Showing results: 856 - 870 of 1348 items found.
-
NEO TELE-TRONIX PVT. LTD
Contemporary Test Sets For Transformer Industries are developed to recognize the potentially disastrous current transformer errors. They prevent the primary current from overpowering insulation and short circuits. They are used for developing a testing and maintenance plan for addressing the errors before any failure to save money and time. With these powerful test sets, they are sure to perform saturation testing to test the knee point of a signal by comparing primary and secondary windings.
-
SPHEREA Test & Services
TEC® Series generic purpose test benches are used by most airlines, systems manufacturers and MROs (Maintenance, Repair and Overhaul) companies to guarantee the conformity of critical electronic equipment. Available on all continents, the ATEC® Series can be adapted to suit various needs owing to its modular nature and capacity to test almost all airliner LRUs. SPHEREA has the world’s largest testing library.
-
ETL-35K -
Kharkovenergopribor Ltd.
ETL-35K system has a multitude of applications in electrical equipment testing and maintenance: testing cable insulation with DC (rectified) voltage up to 60 kV, measuring small leakage current of surge arrestors, high-voltage testing with AC voltage up to 100 kV at industrial frequency, underground utilities tracing, cable fault pre-location and pinpointing, and measuring capacitance and tan delta of various electrical objects at industrial frequency.
-
Conformiq Inc
Conformiq offers a next generation solution for automatic software testing. Our products fit the needs of Agile software development by adapting quickly to new product requirements and eliminating the time required for laborious test execution script maintenance during short sprints. Instead of using test cases, Conformiq users have a model, which describes the System Under Test, or the product you want to test.
-
Power Test, Inc.
Our equipment tests automatic and automated-manual transmissions. On and off-highway transmission test stands, transmission and hydraulic component test stands and valve body test stands. AIDCO Test Systems offers the latest in modern, electric motor and hydrostatically-driven transmission test stands. All units may include an air-cooled eddy current absorber (standard on the 450E), resulting in minimal dyno test cell noise and reduced maintenance.
-
CZ20054 -
Aegis Pty. Ltd.
Australian and New Zealand standards mandate testing of fault loop impedance on circuits not protected by RCD's, both at installation and after maintenance. The CZ20054 Loop Impedance Tester conducts earth fault loop impedance and prospective short circuit current (PSC) tests. The Aegis Loop Impedance Tester takes the confusion out of loop/psc testing by providing an automatic wiring check upon connection and single button operation.
-
V-Cone -
McCrometer
The V-Cone Flow Meter is an advanced differential pressure instrument, which is ideal for use with liquid, steam or gas media in rugged conditions where accuracy, low maintenance and cost are important. With its DP built-in flow conditioning design, the V-Cone is especially useful in tight-fit and retrofit installations in which the long runs of straight pipe required by Orifice Plates, Venturi Tubes, and other technologies are either impractical or unavailable.
-
N8487S -
Keysight Technologies
The Keysight N8480S Series Balance Thermocouple Power Sensors are intended to be used as measurement standards for RF power. They are suitable for use in a microcalorimeter-based primary measurement standard and as a secondary or reference measurement standard. The new balance thermocouple power sensors offer a broad frequency range DC up to 18/50 GHz, high maximum input power of +20dBm, fast measurement speed/settling time as well as ease of maintenance.
-
N8481S -
Keysight Technologies
The Keysight N8480S Series Balance Thermocouple Power Sensors are intended to be used as measurement standards for RF power. They are suitable for use in a microcalorimeter-based primary measurement standard and as a secondary or reference measurement standard. The new balance thermocouple power sensors offer a broad frequency range DC up to 18/50 GHz, high maximum input power of +20dBm, fast measurement speed/settling time as well as ease of maintenance.
-
40-255 -
CTEK Power USA
The groundbreaking CT5 TIME TO GO (part #40-255) battery charger and maintainer is a world first because it answers the question ‘When will my battery be fully charged?’This means you can plan your day around your battery charging because the CT5 TIME TO GO gives you an accurate prediction of the remaining charging time in hours. Not only that, it’ll also tell you when you can safely try to start your vehicle before the battery is fully charged. The CT5 TIME TO GO uses advanced technology to give you three charging and maintenance programs – Normal, AGM and Recond. It’s easy to use and fully automatic, so it can be connected directly to the battery indefinitely, if required, and it won’t over or under charge. The CT5 also has built-in temperature sensing capabilities.
-
PCE Instruments
The handheld tachometer is a means of measuring revolutions within the industrial sector, either optically or mechanically. The handheld tachometer can be used for maintenance and calibration of machines that have moving parts. The principle is similar to a bicycle speedometer, where time will be measured until a wheel has completely turned. The handheld tachometer has two different measurement methods.The handheld tachometer may have a contact connection to the moving parts. Alternatively, the handheld tachometer works with reflecting marks. This will be secured on the moving part. As the laser strikes the reflecting mark during rotation, it will be reflected and detected in the handheld tachometer via a sensor. Rotation speed and speed can be seen on the handheld tachometer. The handheld tachometer may combine both possibilities (contact and non-contact connection). Next to the handheld tachometer you find other devices for measuring revolutions at PCE Instruments.
-
ASXPRESS Plus -
Teledyne LABS
A sample introduction system such as the ASXpress® Plus from Teledyne LABS reduces the time required for autosampler movement, sample uptake, stabilization, and rinse operations, thereby reducing sample run times significantly. The result: more sample throughput in less time. The accessory’s design allows multiple functions to occur simultaneously. A highspeed vacuum pump loads the sample and flushes the sample uptake path substantially faster than a conventional peristaltic pump.When coupled to a compatible autosampler, the ASXPRESS Plus Rapid Sample Introduction Accessory minimizes times for sample delivery, stabilization, and washout with ICP-AES or ICP-MS. The result is increased sample throughput by up to 5 times or more. In addition, the ASXPRESS PLUS reduces costs from argon, power, ICP-AES / ICP-MS components, and system maintenance.
-
EcoChyll X1 -
Teledyne LABS
You can think of the EcoChyll X1 as a chiller with no tank, no coolant liquid, and which achieves its setpoint temperature in just one minute. It has a built-in condenser, connects to any brand of benchtop rotary evaporator, and has a footprint under one square foot.Want more? The EcoChyll X1 involves less tubing and fewer opportunities for leaks.Still want more? The EcoChyll X1 uses about one quarter of the electricity of a recirculating chiller with a similar cooling capacity.The EcoChyll has virtually no maintenance or setup requirements. Connect it to your existing rotary evaporator, plug it in, turn it on, and it’s ready to go.Ecodyst has pioneered a smart self-cooling technology with no consumables as compared with traditional rotary evaporators. Upgrade your rotary evaporator with EcoChyll X1 and immediately begin to benefit from the many advantages it offers.
-
CBAnalyzer -
Circuit Breaker Analyzer Inc.
Simple operation requiring minimal trainingVery portable - it's a laptop or tablet pc running our Windows software programNo modification of the circuit breaker is requiredNo electrical connections are requiredRemoval of the circuit breaker from its mounting or cubicle is not requiredTesting can be performed during routine switchingData is easily transmitted over the internet to the users account where it is analyzed and compared with a known good profile (KGP) for that type of circuit breaker to determine: • Overall mechanical condition • Confirm maintenance intervals and lubrication • First trip testing data for arc flash compliance • Arc flash study validation checksPerform detailed analysis and store maintenance records using CBAnalyzer suite softwareAccess to the CBAnalyzer Account Manager which: • is where user accounts are created and each user's role is designated • provides access to your equipment database and test data archives • is where tests are synced • is where your equipment data is entered and stored • is required to use the CBAnalyzer software program
-
FLIR T865 -
Teledyne FLIR
The FLIR T865 thermal imaging camera is a non-contact inspection tool with 180° rotating optical block that allows users to safely and comfortably assess the condition of critical electrical and mechanical equipment in utility and manufacturing applications. With advanced features including unmatched temperature measurements down to -40°C, accuracy as good as 1°C/1%, 1-Touch Level/Span contrast enhancement, and laser–assisted autofocus, you'll get highly accurate temperature measurements every time. Pair the T865 with a 6 FOV IR lens to perform inspections on small targets from long distances. The on-board Inspection Route system helps you record temperature data and imagery in a logical sequence for faster troubleshooting and repair. The T865 also features FLIR Ignite for automatic uploading of images directly from the camera to the cloud for easy, secure storage and sharing. Adding a FLIR T865 camera to a condition monitoring/predictive maintenance program can help reduce maintenance costs, improve system efficiency and reliability, and prevent downtime due to outages.
