Showing results: 3331 - 3345 of 4171 items found.
-
Premier Electrosystems
Premier Electrosystems' Test Finger meets the standard requirements of IS guidelines. The Test Finger are wide range of probes used to meet the most common standards including those from BIS, IEC, EN, and others. Such standards require the checking of accessibility to exposed parts of home electronics and appliances, toys, tools, and a host of other products that are intended to be protected by enclosures. These probes simulate human fingers, tools, and other items that would be hazardous to come in contact with.
-
STT-ESD-2005 -
Beijing KeHuan Century EMC Technology Co,.LTD
Is a tester that meets the requirements of IEC61000-4-2 and GB/T17626.2. Its maximum electrostatic discharge voltage can reach 30kV, covering the electrostatic voltage requirements in the standard (the electrostatic voltage requirement for the fourth level of air gap discharge is 15kV), and it is suitable for more application fields and the requirements of future new standards. Therefore, the ESD-2005 electrostatic discharge generator can be used for most electrical and electronic equipment electrostatic discharge tests, and can ensure the comparability and reproducibility of the test.
-
Wuhan Sunma Technology Co., Ltd.
Passive Optical Components are the foundation stone of WDM Passive Optical Network (PON). Besides MUX/DEMUX and splitters, SunmaFiber also provides other passive optical components such as attenuators, circulators, collimators, and isolators etc. In addition, we offer Customized Service that products with various parameters can be designed to meet different requirements. With very high performance but lowest prices on the market, our passive optical components can be the most cost-effective solution for modern PON systems.
-
T1000-37 -
Tesuto Systems
T1000-37 breakout box is our most versatile model, using dual 37 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 74 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity. Ideal for continuity measurements, isolation testing, and signal capture.
-
pimd -
Ace Wavetech
The IMD (Inter Modulation Distortion) created in the passive components such as Antenna, Filters, Couplers, Dividers,Connectors and Cables become a harassing matter in the mobile communication network operators and maintenance engineers. Using AWT's various PIMD analyzer models, the manufacturers, designers and operators can reduce their time and cost to isolate those components before install the network systems. AWT has introduced the smallest and the most competitive PIM Analyzers with the lowest price in the globe.
-
CIRCOFLUX Product Family -
Foerster Instruments, Incorporated
The CIRCOFLUX test system is used for the non-destructive surface testing of ferromagnetic steel bars using the magnetic flux leakage method in accordance with standard EN 10221. This method is the most sensitive surface testing method for longitudinal, crack-like defects in hot-rolled ferromagnetic steel bars. The CIRCOFLUX sensor system therefore replaces subjective testing methods such as the magnetic powder test (magnetic crack detection) and visual checks, which are difficult to document and reproduce.
-
SEP/SIP -
Nihon Denji Sokki Co., Ltd
There are analog phase control type DC power supply type and digital control type inverter energy saving type. We provide the most suitable equipment according to the current capacity and cycle time.If the "start command" is executed from the existing molding equipment, each mode of "alignment-pause-demagnetization" is continuously operated by the program inside the instrument. It is also possible to share an emergency stop signal and output an output current abnormality signal.
-
IT-25B -
Clinton Instrument Company
While most military standards now favor high frequency spark testing over impulse spark testing, the IT-25B Impulse Spark Tester is available for use in some aeronautic applications that still specify the impulse method. The IT-25B meets the test requirements of military specifications MIL-C-13777E, MIL-W-16878, and NEMA standards for hook-up wire used in high temperature wire applications. This method is favored as an alternate to a wet dielectric test.
-
Conrad Braam
This protocol simulator started one weekend as a test program while developing a SCADA/HMI with modbus RTU and TCP/IP and afterward came in useful testing an embedded gnu-Linux device too. It has worked so well for me, I decided to put a nice GUI onto it and release it for free. The modbus protocol, also called open-mbus is implemented in many process control and monitoring devices, while most SCADA or HMI systems have a driver.
-
AQUADX Upgrade Kit -
CDx, Inc.
The AquaDx hand held water quality tester is for anyone who has ever been concerned about the quality of their well water or drinking water, and wants to get their water tested. AquaDx will test for a broader range of chemicals in water than most water testing kits and works with water testing labs and technology developers to make sure you have access to water testing services to check for the safety of your drinking water.
-
SiteX CP160D -
Teledyne ICM
The CP160D is the lightest and most compact generator of the CPSERIES. Featuring a built-in Beryllium window, it is the perfect generator for the inspection of light alloys such as aluminum, magnesium or fiber based materials like glass and carbon, as well as the greater thickness of steel. In fact, with its penetration capacity that is capable of reaching up to 37 mm of steel, the CP160D is able to execute many different types of NDT tasks without the need to ever have to add extra accessories.
-
mks Ophir
Ophir laser power meters work on the smart plug principle. This means that almost any Ophir power meter can work – plug and play – with almost any of the wide range of Ophir sensors. Ophir power meters are also the most precisely calibrated units on the market thus measuring with the highest accuracy. Noted for their versatility, ease of use, and user friendly interface, Ophir meters can be used stand-alone or interfaced with LabVIEW or the user's own software.
-
SA1002 -
Laplace Instruments Ltd.
The SA1002 provides a high performance capability to measure the EMC compliance of your products. It covers the conducted emission and radiated emission bands to 1GHz, as required by most EMC standards. The included software is Windows compatible and simple to use. This powerful system automatically sets the analyser parameters to suit the test to be performed. Standard limits are available from simple pull-down menu. Results can be directly compared against these limits for easy checks on compliance status.
-
Mors Smitt Group
Operating records for overhead power lines reveal that most faults are of a transient nature (e.g. lightning induced) & that service interruptions may be minimized by use of automatic reclosing of circuit breakers. An automatic reclosure of the circuit breaker, after the fault clears, provides improved service continuity & system stability. The 1B230 Series Reclose Relay provides for single or double shot automatic reclosing of circuit breakers, following interruption of supply due to a fault in the system.
-
AltaAPI -
Alta Data Technologies LLC
Alta’s 1553 and ARINC cards include the most advanced Application Programming Interface (API) library tools in the avionics industry, AltaAPI. The API architecture is a properly OSI modeled development package that provides an extremely flexible design to provide quick porting to various operating systems (such as VxWorks 5.X/6.X/7/MILS, Integrity, LynxOS RTOS), Linux 32- and 64-bit, Solaris 10, LabVIEW and 32- and 64-bit Windows 7/8/8.1/10.
