FlexRay
Protocol with data rate of 10Mbit/sec on two channels resulting in a rate up to 20Mbit/sec.
See Also: CAN
-
product
PXI FlexRay Interface Module
PXI FlexRay Interface Modules provide two fully functional FlexRay interfaces, allowing an individual electronic control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface. PXI FlexRay Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
PXI FlexRay Digitizer
PXD7113
Digitize high resolution waveforms with the fully isolated PXD series Digitizers. Minimize interference and measure "in-circuit". Measurement errors are reduced by a high input impedance.
-
product
3U CompactPCI Serial Vector FlexRay CAN LIN Module Carrier
SFV-RAY
The SFV-RAY is a 3U CompactPCI Serial carrier card for the Vector VN7610 and similar Vector FlexRay/CAN-FD compact interfaces. On-board USB controller. Can be installed in any peripheral slot of a CPCI Serial backplane.
-
product
PCI-8517, 2-Port FlexRay Interface Device
780685-02
2-Port FlexRay Interface Device—The PCI‑8517 is designed for developing FlexRay applications. As part of the NI‑XNET platform, the PXI‑8517 works well in applications requiring real-time, high-speed manipulation of hundreds of FlexRay frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The PCI‑8517 contains two fully functional FlexRay interfaces, allowing an individual engine control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface.
-
product
FlexRay Communications Expansion Kit
OP-SB88
The FlexRay communication is anticipated as a next-generation high-speed in-vehicle network.The OP-SB88 is an expansion kit that allows monitoring of FlexRay communications on up to two channels in real time. The kit incorporates a monitor function that does not require complicated parameter settings, and a simulation function with which the OP-SB88 works as a FlexRay communications node to transmit and receive data, thus powerfully supporting the initial development. The filter function and high-capacity memory greatly shorten the analysis time of trouble.
-
product
Single Bus 36-Channel 2A PCI Fault Insertion Switch
50-190-201
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
Single Bus 75-Channel 2A PCI Fault Insertion Switch
50-190-001
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
Testing of Rear Axle Steering
*2 high-precision servo axes for linear load simulation*Communication via CAN / Flexray*Function and noise measurements (NVH)*Supply and discharge of the test specimens via WTs on double belt conveyors*Connection to the production control
-
product
Advanced Platforms
TTConnect 616
TTConnect 616 is an advanced connectivity platform that combines and manages all in-vehicle interfaces such as CAN-FD, Flexray, LIN and Ethernet. Its wealth of interfaces is complemented by advanced traffic management software and support for Time Sensitive Networking protocols, making TTConnect 616 the ideal solution for future-proof vehicle architectures where different types of traffic must converge and operate in a safe and reliable manner.
-
product
PXI Differential Fault Insertion Switch Modules
Pickering's PXI Differential Fault Insertion Switch Modules support multiple channels of two-wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to externally applied fault conditions. *Two module types are available: Two wire fault insertion module suitable for CAN Bus and FlexRay.*High bandwidth two wire fault insertion module suitable for Gigabit Ethernet, AFDX and BroadR-Reach.
-
product
100BASE-T1 SPY 12 PORT
Art.-Nr.: TE-1500
Capture the traffic of 100BASE-T1, CAN/CANFD, LIN and Flexray Buses using only one device. The 100BASE-T1 SPY 12 port is a highly specialized test and evaluation tool for seamless capture of multiple in-vehicle-network technologies. It provides common timestamping of all incoming messages and delivers the traffic via Standard Gigabit Ethernet.
-
product
PXI-8517, 2-Port PXI FlexRay Interface Module
780689-02
2-Port PXI FlexRay Interface Module—The PXI‑8517 is designed for developing FlexRay applications. As part of the NI‑XNET platform, the PXI‑8517 works well in applications requiring real-time, high-speed manipulation of hundreds of FlexRay frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The PXI‑8517 contains two fully functional FlexRay interfaces, allowing an individual ECU to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface.
-
product
Dual Bus 64-Channel 2A PCI Fault Insertion Switch
50-190-102
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 4 Channel
40-200-004
Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signaling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
product
PCI Fault Insertion Switch Range for Differential Serial Interfaces
50-200/201
Pickering Interfaces, a leading supplier of modular signal switching for electronic test and simulation, is expanding its range of PCI Fault Insertion switching with the introduction of two new modules (models 50-200 and 50-201) designed for use with differential serial interfaces. PCI Fault Insertion Switch Cards for Differential Serial InterfacesThe new modules include the Differential PCI Fault Insertion Switch (model 50-200) which is designed for lower data rate serial interfaces such as CAN and FlexRay, and the High Bandwidth Differential PCI Fault Insertion Switch (model 50-201) which is designed for higher data rate serial interfaces such as AFDX and 1000BaseT Ethernet. Each module allows the introduction of fault connections that include data paths open, data paths shorted together, and data paths shorted to externally applied faults such as power supplies and ground. The software driver defaults to a protective mode where conflicting faults are prevented to avoid accidentally shorting unintended paths, such as power to ground. A separate mode allows complete freedom in setting fault patterns.
-
product
Configurable Data Logger
Rebel CT FlexRay
The Influx Rebel CT FlexRay compact data logger is ideal for development applications that requires up to 7 vehicle CAN 2.0 networks, FlexRay and additional LIN data.
-
product
Vehicle Communication Buses
Vehicle Communication Buses provide native support for Controller Area Network (CAN), Local Interconnect Network (LIN), and FlexRay frames and signals. Use these products for hardware-in-the-loop simulation, bus monitoring, automation control, and more.
-
product
CAN/FlexRay/Differential Bus PCI Fault Insertion Switch - 8 Channel
50-200-008
This PCI Fault Insertion card is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This card supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses.
-
product
Automotive Protocol Decode/Trigger Software (CAN, CAN FD, CAN XL, LIN FlexRay, SENT) for Infiniium Oscilloscopes
D9010AUTP
- Set up your scope to show CAN, CAN FD, CAN XL, LIN, FlexRay, and SENT protocol decode in less than 30 seconds- Support CAN XL protocol trigger and decode of the SIC mode (or slow mode) signal in the arbitration phase as well as the FAST mode signal in the data phase- Get access to a rich set of integrated software-based protocol-level triggers- Save time and eliminate errors by viewing packets at the protocol level- Use time-correlated views to quickly troubleshoot serial protocol problems back to their timing or signal integrity root causeThis application (for Infiniium Oscilloscopes) includes a suite of configurable protocol-level trigger conditions specific to CAN, CAN FD, CAN XL, LIN, FlexRay, and SENT. When serial triggering is selected, the application enables software-based triggering. Application supports CAN-dbc symbolic debug.
-
product
PXI FlexRay Digitizer
PXD7113
The PXD7113 FlexRay Digitizer features a 100MS/s input with 16Bit resolution, input voltages up to ±10V and a bandwidth up to 10MHz. The PXD7113 FleyRay Digitizer has a 2MB memory which allows up to1 million samples. The device has a high common mode rejection ratio (CMRR).
-
product
The all-in-one data logger for the entire vehicle networking
PM-200
The PM-200 sets the bar considerably higher on the topic of safeguarding and troubleshooting vehicles. Bus systems such as CAN, CAN-FD, FlexRay™, LIN, MOST150 and Automotive Ethernet are logged at a data speed up of to 120 MB/s. SSD removable media allow for quick evaluation and distribution of the data. Various upgrade options enable configuration for any application. Flexibility, programmability and support from debugging protocols make it possible to meet the high demands of functionality and fleet tests as well as of test runs.
-
product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 8 Channel
40-200-008
This PXI Fault Insertion module is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This module supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses. Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signalling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
product
Dual Bus 36-Channel 2A PCI Fault Insertion Switch
50-190-202
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
Dual Bus 75-Channel 2A PCI Fault Insertion Switch
50-190-002
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
Universal Analysis Tool
CANalyzer
CANalyzer is the universal analysis tool for ECU networks and distributed systems. CANalyzer makes it easy to observe, analyze, and supplement data traffic in CAN, LIN, MOST, or FlexRay systems. With powerful functions and user-programmability, all needs are covered from simple network analysis to advanced troubleshooting of complex problems.
-
product
SHDE9F-DE9F-FX Flexray Cable, No Termination, 1M
198290-01
9-Pin, Female D-SUB to 9-Pin, Female D-SUB FlexRay Cable - The SHD9F-D9F FlexRay Cable connects FlexRay interfaces to devices, breakout boxes, other interfaces, and accessories. This cable meets FlexRay cabling specifications and is compatible with all NI-XNET FlexRay interfaces. It offers 82 dB/km attenuation with no termination. The cable’s impedance is 100 Ω, 148.94 Ω/km at 20 °C resistance, and 5.2 ns/m delay. The cable features four 26 AWG twisted pairs and dedicated pairs for FlexRay Bus A and Bus B.
-
product
Single Bus 64-Channel 2A PCI Fault Insertion Switch
50-190-101
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
CAN/FlexRay/Differential Bus PCI Fault Insertion Switch - 4 Channel
50-200-004
This PCI Fault Insertion card is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This card supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses.
-
product
FlexRay Interface Device
FlexRay Interface Devices provide two fully functional FlexRay interfaces, allowing an individual engine control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface. FlexRay Interface Devices work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
Multibus Development and Test Tool for ECUs and Networks
CANoe
The versatile software tool for development, testing and analysis of ECUs and entire networks. Bus systems: CAN, CAN FD, LIN, MOST, FlexRay, Ethernet, WLAN, Car2x ITS G5, AFDX, J1708, ARINC429 > Protocols: TCP/IP, SOME/IP, CANopen, J1939, ISO 11783, J1587, MCnet, GMLAN, K-Line, CANaerospace and ARINC 825. Others upon request.
