Solar Simulators
replicate the sun's light.
See Also: Solar Simulation, IEC 60904-9, I-V Tracers, Solar Reference Cells
-
Product
Lightning Surge Simulator
LSS-720B
-
Voltage surge test (1.2/50µs) and current surge test (8.2µs) specified under JEC-210 and 212 standard. (JEC: Japanese Electrotechnical Committe)High voltage surge test up to 20kV and high current surge test up to 4000A (30kV/6000A model available)
-
Product
Solar Analyzers
-
Max. solar system power (Pmax) search by Auto-scan: 1000V, 12A (12000W capability)The analyzer and the Remote Solar Detector is connected by Bluetooth wireless communication (Bluetooth 2.1 + EDR Class 1)The Remote Solar Detector is moisture-proofIntelligent test logic with no personnel attendance required in the field Solar system analyzer waits and tests the system until appropriate sunlight irradiance is detectedMax. voltage (Vpm) at Pmax, Max. current (Ipm) at Pmax Voltage at open circuit (Voc), Current at short circuit (Isc)Efficiency (%) calculation of solar systemTemperature measurement of solar panelsIrradiance measurement of sun lightSeries resistance (Rs) calculation of solar panelsWith data logging/open function, the I-V curves of solar system can be analysed / recorded for a period of time (e.g. 60 min.)Conversion of I-V curve under OPC to data under standard test condition (STC) based upon IEC standardProvide Operating Condition (OPC) and Standard Test Condition (STC) test reports for verification of solar panel performance (OK or NO OK)Users can set up the parameters of solar panelsUsers can set up the series number of solar panels. Parameters of many solar panels can be measured in one measurementThe Irradiances and Temperatures of solar panels can be continuously measured, monitored and recordedContinuously measure/monitor/record the DC power output of solar system and the AC power output of inverter (1 phase or balanced 3 phases)Calculate the efficiency of DC to AC power conversion and the efficiency of the max.output power
-
Product
Basic Rate and Primary Rate ISDN Network Simulator
Emutel Duo
-
Emutel Duo is a convenient and flexbile basic rate and primary rate ISDN network simulator. With 3 software selectable S/U interfaces and optional 2 E1/T1 interfaces you can test and develop a full range of ISDN equipment.
-
Product
Solar Module Tester
REOO GIV-20A2616
-
REOO GIV-20A2616 Solar Module Tester is designed for PV module manufacturing inspection, enabling fast module performance inspection and stable production quality verification. Built for solar factories, it supports reliable module testing decisions.
-
Product
SOLAR CELL TESTER
-
The tester is designed for terrestrial solar cell incoming/outcoming inspection with the purpose of checking and optimizing parameters and preventing manufacture defects of solar modules. Solar cells are not heated in process of inspection due to the use of xenon pulse lamp installed in the tester.
-
Product
Solar Cables And Connectors
-
All of our Solar Connectors are thoroughly tested and TUV 1500VDC and UL1000VDC approved. These connectors provide reliable, waterproof and anti-aging features, and are proven to withstand any heavy environmental conditions. Other Solar Connectors typically have a water permeability rating of 66 or 67. Our IP68 rating ensures that our Solar Connectors will hold up in the most severe environmental conditions including sand storms and water submersion up to 3 meters. Our solar connectors are compatible with any solar connectors in the industry. We have designed our connectors to complement other solar connectors as well as replace them. Whether you’re looking for solar connectors to use with your current ones or searching for solar connectors to start a project, our solar connectors will be right for you.
-
Product
Solar Cell I-V Characterization System
VS6825
-
Industrial Vision Technology Pte Ltd.
The VS-6825A I-V test system is tailored for high-efficiency Solar cell production lines. It is able to eliminate the impact of HJT/IBC/TOPCON’s high capacitance characteristics on measurement results.
-
Product
Hot Socket Simulator
Hot Socket Simulator
-
The new TESCO Hot Socket Simulator gives you the ability to investigate meter failure issues related to hot socket phenomenon. The Simulator is equipped with one 2S meter socket with four jaws, one of which is the heated jaw. The arcing/heating apparatus can be moved to any of the four jaws (jaw 1 is the standard). Additional arcing/heating elements can be provided as an option for multiple hot jaws on the existing socket.
-
Product
Calibration Cable, 78-pin D-type, Thermocouple Simulator Modules
40-975-078-1m
-
This cable assembly is specifically designed to connect to the 78-Pin D-Type port on the front panel of Pickering Interfaces Thermocouple Simulator Modules 41-760 and 41-761 enabling calibration via an external DMM.
-
Product
PCI Strain Gauge Simulator Card, 2-Channel, 1.5k
50-265-402
-
Designed to simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. It provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
Single Or Dual Stream MIL-STD-1553A/BTest And Simulation Module For Standard Ethernet
ANET1553-x
-
The ANET1553-x is a member of AIM’s new line of Ethernet based modules for analysing, simulating, monitoring and testing MIL-STD-1553A/B databuses. For wireless applications, an ANET compatible USB Wifi dongle is optionally available. The capability to execute Python scripts in the ANET is a standard feature. For applications with multiple ANET devices AIM offers the ADock ANET Docking Station to host up to 4 ANET modules.
-
Product
Multiphysics Computational Fluid Dynamics (CFD) Simulation & Analysis
STAR-CCM+
-
Siemens Digital Industries Software
STAR-CCM+ is a stand-alone simulation solution for computational fluid dynamics (CFD), computational solid mechanics (CSM), heat transfer, particle dynamics, reacting flow, electrochemistry, electromagnetics, acoustics and rheology. STAR-CCM+ delivers accurate and efficient simulation technologies through a single integrated user interface and automated workflows. This facilitates the analysis and exploration of complex real-world problems.
-
Product
Simulation Tools for Analog and Power Electronics
SIMetrix
-
Complete mixed-mode simulation package providing high performance, ease of use and superior analog convergence.
-
Product
PXI RTD Simulator Module, 12 Channel, PT1000
40-263-303
-
The 40-263-303 is a 12-channel PT1000 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
Handheld ESD Simulator
-
Battery operated handheld ElectroStatic Discharge (ESD) generator up to 30kV.Discharge networks according to IEC 61000-4-2, ISO 10605, MIL-STD-461 CS118, DO-160 section 25 and many more standards.
-
Product
2 PRI + 24 BRI-U ISDN Simulator
CH-24BRI-U-MOD-2PRI
-
The most inexpensive ISDN simulator on the market. This unit has two PRI ports and 24 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network.
-
Product
ARINC 429 Test & Simulation Interface for PCI
PCI-C429
-
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection - Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/FilteringIRIG-B time code encoder/decoder with free-wheeling modeApplication Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
EFT/Burst Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
High-end test instrument of EFT/Burst for new energy, which fully comply with CE and CCC certification. With a built-in three-phase five-wire automatic coupling /decoupling network EFTN 69100T, it can meet the requirements of new energy test system and high power load test. It is featured with good reliability, stable performance and easy use.
-
Product
Collins Radar Fixture with Gyro Simulator
TA-3A/B
-
This weather radar test fixture is a combination of the established WXT-250 series fixture and the RDR-2000 and RDR-2100 radars so that a single panel will provide many features that are still required today. The gyro simulator built into the panel is usable for either radar being tested and eliminate's plugging in any external simulator. The features for both product lines as shown in their respecting CMM's are provided on the panel so that full testing and alignment of these radars and their system components can be tested and/or evaluated. If you require any changes or other product versions please give us a call.
-
Product
IEC61000-4-11 Voltage Dips And Interruptions Simulator Generator
VDS-1120DX
-
Shenzhen Chuangxin Instruments Co., Ltd.
The voltage dip and interruptions generator is specially designed according to the characteristics and requirements of EMS measurement under a sudden reduction or interruption of the voltage at a point, CSS61000-11/ CSS61000-11T used a big LCD in both English and Chinese operating interface. They have more fine performance such as high reliability, convenient operation, and full meet the standard requirements of IEC 61000-4-11, EN 61000-4-11 and GB/T17626.11
-
Product
Bipolar DC Power Supply / Battery Simulator
IT6400 Series
-
The unique bipolar voltage/current output makes IT6400 series can be used as a bipolar power source or a bipolar electronic load. The battery simulating function is especially applicable for development and high speed production testing of portable, battery-operated products.
-
Product
Regenerative Grid Simulators 9kVA-15kVA
-
Chroma Systems Solutions, Inc.
Four quadrant, single- or three-phase AC power sources designed to simulate real-world grid characteristics for EV, PV inverter, and smart-grid test applications.
-
Product
Force On-Force Reactive Tactical Readiness IADS Simulation
FORTRIS™
-
FORTRIS™ is a scenario engine that provides a real-time complex battle simulation between hostile and friendly forces. The Synthetic Environment within FORTRIS contains a true multi-layered Integrated Air Defense System (IADS) simulation that can act and react both as an overall system, as well as individual contributors, making it the ideal cognitive training tool within the Live Virtual Constructive (LVC) world.
-
Product
MIMIC sFlow Simulator
-
MIMIC sFlow Simulator generates a variety of flows and enables you to fully test your applications. Since you have a complete control over generated flowsets you can easily verify that your graphing application is correctly displaying the values and your collector correctly collects precisely generated flowsets.
-
Product
Grid Simulator
PAS-F
-
The Intepro PAS-F Series is a broad line of programmable three phase output regenerative utility grid simulator products. With power levels ranging from 45kVA up to 1.6MVA, the series is capable of testing the largest of dispersed energy inverters. The PAS-F combines utility grid simulation with regenerative bi-directional AC source controlled power that is capable to both source and sink full current from the equipment under test (EUT).
-
Product
MIL-STD-1553 A / B Test And Simulation PCI Express Module
PCIe-C1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
Crash Simulation Systems
-
The crash simulators are capable of reproducing a wide range of standardized and user-defined crash tests including advanced applications such as side impact and vehicle pitch simulation. Instron’s acceleration sled systems are used for the development and approval of vehicle safety systems, vehicle parts and also for the investigation of solids and structures during crash events.
-
Product
Test And Simulation Devices
BreakingPoint
-
Control global threat intelligence at Internet-scale to create massive-scale, high fidelity simulation and testing conditions for battle-testing infrastructures, devices, applications, and people.
-
Product
NIBP Simulator
SC-3 SimCube®
-
This NIBP only simulator provides features to perform basic NIBP testing of a patient monitor. Features one-button operation for quick testing of patient monitors and optional Battery Boost Option. Optional accessories provide all you need to test the NIBP parameter on any type of patient monitor.
-
Product
8 Port Phone Line Simulator (FXS) Adv
CH-8FXS-A
-
This unit has 8 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, modems, access servers, audio conference equipment or anything that requires phone lines. Telephone line simulator acts like a "telephone company in a box" providing dial tone, ring voltage and all advanced phone line features such Caller ID, Call Waiting, Call Hold, Three Way Calling and many others.
