Pyroelectric Sensors
Turn absorbed radiant energy into a current or voltage.
See Also: Thermopile Sensors
-
product
S2 Blinx Digital Sensors
ULP-S2 BLINX
The Universal LightProbe S2 Blinx Digital is designed for the simple ON/OFF test of any color blinking or steady-state LED, for fast results with a digital output. The Universal LightProbe S2 Blinx Digital Sensors check the ON/OFF status of any color LED, whether stable or blinking/pulsed, up to a rate of 15 Hz, and provide a Logic “1” output (5 volts) only if the LED is “ON” and a Logic “0” if the LED is “OFF.”Operating temperature range: 0oC to 70oCPower consumption: Operates from +5, 12, 24 or 28 volts D.C., at 6mA max.Voltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Load: 20mA max. (Source/Sink). Non-inductiveOutput Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times: <66mS, shorter for brighter LEDsFiber-Optic Probes: Wide Aperture Fiber-Optic Probe recomended
-
product
Volkswagen Oxygen Sensor
KS60113 - Volkswagen
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
Light-to-Digital Proximity Sensors
Renesas' light-to-digital proximity sensors offer low light sensitivity, superior proximity range performance, low power consumption, easy to use simple output algorithm, and an array of other features including intelligent interrupt, sleep modes and Time of Flight (ToF) signal processing.
-
product
Analog Seismic Sensors
Seismometers
Designed to yield the performance needed for scientific studies, our seismometers are used for monitoring long period (very low frequency) signals. These units are often used for earthquake monitoring and for triggering potential alerts during natural disasters such as tsunamis.
-
product
Uncooled Infrared Cameras and Sensors
Uncooled Infrared Cameras and Sensors by Lynred USA: XGA/SXGA Format, VGA Format, QVGA Format
-
product
Antenna, Loop Sensor
EM-6873 | 20 Hz – 100 KHz
The EM-6873 Loop Sensor Antenna uses passive circuits to transform magnetic field components between 20 Hz – 100 kHz to an equivalent open circuit two-terminal voltage on the receiving instrument. Use of the conversion Factor Chart, supplied with each antenna, will yield the strength of the magnetic induction field referenced to a uniform field. The loop is electrostatically shielded and therefore is sensitive only to the magnetic component (B-field) of the electromagnetic fields.
-
product
Charge Logger Sensor
NUL-246
This sensor measures electrostatic charges. It can be seen as a highly sensitive electroscope indicating whether a charge is positive or negative. Other uses are: to explore the nature of static charge, to measure both charge and voltage, to measure charge by induction, quantify the charge on a capacitor or discover the charge distribution on a conducting sphere.
-
product
Compact Micro-size Inductive Proximity Sensor
GS
Panasonic Industrial Devices Sales Company of America
The Panasonic GS Compact Micro-size Inductive Proximity Sensor has Sensor heads that come in multiple sizes with a separate amplifier controller.
-
product
Measurement Sensors For Network Analyzers And Recorders
Measurement sensors for network analyzers and recorders
-
product
Power Sensors
N8480 Series
N8480 thermocouple power sensors, integrated with EEPROM capability, are the latest RF sensor applications with excellent measurement accuracy, repeatability, and linearity.
-
product
Inductive Sensor
HFCT Ø 30-39-50mm
Techimp HFCT is an inductive sensor for partial discharge measurements. It is suitable for on/off line PD tests on many electrical systems (cables, transformers, rotating machine, etc..). It has to be applied to the ground connection of the system to be tested.
-
product
Capacitive Sensors
capaNCDT
Capacitive sensors are designed for non-contact measurement of displacement, distance and position, as well as for thickness measurement. Due to their high signal stability and resolution, capacitive displacement sensors are applied in laboratories and industrial measurement tasks. In production control, for example, capacitive sensors measure film thickness and application of the adhesive. Installed in machines, they monitor displacement and tool positions.
-
product
CO₂ Humidity And Temperature Sensor
SCD40 (Qwiic)
The SCD40 from Sensirion is a high quality Photoacoustic based CO₂ sensor capable of detecting 0 to 40000ppm with the best accuracy over 400-2000ppm ±(40ppm+5%). In order to improve accuracy the SCD40 has integrated temperature and humidity sensing built-in. For additional accuracy the SCD40 also accepts ambient pressure readings!
-
-
product
Power Sensor and SNS Noise Source Cable (1.5m / 5 feet)
11730A
The Keysight 11730 series power sensor cables are used with the 8480 and E-series power sensors (except the E9320 family of peak and average sensors). These cables are designed to reduce RFI effects on low power readings with an improved shielding design in the cable itself. Cables may be ordered individually or in pairs in any combination desired for single and dual-channel measurements.
-
product
Sensor Solutions for IoT
Imec is a reference in the design of ultra-low power electronics, low-power algorithms to increase intelligence and data security, and in all aspects of data science. Our multi-sensor environmental monitoring platform features sensors for temperature, relative humidity, NO2, CO2, VOC (volatile organic compounds), particle matter, ambient light, sound, vibrations and presence detection. Our test platform is suitable for indoor and outdoor air quality monitoring and control, and can be used in smart buildings, smart cities and more.
-
product
Micro Sensor
MIC 1000-20
Advanced Thermal Solutions, Inc.
The MIC 1000-20 micro sensor is designed for measuring fluid velocity and temperature in areas that are densely packed. It can be used where the space between boards is less than 4 mm. The thickest part of the MIC 1000 is just 3.2 mm.
-
product
Hall Sensor Board with I2C Interface
048-368
Version: +5V/60A +5V/60A +3,3V/25A +12V/25A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
product
Printed Electronics & Printed Sensors
The first membrane switch was developed and produced in 1978 using printed electronics. Conductive pastes can now also be printed on substrates such as paper, textiles, or metal in addition to polyester. Our functional foils and printed electronics enable compact, and extremely efficient electronic products that are used in every industry. Processing intelligent pastes that have various physical properties enable the production of new and innovative applications in minimized form factors without the use of additional, highly complex electronic components.
-
product
Temperature Measurement IR Sensors & Detectors
ST150 With Diffractive Lens
A single-channel silicon-based thermopile with integrated diffractive lens and internal baffle that delivers a very low Temperature Coefficient of Responsivity of -0.04%/C with a high output voltage, 19.5 FOV and a quick time constant of 38ms. This Low-cost detector comes in a TO-5 package and has a very short thermal shock response to ambient temperature change.
-
product
Cryogenic Temperature Sensors
Thermocouple wire
Thermocouple wire is used in a variety of cryogenic applications, but special techniques must be employed to approach temperature accuracies of 1% of temperature, even without consideration for the effects of high magnetic fields or high radiation fluxes. The problems are further complicated by exposure to variable gradient conditions at cryogenic temperatures.
-
product
Low Torque Reaction Sensors
MTX
The MTX is a low torque sensor designed for calibrating and testing small hand screwdrivers, torque wrenches and power tools. With its low profile design, the calibration instrument can be used for automated applications, by mounting it to a palletized system. This saves time as there is need to remove the driver from the robot or off the automated system for calibration. These versatile torque sensors are used in conjunction with a torque tester.
-
product
Sensors
We design, develop and produce state-of-the-art SIGINT sensors that seek, exploit, identify, and locate sources of RF energy, underwater sound, light, heat and other complex phenomena. These sensors recognize threats, gather intelligence, and allow our customers to make informed, strategic response decisions.
-
product
SparkFun Triad Spectroscopy Sensor
AS7265x (Qwiic)
The SparkFun Triad Spectroscopy Sensor is a powerful optical inspection sensor also known as a spectrophotometer. Three AS7265x spectral sensors are combined alongside a visible, UV, and IR LEDs to illuminate and test various surfaces for light spectroscopy. The Triad is made up of three sensors; the AS72651, the AS72652, and the AS72653 and can detect the light from 410nm (UV) to 940nm (IR). In addition, 18 individual light frequencies can be measured with precision down to 28.6 nW/cm2 and accuracy of +/-12%. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
product
GEO Instruments & Sensors
Jewell Instruments divides its Geo tiltmeters into eight different series based on model numbers.
-
product
Environmental Sensors
Various Environmental Sensors including Room, Ceiling, Radiation and Contacting Temperature Sensor
-
product
Motion and Sensor Additional Instruments
Our expansive line of Trig-TekTM motion and sensor instruments offers a myriad of test and measurement functionality.
-
product
Inductive Proximity Sensors (Square)
SP2
Easy installation, high-speed pulse generator, high-speed rotation control, and more. A wealth of models ideal for limit control, counting control, and other applications. Sensing distance from 1~2/2 ~ 6/ 5~ 12/10~15mm. Housing by PBT with strong structure and acid resisting available.
-
product
Fiber Optic Temperature Sensor with the EasyDisk
The TPT-62
The TPT-62 fiber-optic temperature probe family employs industry standard 62.5µm core OM1 fiber optic for highly improved optical, mechanical, and reliability properties over legacy 200 µm core (1st generation) fiber optic sensors. The EasyDisk sensor tip assembly ensures IEC60076-2 (Annex E) compliant installation and enables quick insertion of the probes into the spacers within the windings of transformers.
-
product
Soil Moisture, Temperature, and EC Sensors
Soil volumetric water content probes (sometimes referred to as soil moisture sensors) measure the water content of soil. These probes can be used to estimate the amount of stored water in a profile or how much irrigation is required to reach a desired amount of water in the soil. These probes can be used for quick measurements or installed for long-term measurements.
