GPS Simulators
-
Product
Type 2, PCMCIA Dual Redundant MIL-STD-1553 serial bus Simulator Analyzer Tester
PC401
-
MIL-STD-1553 A, B, & McAir MULTI PROTOCOLS Simulator/Analyzer/Tester type 2 PCMCIA BUS Interface Card - The PC401 can be used for Validation Testing, ProductionTesting, full bus simulation and monitoring, as a generalpurpose 1553 interface or a stand alone bus Analyzer. Forprecise message scheduling and measurements, the Majorand minor frame times are independent of messagesequences or retransmissions on errors and the start of allcommand messages are independent of message length,response time or length of response. Message timing iscalibrated and RT responses have low jitter.
-
-
Product
ARINC-708/453 2-Channel Test & Simulation Module for the Weather Radar Display Databus
M8K708
-
The M8K708 module is an ARINC-708 / 453 2-channel test and simulation module for the Weather Radar Display Databus. The M8K708 supports two ARINC-708 / 453 channels, each selectable as transmit or receive. Each channel implements an 64K×16 FIFO and supports polling and/or interrupt driven operation.The M8K708 comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application. In addition, Excalibur produces adapter cables that convert the carrier board I/O Molex™ connector to two twinax CJ70-49 connectors. The cable may be purchased at an additional cost.
-
Product
Mouth Simulator
BO1032
-
As consumers demand smaller devices that produce better sound and need better microphones, you need to test your microphones using more than a simple 1kHz tone. Sweep tests require a good mouth simulator that can produce a sweep with a known steady SPL.
-
Product
PXI Single 16 Channel Switch Simulator
40-485-221
-
Designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions.
-
Product
Field Simulation Software
QuickField™
-
QuickField™ is a very efficient Finite Element Analysis package for electromagnetic, thermal, and stress design simulation with coupled multi-field analysis.
-
Product
Configurable Simulation Of ECU Diagnostics.
TestCUBE2
-
Softing Automotive Electronics GmbH
The ECU simulation TestCUBE2 is the counterpart for all cases of application in which an ECU is not yet (e.g. preparation of workshop tests) or no longer (e.g. tester regression test) available. TestCUBE2 is a configurable hardware and software solution for simulating ECU diagnostics with real bus communication. With just one device, you can simulate several ECUs or even an entire vehicle at the same time.
-
Product
GPS Signal Splitter 16 Way, SMA Jack, 1 - 2 GHz, 50 Ohm Coaxial
GPS161
-
INSTOCK Wireless Components, Inc
Wideband Frequency (1000-2000 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)15 VDC & 75 mA Max on DC Block PortsTri Alloy SMA Female (Jack) Low PIM
-
Product
SIM33EAU GPS Module
28504
-
Whether your project needs positional accuracy, high-speed movement estimations, high altitude measurements, fast update rates, or just plain ease of use, the SIM33EAU GPS Module has you covered.
-
Product
ARINC 429 Test & Simulation Interface for VME
VME-429
-
Avionics Interface Technologies
4, 8, 16, 32, or 64 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full Error Injection & Detection - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application interface supporting C, C++, C#, and .net development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME - Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
Product
Environmental Shock Simulation Machine For Drop Testing
-
# Simulates environmental handling threats small handheld products must survive.# Gauges your product?s ability to survive handling environments.# Controls key test variables: product orientation at impact; nature of the impact surface.# Maintains orientation to just prior to impact then releases for unrestrained impact.# llows user changeable impact surfaces to better simulate the handing environment.# Includes 4 ch short transient shock instrumentation system.
-
Product
3 Way GPS / GNSS Signal Splitter Passive, 1-2 GHz, SMA, DC Block+200Ω Load 3 Ports
GPS312
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.3 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy SMA Female (Jack) 50 Ohm
-
Product
Battery Simulator
G5.BAS
-
The G5.BAS series is bidirectional regenerative. It was developed specifically for the simulation of energy storage devices and batteries and is suitable for use in laboratories and on test benches. The modular and finely graded G5.BAS series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3.
-
Product
1 Or 2 Stream MIL-STD-1553 PMC Test And Simulation Modules With Prog. Coupling,onboard Bus Network And Variable Output Amplitude
AMCX1553-xT
-
MIL-STD-1553 Test and Simulation modules for PMC with 1 or 2 Dual Redundant streams plus 8 Discrete I/O’s (on Rear-I/O).
-
Product
Battery Cell Simulator
BCS-LABCAR
-
The ETAS Battery Cell Simulator (BCS-LABCAR) is a Hardware-in-the-Loop system which specifically targets the signal-level test, validation, and calibration of battery management systems (BMSs). The BCS-LABCAR is a high-precision Battery Cell Simulator that emulates the behavior of individual battery cells and packs across a wide range of challenging operating conditions, e.g. cell balancing over-charging, deep discharging, or pulse operation. The system is highly modular and thus scalable to emulate battery packs from a single cell all the way up to 200 cells.
-
Product
MIL-STD-1553 A / B Test And Simulation VME Module
VME-1553
-
*Dual redundant*1, 2, 4 or 8 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*VISA based VXI Plug & Play driver*Optional twinax front end
-
Product
Wavefront Modeling And Simulation
-
The CAST-CRPA Simulation Systems provide a precise, coherent, and repeatable GNSS RF signal “wavefront”, that is a perfect solution for testing phased array, or “CRPA” antenna systems, in a laboratory environment. The system generates a complete set of RF signals for each antenna element, which are referenced to the phase center of the antenna manifold. In addition, the CAST system allows users to add interference and IMU signals that can also stimulate EGI’s and a wide range of modernized navigation devices.
-
Product
GPS / GNSS Antenna Signal Splitters
-
INSTOCK Wireless Components, Inc
INSTOCK Wireless GPS Signal Splitters are available in 2-way thru 48-way configurations spanning 1-2 GHz with unpeered performance in GPS (L1-L5), GNSS, Galileo, GLONASS, BeiDou, and IRNSS antenna splitting applications. The 200 ohm internal load on the DC-blocked port(s) prevents receivers from incorrectly sensing an antenna fault when there is no current draw. Type N, SMA, TNC, BNC, and QMA connector configurations INSTOCK.
-
Product
Dropout, Surge, Ripple Simulator and AC/DC Voltage Source
DSR 100 Series
-
DSR 100 Series systems provide complete, single-box solutions for immunity testing. They include a simple-to-use yet powerful standards waveform generator matched with an industry leading power supply technology and come with an extensive library of tests for many automotive and aviation standards.
-
Product
Mechanical Simulation in Matlab
-
There are variety of numerical possibilities in the MATLAB and Simulink simulation environment. For those simulation environments we offer you various toolboxes that allow you to perform simulations easily and efficiently. These toolboxes can be combined with all available ways of MATLAB and Simulink. Our toolboxes can provide you support in the following areas: Analysis of structural dynamic behavior, Vibration and noise abatement, Design of active systems, Model Reduction, Ansys-Matlab interface.
-
Product
PXI Automotive Switch Simulator Modules
-
Pickering's Switch Simulator Modules are designed for automotive test applications. These modules simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. They allow automotive I/O devices to be tested for correct operation under adverse conditions.
-
Product
Solar Simulation Systems
-
PET Solar Simulators consist of a Light Source with a built-in Lamp Power Supply. The Solar Simulator has an ellipsoidal reflector that surrounds the lamp and collects most of the lamp output. The radiation from the lamp is focused onto an optical integrator that helps produce a uniform diverging beam. The beam is diverted 90° by a mirror onto a collimating lens. Special filters are placed between the mirror and the collimating lens to shape the radiation spectra to match various air masses. The output is a uniform beam that closely matches the sun's radiation spectra for a given air mass. Various models offer different areas of illumination. Each model can be manufactured to simulate the sun's radiation for different air masses.
-
Product
Data Link Simulator II
-
The Data Link Simulator II simulates a communications link, inserting delays and introducing errors so users can deter-mine what effects these impairments will have on their systems. The Simulator II includes a 35 x 20 character color LCD display. Context-sensitive help screens make it easy to use, without training or reference to a manual.
-
Product
ELECTRIC BRAKE FORCE METER WITH DYNAMIC LOAD SIMULATION AND CIRCUIT TESTING
MDTT9107
-
*Tests truck-side brake controller output and all towing-lighting functions without a trailer*Displays real-time brake controller output gain and timing*Quickly troubleshoots electrical circuits and ground condition*For use with aftermarket and integrated brake controllers*Microprocessor controlled; simulates trailer brake loads*25' cable allows one-man, in-cab testing of brake controller and all truck-side tow circuits*Use to verify that the vehicle’s adaptive (speed/load sensitive) brake-controller output is functioning properly
-
Product
Load Cell Simulators / Testers
-
A load cell simulator is a handy tool during initial setup, particularly of a batching by weight scale. It replaces the load cell(s) in the system allowing the scale technician to simulate various weights that will trigger the outputs setpoints for activating valves, gates, and mixers. These products are a must for anyone involved in scale installations and repairs.
-
Product
SparkFun GPS Breakout
NEO-M9N, SMA (Qwiic)
-
The SparkFun NEO-M9N GPS Breakout is a high quality GPS board with equally impressive configuration options including SMA. The NEO-M9N module is a 92-channel u-blox M9 engine GNSS receiver, meaning it can receive signals from the GPS, GLONASS, Galileo, and BeiDou constellations with ~1.5 meter accuracy. This breakout supports concurrent reception of four GNSS. This maximizes position accuracy in challenging conditions increasing, precision and decreases lock time; and thanks to the onboard rechargeable battery, you'll have backup power enabling the GPS to get a hot lock within seconds! Additionally, this u-blox receiver supports I2C (u-blox calls this Display Data Channel) which makes it perfect for the Qwiic compatibility so we don't have to use up our precious UART ports. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
Product
IP / VoIP Analysis & Simulation
-
GL offers high density Ethernet/IP tester variant which includes mTOP™ 1U/2U rack mount enclosures within which PacketExpert™ portable USB units are stacked to provide high density GigE ports form factor solution for testing GigE switches, routers and network conditions.
-
Product
GPS, GLONASS, Galileo Micro Splitter 2 Way, SMA, 1176.45 - 1602.00 MHz, 50 Ohm, Passive
GPSL12
-
INSTOCK Wireless Components, Inc
GPSL12 is a two way, passive, GPS signal splitter ideal for splitting a GPS antenna signal between two receivers while providing a DC current path to power remotely located active GPS antennas from the receivers. Maximum voltage rating is 50 VDC; max current rating is 1000 mA. Furnished with SMA female connectors all ports. Being a "micro-sized" splitter, GPSL12 weighs only 21 grams and is suitable for applications requiring low-weight parts.
-
Product
GNSS Testing & Simulation
-
Safran Federal Systems is a leading provider of advanced GNSS Testing & Simulation systems and tools for NAVWAR environments.
-
Product
Test & Simulation Interface for PCI Express
PCIe-C1760
-
Avionics Interface Technologies
HS1760/MIL-STD-1760E Test & Simulation Interface for PCI Express
