-
product
Load Module for SLSC
Bloomy's 8-Channel Load Module provides isolated current and voltage measurements for eight on-board 5W loads or for eight off-board 120W loads. With built-in switching for calibration and fault injection, the module provides unsurpassed capability for Mil/Aero applications. The module also provides switching and connections to allow switching between a real load (e.g., actuator, valve, etc.) and the simulated load.
-
product
250 Watt Electronic Load Module
N3303A
The Keysight N3303A is a 250 W (0-10A, 0-240V) electronic load module for use in either the N3300A or N3301A electronic load mainframe in system applications. The N3303A load module is fast and accurate, for programming in constant current, constant voltage, or constant resistance modes, or for making voltage, current or power measurements. The N3303A can also digitize waveforms.
-
product
PXI Hex SPDT RF Switch, 8GHz 50Ω SMA, Terminated
40-880A-003
The 40-880A-003 is a hex SPDT 50Ω RF switch with 8GHz bandwidth. The 40-880A range of SPDT switches have automatic termination of unused signals and are available as a dual switch in a 1 slot PXI module, a quad switch in a two slot PXI module or hex and octal switches in three slot PXI modules
-
product
PXI-5650, 1.3 GHz RF Signal Generator
779670-00
The PXI‑5650 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5650 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
RF Coaxial Load
RF Lambda’s coaxial loads are used to terminate RF signal chain to provide a good 50ohm match and dissipate any excess RF energy. They are available in a variety of power levels and offer low VSWR.
-
product
500 Watt Electronic Load Module
N3305A
The Keysight N3305A is a 500 W (0-60A, 0-150V) electronic load module for use in either the N3300A or N3301A electronic load mainframe in system applications. The N3305A load module is fast and accurate, for programming in constant current, constant voltage, or constant resistance modes, or for making voltage, current or power measurements. The N3305A can also digitize waveforms.
-
product
PXI Quad SPDT RF Switch 6GHz 50 SMA Terminated
40-880-002
A range of 50Ω SPDT RF switching with automatic termination of unused signals. Available as a dual switch in a 1 slot PXI module, a quad switch in a two slot PXI module or hex and octal switches in three slot PXI modules.
-
product
DC Electronic Load Module, 1U Height, 60 V, 20 A, 100W
N6791A
The Keysight N6791A is a 100W, 1U electronic load module for the N6700 series modular mainframe.
-
product
PXI-2596, 26.5 GHz, 50 Ω, Dual 6x1 (SP6T) PXI RF Multiplexer Switch Module
778572-96
26.5 GHz, 50 Ω, Dual 6x1 (SP6T) PXI RF Multiplexer Switch Module—The PXI‑2596 is an RF signal multiplexer switch with dual 6x1 multiplexer banks in the same module. It is ideal for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules. You can use the PXI‑2596 onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
Basic RF Spectrum Analyzers
Our low-cost RF spectrum analyzers deliver general-purpose functionality and great value with measurement frequencies from 9 kHz to 7 GHz or 1 MHz to 20 GHz. Get the RF spectrum analyzer accuracy you expect with a variety of options provided to you by Keysight.
-
product
RF Signal Generators
RF Signal Conditioning provides signal manipulation capabilities for high-frequency or broadband signals. You can use these products to augment the capabilities of connected instruments to improve attributes like accuracy and frequency range.
-
product
Load Boards
The Hartmann Load Boards were originally designed for in house use to test, setup and qualify standard chassis and custom systems. As demand for these products presented itself, Hartmann answered the call with a lineup of high quality load boards.
-
product
Loaded Spectrophotometer
DSCD-900
DSCD-900 is a highly performance spectrophotometer with test caliber upward. The instrument adopts the geometric conditions of D/8 lighting and observation of CIE recommendations, integration of the full band LED composite light source, double beam optical system, ETC every-time calibration technology, spectral reflectance standard deviation within 0.08, maximum of colorimetric values ΔE*ab is 0.03, to provide all the necessary color formula. It could be widely used for coating, printing, textile, meet plastic, food, medicine, automobile field to meet customers’ measurement requirement.
-
product
Electronic Loads
SLH AC/DC
AMETEK Programmable Power, Inc.
From the leader in programmable power products, Sorensen introduces the SL series electronic loads which offer the best value with the most flexible platform. A wide range of loads are available from 75-1800W with both DC and AC input in benchtop, modular and standalone form factors.
-
product
Electronic Loads
T3EL Series
The T3EL series is a family of single channel, 200 & 300 Watt Electronic Loads that are ideal for R&D, product validation and Q&A in a bench or automated environment for low to medium power applications starting from 60mA, such as electronic components, batteries, portable chargers and power products. Electronic Loads are typically used to provide a load to the outputs of a power supply, usually capable of dynamic loading, and are fully programmable. Electronic Loads help designers to test electronic power products and ensure quality, reliability, and performance.
-
product
Load Cells
Instron is the only testing system manufacturer that designs and builds its own load cells, ensuring exceptional accuracy, stiffness, and alignment across a wide measurement range. Produced at Instron’s High Wycombe, UK facility, each load cell is temperature-compensated and calibrated to international standards for outstanding repeatability. Backed by the largest commercial deadweight stack in the U.S., Instron’s calibration process delivers precision that often exceeds industry requirements—providing reliable, traceable performance for even the most demanding materials testing applications.
-
product
RF Sources
Textron Systems’ commercial RF Sources (RFS 340, SSI) provide an unmatched combination of frequency coverage, power range, signal fidelity and switching speed in either a two-slot VXI, 1U LXI®, or VME Synthetic Stimulus Instruments (SSI) format.
-
product
RF Isolators
150 Watt Isolators include 35W Removable Loads, and can mount on 19" x 5.25" panels.200-400 Watt Isolators include 60W Removable Loads, and can mount on 19" x 8.75" panels.
-
product
RF Hybrids
RF hybrids are used for combining multiple power line carrier (PLC) TX/RX units together onto one cable without causing interference between transmitters and receivers. They are also used for splitting PLC signals to go to two or three phases of a power line.
-
product
Load Modules
Load Modules are available with a selection of voltage and current ranges. Use for discharge testing batteries, power supplies or test gear.
-
product
Terminations & Loads
We have more than 40,000 rf & microwave coaxial terminations in stock we can ship today. We offer these Microwave & RF terminations: SMA Terminations, Type N terminations, 7/16 DIN terminations, 2.92mm terminations, 2.4mm terminations, TNC terminations, smp terminations, minismp terminations, 4.1/9.5 minidin terminations. 4.3/10 terminations, ssma terminations, ssmc terminations, and a few Reverse Polarity terminations. Power levels of 0.5-150 watts. RF / Microwave terminations are also known as dummy loads or 50 ohm dummy loads. Our 1.85mm terminations, are rated to 67ghz. We offer 1.0mm terminations good to 110Ghz.
-
product
Coaxial Loads
Loads are supplied standard with N connectors, which are recommended above 500 MHz.
-
product
RF Components
Our Components product line consists of standard RF components and unique designs for custom microwave applications. We provide rugged, reliable and quality solutions for low and high power attenuation, termination, coupler, and power-divider applications. In addition to our extensive line of standard products, Bird has a reputation for designing custom solutions for custom applications. Bird has done hundreds of special versions of RF components to meet the unique needs of our customers. Common requests for customization include: Special Connectors, Non-Standard Attenuation Values, Mismatch Loads, Exceptional Peak or Average Power Handling Capability, Extremely Low VSWR Requirements, Custom Test Requirements and many others!
-
product
RF Socket
With unparalleled technology, coaxial structure, and high-precision machining equipment, LEENO can provide RF test socket with high bandwidth, impedance matching and high frequency up to 40GHz.
-
product
RF Downconverters
Today’s high-band signal standards are using higher frequencies and wider bandwidths than ever before for applications such as next generation 5G wireless services, satellite communications, electronic warfare, and more.
-
product
Load Testing
Load Testing, Simplified. We sort out the infrastructure, so you can spend more time testing. Tool Agnostic - We support JMeter, Gatling, Capybara and Selenium. Unfettered Testing - No limits on how you test, run as many users for as many tests, for as long as you like. Third-party Integration - Send results to Slack, Hipchat, Flowdock, or your own services using our API.
-
product
DC Electronic Load
EE15120A
The EE15120A DC Electronic Load / Works @ 0.0 Volts Input & real time I/O control attach the electronic load block to a heat- sink and your up and running. used them with D to A's, A to D's, Pots, PLC's to control the current. These Electronic Loads can be used for both Discharge & Charging Batteries & Devices. The electronic load can act as a Current Regulator for charging
-
product
Load Termination
A process of ending a transmission line or cable to either dissipate energy as heat or prepare it for connection to a device.
-
product
Loading Rheostats (Resistive Load)
Supreme Instrument Laboratories
Loading Rheostat is a device specially designed to meet the requirements of Engineering Laboratories, Electrical Test Rooms and Industries. It is used for loading transformers, power generators, supply mains etc. neatly and efficiently. It can also be used advantageously for regulating current and adjusting voltage besides its application for calibrating meters and thus eliminating the need for graded rheostats.
-
product
Smart Load Manager
Nippen Electrical Instruments Co.
This is flush mounting micro controller based instrument with multilayer PCB having SMT components offering accuracy and reliability along with reduction in EMI and EMC interference. These are specially designed to simultaneously measure, display and communicate several electrical parameters. This meter is an Ideal data source for effective Energy management, SCADA, PLC, BMS etc to measure as many as 36 parameters on 23 display pages, which are true RMS. The readings are displayed on 3 line bright Red 7 segment LED, each row/ line having 4 14.2mm high LEDS.





























