Showing results: 751 - 765 of 805 items found.
-
N1055A -
Keysight Technologies
Bandwidth options: 35 or 50 GHz (upgradable)Edge speed (10-90%, typical): 18 ps (35 GHz) or 7 ps (50 GHz)Channel options: 2 or 4 per module (upgradable) with independent skew control and up to 16 channels per 86100D mainframe Ultra-thin remote head: 1.6 m phase-stable cable, 2.92 mm (35 GHz) or 1.85 mm (50 GHz) connectors, and integrated 67 GHz diode limiters for ESD/EOS protection TDR fixture de-embedding removes effects of fixtures, cables or probes connected between remote heads and DUT
-
J7204A -
Keysight Technologies
The J7204A is a multi-channel (4-channels) attenuation solution for signal attenuation and conditioning of up to 4 devices under test (DUT). Operating frequency from DC to 6 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7204A reduces cost of ownership and provide the best measurement accuracy.
-
M8195A -
Keysight Technologies
Sample rate up to 65 GSa/s High channel density: 1, 2 or 4 channels per module, synchronization of up to 16 channels on 4 modules with the M8197A multi-channel synchronization module Built-in frequency and phase response calibration Embedded DSP enables real-time waveform and impairment generation(in conjunction with the 81195A optical modulation generator software)
-
E4412A -
Keysight Technologies
Fast measurement speed, up to 400 readings per second with the E4416AWide dynamic range (-70 dBm to +20 dBm)Calibration factors, linearity ana temperature compensations data stored in EEPROM Excellent SWR for reducing mismatch uncertainty Accurate calibration and traceability to NIST Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters
-
N1911A -
Keysight Technologies
30 MHz video bandwidth Single shot real time capture at 100 M sample/s per second Key Measurements: - peak, average, peak-to-average ratio, rise time, fall time and pulse width22 Predefined formats: WiMAX, DME, HSDPA, etc. One screen view for pulse measurement analysis: Auto Scale, Auto Gate, Rise/Fall Time, Duty Cycle, etc. Internal Zeroing and Calibration while connecting to the DUT Bench Vue software enabled
-
N4952A -
Keysight Technologies
The N4952A is an affordable and compact error detector remote head available in 4 to 17 Gb/s and 5 to 32 Gb/s configurations. Compatible with the N4960A Serial BERT controller, it is the perfect solution to test up to 32 Gb/s per channel for 100 Gigabit Ethernet applications and other high-data rate devices. The N4952A error detector supports PRBS or user patterns and operates up to 32 Gb/s in a single band with no gaps or missing data rates. The remote head allows the test equipment to be located very close to the device under test, eliminating the need for long cables that degrade signal quality.
-
787074-01 -
NI
The acA3088-57um is a Monochrome Basler Ace USB3 Vision Camera with a 6 MP resolution and a maximum image acquisition speed of 57 frames per second. … The acA3088-57um uses a IMX178 sensor and is quality tested and calibrated for high performance and reliability. This camera can be used with NI hardware and software to build machine vision systems.
-
787075-01 -
NI
The acA4024-29um is a Monochrome Basler Ace USB3 Vision Camera with a 12 MP resolution and a maximum image acquisition speed of 29 frames per second. … The acA4024-29um uses a IMX226 sensor and is quality tested and calibrated for high performance and reliability. This camera can be used with NI hardware and software to build machine vision systems.
-
787067-01 -
NI
The acA4024-8gm is a Monochrome Basler Ace GigE Vision Camera with a 12 MP resolution and a maximum image acquisition speed of 8 frames per second. … The acA4024-8gm uses a IMX226 sensor and is quality tested and calibrated for high performance and reliability. This camera can be used with NI hardware and software to build machine vision systems.
-
785908-01 -
NI
The acA2040-120um is a Monochrome Basler Ace USB3 Vision Camera with a 3 MP resolution and a maximum image acquisition speed of 120 frames per second. … The acA2040-120um uses a IMX252 sensor and is quality tested and calibrated for high performance and reliability. This camera can be used with NI hardware and software to build machine vision systems.
-
785910-01 -
NI
The acA2440-20gm is a Monochrome Basler Ace GigE Vision Camera with a 5 MP resolution and a maximum image acquisition speed of 20 frames per second. … The acA2440-20gm uses a IMX264 sensor and is quality tested and calibrated for high performance and reliability. This camera can be used with NI hardware and software to build machine vision systems.
-
785914-01 -
NI
The acA2040-35gm is a Monochrome Basler Ace GigE Vision Camera with a 3 MP resolution and a maximum image acquisition speed of 35 frames per second. … The acA2040-35gm uses a IMX265 sensor and is quality tested and calibrated for high performance and reliability. This camera can be used with NI hardware and software to build machine vision systems.
-
787069-01 -
NI
The acA1440-220uc is a Color Basler Ace USB3 Vision Camera with a 1.6 MP resolution and a maximum image acquisition speed of 220 frames per second. The acA1440-220uc uses a IMX273 sensor and is quality tested and calibrated for high performance and reliability. This camera can be used with NI hardware and software to build machine vision systems.
-
787068-01 -
NI
The acA720-520uc is a Color Basler Ace USB3 Vision Camera with a 0.3 MP resolution and a maximum image acquisition speed of 520 frames per second. The acA720-520uc uses a IMX287 sensor and is quality tested and calibrated for high performance and reliability. This camera can be used with NI hardware and software to build machine vision systems.
-
787071-01 -
NI
The acA4024-29uc is a Color Basler Ace USB3 Vision Camera with a 12 MP resolution and a maximum image acquisition speed of 29 frames per second. The acA4024-29uc uses a IMX226 sensor and is quality tested and calibrated for high performance and reliability. This camera can be used with NI hardware and software to build machine vision systems.