Interfaces
connections between dissimilar environments.
See Also: Serial Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Adapters, Interconnects
-
product
CAN Sensor/ Interface
Current
Reach Technologies’ CAN Current Sensors sense and digitize conductor current for collection via CAN. The module is ideal for conveniently adding current data to a distributed CAN network. The CAN Current Sensor is configurable via J1939 or CANopen stacks, and are available in Hall Effect and shunt variants.
-
product
Terminal Equipment Simulator
AI-5620
The AI-5620 simulates a single port two wire analog TE (Terminal Equipment) or CPE (Customer Premise Equipment) device. It is designed to measure and analyze signals generated by a CO (central office) line card, VoIP terminal adapter FXS port, or any device utilizing a SLIC (subscriber line interface circuit).
-
product
8-Channel 250 MHz A/D with Multiband DDC, Kintex UltraScale FPGA - PCIe
Model 78132
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Eight 250 MHz 16-bit A/Ds- Eight wideband DDCs (digital downconverters)- 64 multiband DDCs- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express (Gen. 1, 2, &3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized version available
-
product
ARINC PCI Express 4 Lane Interface Cards
PCIE4L-A429
Alta Data Technologies’ PCIE4L-A429 interface module offers a variety of ARINC-419/429/575/573/717 channel configurations with software selectable RX/Tx channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB). Encode or decode almost any ARINC-429 physical layer signal. The 4 lane card (PCIE4L) is normal 1/2 height common for most desktop and larger server systems.
-
product
Interface Converter
ZET 7177
ZET 7177 CAN→GSM interface converter can be used under conditions when there is no access to a regular connection over Ethernet, or when you need to provide a redundant channel in case of Ethernet fouling.
-
product
Serial RS-232 Expansion Connector Accessory for USBHub3c
Used for connecting a serial RS-232 interface to the control the USBHub3c through the expansion interface connector. Screw terminals are provided for the RS-232 interface. While this board provides for wiring connections, a host machine external to the USBHub3c is required for this control interface.
-
product
16-Channel RTD Signal Conditioning Card
ProDAQ 5821
The ProDAQ 5821 series of Signal Conditioning Cards is designed to interface with a variety of sensors, principally RTDs, Thermistors, Cryogenic Diodes and Voltage type sensors. Each version of the 5821 provides the capability of precise 4-wire measurement. In order to achieve this, a precise 500μA constant current source is provided per channel. The current source can be disabled on a per channel basis and is monitored to ensure that current is flowing. The value of the output current is stored...show more -
product
Packaged Direction Finding Systems
Doppler Systems offers packaged systems allowing for easy installation and use our radio direction finding systems. The packaged systems include a direction finding processor, an FM receiver, power distribution, a data interface to configure the system and obtain data from the system, and an appropriate antenna or antennas. Additionally, some customers require wireless networking to connect fixed and/or mobile sites together to share data. We also can provide laptop computers with our systems fully configured to interface with the direction finder and run our software.
-
product
Programmable DC Electronic Load
DL3000
The DL3000 series is a cost-effective, economical programmable DC electronic load with a friendly human-machine interface and excellent performance specifications. It provides a variety of remote communication interfaces to meet diverse testing needs for design and testing. A wide range of solutions are available for a wide range of industries including automotive electronics and fuel cells.
-
product
Programmable Electronic Loads
SFL Series
The SFL DC Electronic Load Series is a multi-functional programmable DC Electronic Load series that offers power levels of 300W (3U Half-Rack) and 1kW (3U Full-Rack) with high-speed current control (no dynamic overshoot/oscillation), high slew-rate (up to 30A/us) and stable operation at low voltage with no turn-On delay. It is lightweight and has a user-friendly front panel with built-in (USB) and optional (IEEE) communication Interfaces.
-
product
USB 3.1 Interface Module
Super speed “USB 3.1 type C modules” for RF Test Enclosures eliminate conducted and radiated interference while keeping data and power signals for USB 3.1 link untouched.
-
product
SonarMite Windows Tablet, Win 7, 8,10 & Mobile Software
The SonarMite software presents the user with a three window interface separated by ‘Splitter Window Bars’ which can be dragged to increase or decrease the active window size. If the window is sized to less than a proportion of its width then the window will suppress graphic output and present a scaled text message.
-
product
RF Prototyping Kit
VXI-5501
* VXI-5501 has a Bare Copper-clad Prototyping Board for RF and microwave modules.* Includes a VXI-5524 Register Based Interface Board with 48 digital IO lines and a 16-bit VXI data bus.* User configurable model number, manufacturer ID, version and serial numbers identifies the module as from your company.* Includes a blank front panel, side shields, manual, layout aids and VXI-Kit hardware for a single slot wide C-size module.
-
product
BOSS Simulator
Softdel’s BOSS Simulator is a sophisticated BACnet monitoring, debugging and simulation program that runs on any Windows® computer. It has a simple interface that is easy to use for BACnet professionals as well as novices. BOSS Simulator extends the functionality of Softdel’s BOSS Explorer by adding complex simulation and troubleshooting features, including support for A-side and B-side services, device discovery across routers and auto command generation across the entire network.
-
product
Fanout Buffers
Fanout Buffers are able to create multiple copies of input signal at their output and distribute them amaong several loads while achieving fast rise/fall time and low jitter. Input and output interfaces are CML and output voltage swing can be adjusted externally.
-
product
50 Ohm BNC to SMA Adaptor Assembly
40-978-511-1m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
MEMS Accelerometer
SQ-XLD
The acceleration sensor module performs calibrated acceleration measurement with digital serial output. Using a USB or RS232 interface cable (sold separately), it functions as a self contained data acquisition system for 2 axis or 3 axis acceleration, tilt, and vibration measurement.
-
product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Dual Channel
40-204-002
The 40-204-002 (PXI) and 42-204-002 (PXIe) are dual channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault. Using the fault bus, switches can simulate a short between both wires or a short to one of two externally applied fault conditions – such as battery supply or ground - via two fault buses.
-
product
Metro Expert
MX Series
The VeEX® MX product series offer a complete test solution for Metro Ethernet network installation and maintenance. Powerful features such as symmetrical and asymmetrical RFC2544 conformance testing, Multiple independent stream generation, Stacked VLAN (Q-in-Q) and MPLS tagging, and Dual Port Traffic Generation/ Analysis are available at 10GBase-R, 1000Base-X and 10/100/1000Base-T test interfaces. Fiber Channel testing at 1Gbps and 2Gbps rates is supported on select models.
-
-
product
Bus Interface
IP-1553
MIL-STD-1553 is a versatile standardized bus interface. MIL-STD-1553 is robust featuring Manchester encoding and enough voltage swing to provide excellent noise immunity and reasonable throughput rates.
-
product
DCA Equivalent-time Sampling Oscilloscopes
Equivalent-time (sampling) oscilloscopes are also known as digital communication analyzers (DCA). They are designed to visualize and analyze the analog properties of high-speed signals used in data center and wireline telecom applications. The Keysight DCA platform features a wide variety of optical, electrical, and TDR/TDT modules, compliance applications, and a common FlexDCA user interface to ensure more efficient testing in both R&D and manufacturing. Due to an ultra-low jitter and low-noise acquisition system, the Keysight DCA series provides industry-leading measurement accuracy for high-speed digital designs including 400G/800G Ethernet and Fibre Channel.
-
product
Avenir VIP IFE & CMS Systems
The new Avenir Line is the next generation of Cabin Management and In-Flight Entertainment Systems (CMS/IFE) from Astronics. Avenir incorporates the latest technologies to deliver native 4K video distribution through the highest bandwidth Ethernet network system in the industry. It also provides a fully customizable experience, which extends to the graphical user interface.
-
product
PXIe Remote Control Interface Module with Daisy-Chain Facility
43-921-001
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signalling.
-
product
3D Video Microscope
BVM-20102B
High-resolution CCD sensor, built-in analog/digital converter, analog and digital signal directly display on the screen, can also simultaneously display on TV and computer through corresponding interfaces; taking photo and video through software; easy operation, reducing user's fatigue and injury.
-
product
Air Data Calibrator
ADC-2550
TestVonics ADC-2550 Air Data Calibrator is a high accuracy pitot static calibrator. The ADC-2550 is capable of controlling and measuring Altitude and Airspeed pressures with the highest degree of accuracy. The control and measurement range of the test system can meets or exceed requirements for both commercial and military applications - the ADC-2550 is Nationally Stock Listed. The ADC-2550 is a derivative of the ADC-2500 Series. It features a touchscreen interface, a mid range 23PSIA sensor. It is ideally suited for Automated Test Equipment (ATE) applications.
-
product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Cut Ends, 2 Amp, 2m, 250 Port
A500RMR-C-4B200
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
product
JTAG Emulator
Blackhawk XDS560v2
The Blackhawk XDS560v2 STM emulator has System Trace capability, along with USB powered and LAN interfaces.
-
product
LiDAR Remote Sensing Payload Instrument
RESEPI™
Engineered for partners and resellers in the remote sensing industry, the Remote Sensing Payload Instrument, or RESEPI™, is a combined Dual Antenna GNSS-Aided Inertial Navigation System, datalogger, LiDAR, camera, and communications system that allows for the real-time and post-processed generation of point cloud solutions. The processing platform contains a WiFi interface, an embedded cellular modem to support RTCM corrections, data logging software, and gigabit ethernet. RESEPI™ can be used with commercially available LiDARs like Velodyne, Quanergy, Ouster, RIEGL, LIVOX, and Hesai. The device was built with the purpose of white labeling.
-
product
Special / Customer Spec. Crates
6U VME64x 6023 SNS Crates
The Spallation Neutron Source (SNS) in Oak Ridge (USA) is using WIENER VME64x crates of the 6023 style with front to rear cooling similar to the JLAB-style however, with simplified fan trays without display and interfaces.
