MOST
Media Oriented Systems Transport
-
Product
PXI 4-Slot BRIC Matrix, 2A 1-Pole 58x6, 1 Sub-card
40-596A-001
Matrix Switch Module
The 40-596A-001 is a PXI 1-pole 58x6 matrix in BRIC4 format and is part of a range of high density matrix modules able to switch up to 2 A or 300VDC/250VAC. The 40-596A BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
96-Pin 1.27mm Pitch Female Solder Pad Connector With Backshell, Screwlocks
C096SFR-4SP-5A
-
This connector is designed to allow users to discrete wires using solder pad connections to the 96-Pin 1.27mm pitch connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Intelligent Battery Charger-Analyzer for Large Battery Systems
SuperMasterCharger
-
The SuperMasterCharger is an instrument designed to charge, trickle charge and analyze ( discharge ) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries. With its multiple modes of operation: Constant Current Charge ( dual and single rate ), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge ( analysis ), Resistance Discharge ( analysis ) and Full Discharge ( deep cycle ). The SuperMasterCharger can satisfy the requirements of most large ( 10 A-hr to 100 A-hr ) rechargeable battery systems. The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit ( no load ) and Over-voltage conditions. Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights display the status of the operation.
-
Product
PXI 8 Slot BRIC 58x6 2A 1-Pole Matrix
40-596-101
Matrix Switch Module
The 40-596 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 150VDC/100VAC. The 40-596 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
Antennas
-
Elbit Systems of America’s antenna product line offers ruggedized, field-proven, military communication solutions for air, sea and ground operations. These advanced antennas deliver high performing, continuously connected voice, video, and data communications. Our technologies support high up/down-link rates and make our antennas ideal for fixed and maneuver units. Each system is designed to be fully integrated with most broadband satellite communication systems.
-
Product
Vibration Analyzers & Data Collectors
-
Wireless Vibration Analyzers and Data Collectors are replacing analyzers all over the world. Their easy connectivity and fast data collection timings make them the most convenient solution for vibration analysis nowadays. Digivibe products are the Vibration Analyzers with the largest number of functions in the market. They integrate advanced functions for Vibration Analysis and Dynamic Balancing with new Triaxial Wireless technology making them more portable and versatile. Furthermore, their compatibility with current mobile devices make them very easy to use and ultra-portable. ¡Meet our improved functions for bearing and gearbox analysis!
-
Product
High Temperature Un-Cooled Extensometers (700 C)
Model 7642
-
Jinan Testing Equipment IE Corporation
These extensometers use a high-temperature capacitive sensor and do not require any cooling. They will operate up to the maximum temperature limit of most environmental chambers used in materials testing. The Model 7642 is ideal for testing composites, metals and high temperature polymers in tensile, compression or cyclic testing. All units can be displaced in both compression and tension. The extensometer is supplied with the advanced DT6229 controller. The standard output is 0-10VDC analog signal, factory calibrated with the extensometer. This system provides a number of functional enhancements, including high speed digital output, built in calibration and tare functions, analog and digital filters, and more.
-
Product
SparkFun Altitude/Pressure Sensor Breakout
MPL3115A2
-
Life has its ups and downs, so why not measure them? The MPL3115A2 is a MEMS pressure sensor that provides Altitude data to within 30cm (with oversampling enabled). The sensor outputs are digitized by a high resolution 24-bit ADC and transmitted over I2C, meaning it's easy to interface with most controllers. Pressure output can be resolved with output in fractions of a Pascal, and Altitude can be resolved in fractions of a meter. The device also provides 12-bit temperature measurements in degrees Celsius.
-
Product
Non-Contact Sensors
IRIX
-
Sciences et Techniques Industrielles de la Lumière
IRIX™ is a family of non-contact sensors based on chromatic confocal technology capable of measuring distances and thicknesses on any material transparent to white light.IRIX™ is capable to measure simultaneously up to five layers of material. The controller can be used in combination with a large family of optical probes with different measurement ranges, mechanical dimensions and metrological specifications to best meet the most diverse application needs.
-
Product
Space-Qualified Products
-
Teledyne RF & Microwave has a rich history with more than 40 years of space heritage without any in-flight failures. We serve the commercial, scientific, military, and government communities with best-of-breed space solutions. As one of the first companies receiving MIL-PRF-38534 Class K certification, Teledyne earned the space community's trust by commercializing and supporting the industry's most comprehensive line of space-qualified products, from components to solid-state power amplifiers to integrated microwave assemblies.
-
Product
Multi-channel Battery Simulator
FT8340
-
Shenzhen FaithTech Technology Co., Ltd.
The FT8340 series is a high precision, multi-channel, dual quadrant programmable battery simulator.The current of the simulator can be charged and discharged，and supports various fault simulations, which can not only meet the requirements of BMS testing, but also meet the ATE testing of consumer electronics products.There are at most 12 channels in a device, and each channel is electrically isolated, which is convenient for users to use in series. The built-in upper computer software is easy to operate, flexible and easy to use. It supports single channel programming operations, multi-channel editing operations, and multi process programming operations.
-
Product
Gauge Type T Thermocouple Wire
W-TW-44
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Integrated Assemblies Products
-
Teledyne Microwave Solutions offers State of the Art integrated microwave assemblies (IMAs), utilizing custom building blocks and mixed media construction techniques to meet the most challenging performance and size constraints on the market today.
-
Product
Simultaneous Wavelength Dispersive X-ray Fluorescence Spectrometer
Simultix 15
-
Multi-channel simultaneous wavelength dispersive X-ray fluorescence (WDXRF) spectrometer system, the Simultix 15 high-throughput WDXRF spectrometer. Analyze beryllium (Be) through uranium (U) in almost any sample matrix. The most important metrics for automated process control are precision, accuracy and sample throughput. With up to 30 (and optionally 40) discrete and optimized elemental channels and 4 kW (or optionally 3 kW) of X-ray tube power, Simultix 15 delivers unparalleled analytical speed and sensitivity.
-
Product
PXI 4 Slot BRIC 132x8 2A 1-Pole Matrix
40-567-003
Matrix Switch Module
The 40-567 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 100VDC/70VAC. The 40-567 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
VME Power Supply
-
VME is a high speed and high performance bus system with powerful interrupt management and multiprocessor capability. It was created by combining VERSA-bus electrical specifications (1979) with the Euro card format resulting in the VME-bus Revision A - 1981 specification. The VME-bus specification has since then been refined through revisions B (1982), C, C.1, IEC 821 & IEC297 and IEEE 1014-1987. VME represents one of today's most used industry bus .
-
Product
EZ-Glider Position Control Telescoping Torque Arms
-
The position control telescoping torque arms help manufacturers detect and eliminate costly screw-fastening errors during the assembly process. Position Control telescoping torque arms are designed to reduce the risk of improperly fastened screws, ensuring that every screw is in the correctly tightened in the correct sequence. Using the EZ-Glider Position Control torque arm is like putting the eyes and ears of a quality control manager where they are needed most - right on the assembly area.The EZ-Glider Position Control telescoping torque arm consists of a torque reaction arm with encoders mounted at the base and a control box. The control box is used for programming and it tracks the axis movement by converting angle counts to the precise position of the screwdriver. The location is calculated from encoder values, allowing the operator to easily teach the torque arm a programmed sequence pattern and then use it to control the assembly process
-
Product
Light / Lux Meter, 40000 lx, 0.1 lx, 157 mm, 54 mm, 34 mm
72-9195
-
Handheld light meter provides a live reading of luminance in most environments. Convenient size easily slips in your pocket or tool kit.
-
Product
Smart Electric Tester
SET-12
-
The SET-12 Tester is a portable device for measuring electrical parameters. Unique combination of the most needed measurements into one device allows for a quick diagnosis of faults.
-
Product
Process Control Actuators
CVA Range
-
The CVA range of linear and quarter-turn actuators provide an electrically powered process control operator suitable for most control valve types and sizes. The CVA sets a new standard for process control and valve actuation. Rotork has proven expertise in applying new technologies in the automation of valves to bring enhanced performance and innovative features. This philosophy has now been applied to a new range designed specifically for the exacting demands of process control, specfically continuous modulating control valve applications.
-
Product
Nanoindenters
-
Nanomechanical testers from KLA Instruments™ provide precise, reliable and repeatable measurements of hardness, Young’s modulus, and other mechanical properties to help you explore new materials, reduce product failures and accelerate your time-to-market. We offer nanoindentation tools that range from easy-to-use to a high performance nanoindenter to the industry’s highest performance and most versatile nano tensile tester.
-
Product
Gauge Type T Thermocouple Wire
W-TW-24
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Inductively Coupled Plasma Mass Spectrometry / ICP-MS Systems
-
Agilent ICP-MS systems utilize innovative technology to deliver excellent sensitivity, accuracy, ease of use and productivity. Our 7800 and 7900 quadrupole ICP-MS systems offer the highest matrix tolerance, widest dynamic range and most effective interference removal for trace elements across most typical applications. The 8900 Triple Quadrupole ICP-MS (ICP-QQQ) adds MS/MS operation, providing precise control of reaction cell processes to ensure the most consistent and accurate results, resolving interferences that are beyond the capability of quadrupole and sector-field high resolution ICP-MS.
-
Product
Controllers
-
All BK Mikro controllers utilize the latest technology for the most flexibility and programming options. The compact, din rail mounted control unit mounts easily in the electrical cabinet and provides a full line of advanced functions.
-
Product
PXI/PXIe MEMS Optical MUX, Single 2-Channel, Single-Mode
40-855A-212
Multiplexer Module
The 40/42-855A-212 is a PXI/PXIe 2-channel multiplexer with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
Continuous Emission Monitoring Systems
-
TML has more than 50 years' experience designing, manufacturing, and supporting continuous emission monitoring systems (CEMS). We have a team of experienced CEMS air quality experts that will thoroughly review your process and operating permit and recommend the most cost effective and reliable solution for monitoring the gases of interest. TML's continuous emission monitoring systems are based on rugged, reliable equipment manufactured to exact standards. The result is products and systems with some of the highest mean time between failure rates in the industry. Whether it's a standard or custom solution, we stand behind our products 110%, guarantee CEMS certification, at least 95% uptime, replacement parts, and 24 x 7 support. We offer a total CEMS solution including data acquisition software for recordkeeping and reporting, lower cost of ownership, superior product reliability and designed for simple and easy maintenance.
-
Product
PICMG 1.0 Full-Size SBC Backplanes
Backplane
PICMG 1.0 Full-Size SBC Backplanes product line offer you low MTTR (Mean Time to Repair) approaches. The SBC backplanes are the most flexible and expansible solutions for industrial and slot-hungry applications.
-
Product
Telemetry Receivers
2U R200A Series
-
Systems Engineering & Management Company
R200A Series Receivers are designed for fixed and mobile Telemetry Ground Stations, but particularly for mobile applications where space is at a premium. The R200A provides for many of the same configurations and options available with the larger R600A and R400 systems, using the same cards, modules and RCMS network software for optimum interoperability. In addition, the RT200 Tracking Receiver configurations are an extremely popular, low cost solution for antenna tracking installations. The R200A provides the same proven performance and reliability and user interface of the R600A and R400. Like the R600A and R400, a "non-PC" configuration is available for remote operation via Ethernet. The 2U R200A receiver has become one of SEMCO's most popular receivers in terms of small form factor and operational performance and reliability.
-
Product
Event Detectors
105/106 Series
-
The 105/106 Series Event Detectors are the most versatile Event Detectors in the product line. These Event Detectors monitor the electrical resistance of up to 128 simple continuity loops, each comprised of single or multiple specimens under test. Each test specimen is continuously monitored while a selectable DC sense current is passed through each channel test-loop; resistance changes exceeding the selected threshold are recorded as an event. Minimum Event Duration, Channel Current, and Threshold Voltage settings can all be independently configured. 105 and 106 Series instruments are electrically identical, with the difference simply that the 105 offers four, 32-channel board slots and the 106 offers only one. Thus the 128-105 is equivalent to four 32-106 Event Detectors.
-
Product
Dynamic Vapor Sorption Analyzer
IGAsorp-XT
-
The IGAsorp-XT is a fully automated water sorption analyzer designed for measurements at temperatures and humidities beyond those available with conventional DVS analyzers. High resolution sorption isotherms are recorded at humidity values from 0.2 %RH or lower, using the unique climate-XT control method. Combined with high temperature water sorption measurements to 300 °C, an integrated pre-heater and completely flexible method programming, the IGAsorp-XT is the world’s most advanced benchtop DVS analyzer.
