I²C
A slow Inter-Integrated Circuit bus protocol.
-
Product
1 GHz, 1 MΩ, 0.9 pF Active Probe
ZS1000
-
Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.9 pF) to reduce circuit Loading across the entire probe/oscilloscope bandwidth. The ZS1000 is ideal for 200–600 MHz oscilloscopes.
-
Product
Battery Tester
G5.BT
-
The G5.BT series is bidirectional regenerative. It was developed specifically for testing energy storage devices and is suitable for use in laboratories and on test benches. The modular and finely graded G5.BT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The G5.BT series has an outstanding current accuracy of <0.02% FS, an additional high-resolution current measurement range, and a fast current rise time in the 100 μs range. Ripple modulation, an integrated safety relay for PL c according to EN ISO 13849 and a powerful CAN multi-protocol interface (1 kHz, 16 bit) as well as functions to avoid reverse-polarity problems, current surges, and unwanted deep discharges make the G5.BT series the ideal, versatile battery module and battery pack tester.
-
Product
sbRIO-9862, Non-Enclosed, 1-Port, High-Speed, Flexible Data Rate C Series CAN Interface Module
785963-01
CAN Interface
Non-Enclosed, 1-Port, High-Speed, Flexible Data Rate C Series CAN Interface Module—The sbRIO‑9862 is a high-speed Controller Area Network (CAN) Flexible Data‑rate (FD) interface for developing applications with the NI‑XNET driver. The sbRIO‑9862 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The sbRIO‑9862 is only compatible with CompactRIO systems. Non-enclosed modules are designed for OEM applications.
-
Product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Cut Ends, 0.5m, HV
A037DM5-C-HA050
Cable Assembly
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
AFDX ® / ARINC 664 Test And Simulation PCI Module
PC104p-429
-
*4 or 8 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*128 MB RAM*Label selective triggering for recording / filtering*Real-time recording and later analysis of multiple channels*Sorting according to SDI field*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
Ethernet to GPIB Controller
Model 9065
-
* Controls GPIB Devices anywhere there is a network or internet connection.* No special driver required which eliminates driver problems. * Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls.* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* Fully VXI-11 compliant. * Includes ICS's VXI-11 and VISA keyboard control programs. Control instruments without a program. * Works with Agilent, NI and Kikisui VISA libraries.* Internal webserver lets you change network settings from any browser.* Network connectivity eliminates GPIB Bus Extension problems.* Allows multiple users to access the GPIB instruments.* Supports GPIB and HP-IB 488.2 complicant instruments.* 9065 is a 2nd generation drop-in replacement for ICS's Model 8065. The Model 9065 is 2x to 4x faster and includes a webserver instrument control page.
-
Product
SH37F-Tajimi Shielded Cable, 10M
199254-10
Multifunction Cable
37-Pin D-SUB Female to 4 7-Pin Tajimi Female, C Series Strain/Bridge Input Module Multifunction Cable - The SH37F-Tajimi connects with compatible sensors to accessories or cables with Tajimi push-pull connectors.
-
Product
EN 50155 M12 8FE Managed Switch
EKI-9508E-MW
-
M12 connector with IP67 rugged housing, Complies with EN50155 & EN50121-3-2, Complies with EN45545-2 & EN61373, Wide nominal power input range: 24~110VDC; Operating power input range: 16.8~137.5VDC. Compact size to fit in different narrow spaces, Operating temperature: -40 ~ 70°C.
-
Product
Alternate 2.82 (80.00) - 5.00 (141.00) General Purpose Probe
HPA-74T65-1
General Purpose Probe
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Test Center Remark: max. test center 187 mil / 4,74 mmFull Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 75Recommended Travel (mm): 1.91Mechanical Life (no of cyles): 2,000,000Overall Length (mil): 598Overall Length (mm): 15.19Overall Length Remark: Tip “A-B”: 598 (mil), 15.19 (mil), Tip “C”: 586 (mil), 14.88 (mil), Tip “E, T135, T156, T65, T80”: 610 (mil), 15.49 (mil), Tip “T75”: 620 (mil), 15.75 (mil)
-
Product
Stability Testing Chamber - Single Door Model
Q40
-
Canden stability testing chamber is capable of maintaining stable temperature set points of 25°c , 30°c & 40°c corresponding relative humidity set points of 60%RH(@25°c), 65%RH(@30°c) and 75% RH(@40°c) with exceptional precision. The chamber has a wide operating temperature range of 18°c t to 40°c maintaining a stable temperature across the entire range.
-
Product
Kelvin Test Contactor
cCompact
-
cCompact™ test contactor offers a reduced site-to-site pitch concept enables high parallel test for power applications on strip test and pick and place handler platforms.Featuring compact Kelvin footprint with outstanding CRES stability by Denmark pin material. Automotive temperature range -60°C to +175°C. Integrated Socket Air-distribution.
-
Product
Universal PMICs
-
PowerArchitect™ design and configuration software speeds development and significantly reduces overall time-to-market compared to legacy analog power solutions. An I²C interface and multiple GPIO pins ensure easy system integration. Configurable warning and fault levels, fault behavior and power up and down sequencing ensure any load can be properly powered and protected. The power system design can be completed with confidence long before the final revision of the SoC or ASIC is available.
-
Product
Chlorophyll Concentration
-
Linear OutputThe Apogee chlorophyll concentration meter is calibrated to measure chlorophyll concentration in leaves with units of mol of chlorophyll per m2. This eliminates the problems with relative indexes of chlorophyll concentration.For reference and comparison purposes, the Apogee meter also outputs relative units [CCI or SPAD] if desired.For details see: Parry, C., Blonquist Jr., J.M., & Bugbee, B. 2014. In situ measurement of leaf chlorophyll concentration: analysis of the optical/absolute relationship. Plant, Cell and Environment 37:2508-2502.
-
Product
Cable Assembly, 9-Pin D-Type Female to Unterminated With Tinned Ends, 1m, HV
A009DF4-T-HA100
Cable Assembly
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
Product
Temperature Logger
SRIL-8
-
The LogTag® Dry Ice “Probe-less” Temperature Logger operates, measures and stores up to 8000 temperature readings in temperature environments ranging from -80°C to +40°C (-112°F to +104°F).
-
Product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
785190-02
Voltage Output Module
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
Product
Needle Microprobe
MT-23/8HT
-
Fast-response 23 gauge needle probe, (needle length is 8 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
10-Zone SMT Reflow Oven
CR10000
-
10 fully controlled upper and lower convection heating zones allow the CR10000 SMT reflow oven to provide you with a thermal accuracy of ±1˚C. Manncorp’s low-velocity, low-turbulence air flow options produce an even ΔT of ±2°C across PCB assemblies out to 22” (570 mm) wide edge-to-edge backed by throughput that can still keep pace with your high-volume production needs.
-
Product
GB-GRAM/GB-GRAM-M Interface Card
Valiant 153M
-
Valiant 153M is a GB-GRAM/GB-GRAM-M (GB-GRAM/M) interface card that allows the simultaneous operation and testing of a commercial- off-the-shelf (COTS) receiver and a GB-GRAM/M. Both receivers are powered and communicate using a single USB mini cable. By integrating a COTS receiver onto the Valiant 153M, users can perform cross-checks to determine if the military receiver is connected and communicating data properly. Both receivers communicate via the onboard USB mini or RS-232 serial connectors. The Valiant test fixture was designed to be nearly the same size as the GB-GRAM/M type I card.
-
Product
USHIO Red Laser Diodes (633nm - 690nm)
-
The Optoelectronics Company Ltd
Features: 5.6 mm CAN package, Optical output power: 80 mW (CW), 300 mW (pulsed – pulse width: 10 ns, duty: 10%), Lasing wavelength: 658 nm, Wall-plug efficiency*: 33%, Operating temperature: -10° – +60° C (CW); -10° – +75° C (pulsed), Single transverse mode, TE mode oscillation, MTTF >10,000 hours
-
Product
cRIO-9043, 1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 4-Slot CompactRIO Controller
785620-01
Embedded Controller
1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 4-Slot CompactRIO Controller - The cRIO-9043 is a rugged, high-performance, customizable embedded controller that offers Intel Atom dual-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 160T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
Product
IEC61850-3 20GE + 8GE Combo L2 Managed Switch, 90 ~ 264VAC/88 ~ 370VDC
EKI-9228G-8COI
-
16 x Gigabit RJ-45 ports + 4 Gigabit x SFP ports + 8 x Gigabit Combo portsSFP socket for Easy and Flexible Fiber ExpansionManagement: SNMP v1/v2c/v3, WEB, Telnet, Standard MIBSecurity:802.1x (Port-Based, MD5/TLS/TTLS/PEAP Encryption),HTTPS,SSH and SNMPv3Redundancy: Gigabit X-Ring Pro (ultra high-speed recovery time < 20 ms), RSTP/STP (802.1w/1D),MSTPDual Power input and 2 relay output-40 ~ 85˚C wide-range operating temperature
-
Product
Digital Infrared Thermo Leak Detector
IR-711
-
Shenzhen Calibeur Industries Co., Ltd..
'-4 colors backlight to indicate thermo leak by diviation setting;'- Measurement Range: -40° to 716°F (-40° to 380°C); '- Accuracy : < 0°C： ±3% or ± 3°C ≥0°C： ±2% or ±2°C '- Distance Spot Ratio: 12:1; '- Emissive: fixed at 0.95;'- Response time: 0.5 seconds;'- ℃/℉ selectable;'- Three ranges of leak difference exchange: ±0.5℃, ±3.0℃, ±5.5℃ ±1℉, ±5℉, ±10℉'- Size: : 42*85*185mm'- Weight: 170g'- Power: 1pc 9V Battery .(not included)
-
Product
MIL-STD-1553 A / B Test And Simulation USB Module
USB-1553
-
*Dual redundant*1 or 2 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*More programmable triggers and acquisition*10 programmable I / O*Onboard IRIG-B timecode encoder / decoder*Supports stand-alone operation via USB connection, without external power supply*On-board battery for runtime without power supply
-
Product
Multi-Channel, Multi-Protocol 1553 and ARINC 1/2 Size PCIe 4-Lane Interface Card
PCIEC4L-MA4
Interface Module
Alta Data Technologies’ PCIEC4L-MA4 interface module is a multi-channel, multi-protocol 1553 and ARINC ½ size PCI Express 4 Lane interface card (PMC on 4 Lane PCI Express Carrier) is supported by the latest software technologies. The PCIEC4L card is based on the industry’s most advanced 32-bit FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
Product
Thermometer, -20°C to +400°C, 7.9 ", 2.7 ", 1.2 "
72-6700
-
Infrared Thermometer*Three thermometers in one...Infrared, Pt100 ohm and Thermocouple*Accommodates 4 wire Pt-100 ohm probes and thermocouple types K, J, R, T, and E.*Selectable readings °C or °F*Data Hold function*Min./Max memory function*Laser guide for IR function*RS 232 output*Auto power off
-
Product
sbRIO-9403, Non-Enclosed, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module
780539-01
Digital Module
Non-Enclosed, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module - The sbRIO‑9403 is a configurable digital I/O interface for input or output with shift‑on‑the‑fly capabilities. Each channel features transient isolation between the I/O channels and the backplane. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the sbRIO‑9403 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and other applications.
-
Product
Wireless MCU With Integrated Wi-Fi 6 And Bluetooth Low Energy 5.4
AIW-411
-
NXP RW612 Arm Cortex®-M33Integrated Wi-Fi 6 and Bluetooth® LE 5.4Rich Industrial I/O Interfaces:USB 2.0 OTG *1, PSRAM *1, Ethernet RMII *1, SDIO 3.0 *1, UART *2, SPI *1, I²C *2, PWM *3, JTAG *1, ADC *2NXP MCUXpresso SDK CompatibilityOSM Size-0 Compact Design (30 x 15 mm)
-
Product
High Temperature Axial Extensometers
-
4 models cover a variety of applications for high temperature testing1 un-cooled model for use inside chambers up to 600 °C (1000 °F)Other models for use with split furnaces and induction heating, up to 1600 °C (2900 °F)
-
Product
NI-9231 and cDAQ-9171 USB Sound and Vibration Measurement Bundle
865665-01
Sound and Vibration
NI-9231 and cDAQ-9171 USB Sound and Vibration Measurement Bundle - The USB Sound and Vibration Measurement Bundle with NI-9231 and cDAQ-9171 includes the NI-9231 C Series Sound and Vibration Input Module and the cDAQ-9171 CompactDAQ Chassis for sound and vibrations measurements. This bundle provides a portable, USB-based sensor measurement system that helps you measure signals from integrated electronic piezoelectric (IEPE) and non IEPE sensors such as accelerometers, tachometers, and proximity probes. The included NI-9234 features 8 channels with built-in anti-aliasing filters that automatically adjust to your sample rate. Additionally, the bundle supports simultaneous sampling and high dynamic range measurements necessary for modern measurement microphones and accelerometers.
