIe Microwave Relay, Single SPDT, 50 GHz, 50 Ω, SMA-2.4, Remote Mount, Failsafe
42-780B-551-E
The 40-780B-551-E (PXI) and 42-780B-551-E (PXIe) are single failsafe SPDT 50 GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
product
PXI Power Relay Module, 10xSPST, 16 A, With Interlock
40-161A-003-HI
The 40/42-161A-003-HI is a PXI/PXIe 10xSPST power relay modulewith optional hardware interlock. It is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock.
-
product
83x SPDT High-Density PXI Relay Module
40-100-001
Configured with 83 SPDT relays, this high-density 2 Amp PXI Relay module was originally designed for applications in Aerospace and Defense requiring a higher density 2 Amp alternative to our current 52 SPDT module (model 40-139). This new Relay Module is suitable for applications requiring medium power switching with very high density. It features a 2 Amp current capacity and voltages to 200VDC/140VAC.
