Static Locators
Measure static electricity charges.
-
Product
Location Devices
-
Flash Pinger is a small battery powered acoustic transmitter as well as an optical flashing recovery device. Multiple settings allow for selection of flashing, timing, and frequency options for use in a variety of different applications.
-
Product
Visual Fault Locator VFL X5007
-
Metal case, Rugged and durableLow battery indication, to avoid leakage and wrong judgmentESD protection design, Protect the LD effectivelyIntegrated case, to avoid the case intermediate brokenRe-changeable ceramic tube, to avoid returning to manufacturer for this small faultLong battery life, up to 60 hours＠1mW
-
Product
Split-box Pipe & Cable Locator
-
Weshine Electric Manufacturing Co., Ltd
Pipe Locator is specially designed to detect pipes, sondes, telecommunication lines buried utilities. This device may detect buried power cables, CATV cables, gas and water pipes, sewer lines, telephone cables, fiber optic cables with sheath, sondes, inspection camera transmitters. The Transmitter emits a signal.
-
Product
Cable Fault Locator
TX4000
-
Auto Fault Location Rugged Palm-Top design Weighs less than 350g (12oz) 11 Measurement Ranges up to 4000m 25, 50, 75 & 100ohm Selectable Cable Impedance User Variable Gain Control Built in Tone Generator for Pair Tracing and Identification Suitable for testing all Communication and Power Cables Environmental Protection IP54 CE Approved Soft bag & Test Leads
-
Product
Traveling Wave Fault Locator
XC-2100E
-
XC 2100E, a Fault Location System based on principle of travelling wave detection is the solution to above problem. It can detect not only permanent fault, but also transient fault within one tower span accuracy (with best accuracy of ±50 meters). It is a kind of Line Monitor for continuous monitoring of transmission lines and gets triggered whenever travelling waves are generated on line due to switching, lightening or fault.
-
Product
Static and dynamic analysis
MEMS
-
Static and dynamic analysis and visualization are critical parts of the test and development process for MEMS microstructures in order to characterize surface metrology and measure in and out of plane motions. The PS4L Adaptive Architecture is ideal for configuring a system to perform tests to very specialized requirements of the MEMS customer. MEMS customers often require vacuum probing, which is available in semiautomatic and fully automatic configurations.
-
Product
Static Control Devices
-
Panasonic Industrial Devices Sales Company of America
There are many production processes where electrostatic charges disturb smooth operation. To eliminate static, Ionizers are used.Whether the application is for the Semiconductor industry where the components are extremely sensitive and can even be damaged by high electric static charges or for the packaging industry, where plastic sleeves or foils tend to stick to each other, Panasonic has a solution to neutralize electrostatic charge.
-
Product
Java Testing, Static Analysis, Code Review
Jtest
-
Parasoft Jtest is a complete Java developer's quality suite for static code analysis, code review, automated unit and component testing, coverage analysis, and regression testing ? on the desktop under leading IDEs and in batch processes.
-
Product
Pitot Static Tester
ADSE 650
-
The ADSE 650 caters fully for all aircraft types and the different electrical power supplies.It can be used for testing high performance civil and military aircraft, fix and rotary wings. This Pitot Static Tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems.The large touch screen display, with on-screen help ,enables all checks to be carried out easily on the flight deck or in the cockpit, by a single operator.
-
Product
Inductive Tone and Probe Cable Locator Kit
72-8500
-
This tone & probe set is a basic necessity for anyone running data, voice or any other low voltage cable. It is also suitable for tracing alarm, coax or speaker cables which are already installed.
-
Product
Underground Locators
-
Eliminate unnecessary digging or demolition by showing you where energized and de-energized wires, cables and pipes are located before you dig.
-
Product
Pitot Static Tester
ADSE 550
-
The ADSE 550 pitot static tester, housed in a plastic carrying case, is a portable, self contained field tester designed to test aircraft pilot ans static systems for leaks as well as the operation and calibration of airspeed, altimeter, engine pressure ratio, manifold pressure indicators, and other vacuum or low pressure units. The tester consists of a hand-operated vacuum pump, a hand-operated pressure pump vacuum and pressure gauges, 5 control valves, an altimeter and an airspeed indicator. The package accessories include two 25-foot hoses.
-
Product
Cable Fault Locators
-
Every day, GAOTek cable fault locators are used by electricians and technicians to find faults and breaks in underground electrical and communications cables.
-
Product
12" XGA TFT LED LCD Thin-Client Terminal With Intel® Atom™ Processor For Hazardous Locations Introduction
TPC-125H
-
Industrial-grade 12" XGA TFT LCD with 50K lifetime and LED backlightIntel® Atom™ E3845 1.91 GHz quad-core processor with 4 GB DDR3L SDRAM
-
Product
PXI-6704, 16-Bit, 32-Channel, Static PXI Analog Output Module
777796-01
Analog Output Module
16-Bit, 32-Channel, Static PXI Analog Output Module—The PXI‑6704 is a static analog output device. You can use the PXI‑6704 to create software-timed voltage and current output applications. You can independently set the output voltage range on each channel. The PXI‑6704 also includes eight 5 V TTL/CMOS digital I/O lines.
-
Product
Fiber Optic Power Meters and Fault Locators
-
Fiber optic communication systems require the right tools to commission new links and to troubleshoot existing links. Fluke Networks has a wide range of Fiber Optic testing products to help certify that power losses are within standards and to troubleshoot broken and high loss links on single mode and multimode fiber. Fluke Network fiber optic tools are designed to be rugged and reliable, and to get the job done.
-
Product
Fault Locator
BIDOYNG
-
BIDOYNG fits into existing LV fuse positions using two LV fuses in parallel, creating a robust single-shot auto-recloser. The primary fuse carries the load current until a fault causes it to operate. Then, after a user programmed delay, the secondary fuse is switched in and the network re-energised without customer interruption.
-
Product
Rebar Locator
Profometer PM-630 AI
-
The Profometer PM-630 AI advanced cover meter is a sophisticated instrument extending the application range of the Profometer PM-600 with the Line and Area Scan Modes and an extensive choice of statistical views.
-
Product
Multi-Channel PD System Locator
PDiagnostic Series
-
Power Monitoring and Diagnostic Technology Ltd.
The PDiagnostic is a portable system that utilizes Ultra-High Frequency (UHF), Acoustic Emissions (AE), High-Frequency Current Transformer (HFCT), and Transient Earth Voltage (TEV) sensors to detect, analyze, and locate the PD signals in real time for a multitude of medium and high voltage electric power equipment.The multi-channel PDiagnostic system locates PD on power equipment down to a meter by utilizing Acoustic-Electromagnetic Combination Location Technique, Time Difference of Signals’ Arrival (TDOA), Partial Discharge Signals Separation (PDSS), and 3D Positioning Technology with PC software included.The system features advanced PD diagnostic capabilities, automatic PD type pattern recognition, and accurate PD location capabilities. The PDiagnostic is an ideal trouble-shooting tool for your PD programs. Severity is determined and maintenance suggestions are provided accordingly.
-
-
Product
Cable Fault Location System
Syscompact 2000 M Pro
-
Cable fault location system 2000 M pro. The portable BAUR Syscompact 2000 M pro cable fault location system is used for cable fault location and cable testing in low- and medium-voltage cables up to 65 km length.* Fully integrated proven cable fault pre-location methods* Surge mode for acoustic pin-pointing* Easily transportable* Ideal for locations that are difficult to access
-
Product
Cable Fault Locator With Time Domain (Intelligent Bridge)
GT00ZD00ZY
-
GAOTek Cable Fault Locator with Time Domain has a reflectometer to locate faults in metallic cables and Intelligent bridge for tesing the broken line
-
Product
Short Circuit Locator for Power Cables
A910
-
The A910 is a short circuit locator designed for fault location in power cables. The instrument measures the ratio of the resistances of the two sections of failed conductor using a four-wire "Kelvin" connection, thus eliminating errors associated with contact resistances of the test leads. With the A910 you can determine if the cable has more than a short and locate the first and the last fault. The instrument locates fault with an insulation resistance up to 5 Mohms in cables that have a total resistance greater than 5mohm (approximately 90 m of 300 sqmm cable) and less than 30 kohms. The distance to fault is measured as a percentage of the total length of cable and is displayed on a large LCD display.
-
Product
Ground Fault Locator
GFL-1000
-
The GFL-1000 ground fault locator is used to pinpoint faulty grounding where electrical cables have breakage and lost to the ground. The GFL-1000 is recommended by NERC PRC-005-2 to inspect for unintentional grounds for VLA, VRLA and NiCad batteries every four calendar months. Included software allows for data management analysis.
-
Product
Utility Locator with Survey-Grade GNSS
RTK-Pro
-
Using the RTK-Pro internal cellular module with 4G LTE capabilities, the operator has the ability to connect to NTRIP RTK (Real-Time Kinematic ) caster that provides RTCM 3 corrections. By utilizing these corrections, the operator can collect both utility location data along with the geographical location of the utility with survey-grade accuracy. The RTK-Pro was designed for use at all operator levels, utilizing user-friendly and intuitive locate screens. Operators simply confirm the utility data with the press of a button and align the electronic spirit level to store the data. All field data is sent to the cloud and retained in the receivers onboard storage for review and exporting to external mapping programs.
-
Product
Static Analyzer for C or C++ Code for Compliance with MISRA, CERT
RuleChecker
-
AbsInt Angewandte Informatik GmbH
RuleChecker is a static analyzer that automatically checks your C or C++ code for compliance with MISRA rules, CERT recommendations, and other coding guidelines.RuleChecker primarily targets safety-critical embedded applications, but can also be used to analyze any structured programs, handwritten or generated, with complex memory usages, dynamic memory allocation, and recursion.
-
Product
S-Beam Static Load Cells
2519 Series
-
The 2519-xxxN Series load cells are specifically designed for use with 3300 single column testing systems. Automatic transducer recognition and electrical calibration makes them easy to use. The load cells incorporate overload protection and can withstand loads up to 150% of their force capacity without damage and 300% without mechanical failure. The load cells allow the user to zero out the tare weight of a grip or fixture that weighs up to 40% of the force capacity, while still maintaining the full specified accuracy.
-
Product
Tool, Crimp, TriPaddle (10 amp), Thermocouple, Micro Power, Receiver and ITA , Locator Required
910101102
Crimp Tool
This crimp tool can be used to crimp 10 Amp TriPaddle contacts, Thermocouple contacts or Micro Power contacts. Locator required.
-
Product
Metal Cover Locator
CS880
-
The CS880 Metal Cover Locator is a metal detector that will locate lost or hidden metal objects. It is most commonly used for locating manhole covers through tarmac and grass.
-
Product
Static Generating & High Speed Systems
-
The forces of static electricity are beneficial for many applications i.e. Bonding film to package prior to heat sealing - edge and/or web pinning at chill cylinder - bonding of protective covering to metal or wood. Many applications using DC ion production of either positive (+) or negative (-) ions to accomplish a bonding process are available.
