RF Detectors
Sense the presence of radio frequencies.
-
product
RF Detectors
RF detectors from Fairview Microwave are available with N Type or SMA connector series inputs and BNC or SMA connectors for outputs. Fairview RF detectors are zero bias Schottky diode and have negative video out. These zero bias Schottky diode detectors for RF have a minimum frequency between 10 MHz and 2 GHz and maximum frequency range between 2 GHz and 26.5 GHz.
-
product
RF Detectors
BroadWave designs and manufactures RF Detectors and other coaxial RF components that are ideally suited for test, verification and system integration. With frequency ranges of DC to 18 GHz, our components offer consistent performance at a low cost with an emphasis on performance and configuration flexibility.
-
product
RF Detectors for Millimeter Wave
RF Detectors are essential microwave/millimeter wave products for most Tx (transmit sources). Transmitter output power measurement is the main application. It is essential to know the RF output power because the output power level must not go above values set by FCC regulations.The unit of power is the watt for RF detectors. But, most commonly used in most RF and wireless systems to express power is the terms of dBm or decibels related to 1 mW:View more RF Detector
-
product
Bulk Current Monitoring Probe
MP-50
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
product
RF Signal/Wireless Camera/Mobile/Bug Detector
SH-055U8 / 01018
The RF Signal Detector / Wireless Camera Detector / Mobile Phone Detector / Bug Detector applies digit (numeric) display to show the sensitivity level. With up and down buttons, user knows the sensitivity setting directly
-
product
RMS Responding Power Detectors
Recognized as the pioneer and leader in RF detectors, Analog Devices offers a broad portfolio of high performance logarithmic amplifiers and TruPwr™ rms responding detectors. ADI logarithmic amplifiers measure signals up to 100 dB dynamic range, from dc to microwave, and accuracies of ±0.2 dB, and are well-suited for both RSSI and transmit power level detection. The TruPwr rms detectors address the challenge of measuring complex waveforms found in spread spectrum CDMA/W-CDMA and higher order QAM modulation systems and provide an accurately scaled dc voltage, which is the rms equivalent of the input waveform.
-
product
Level Detectors
Becker Nachrichtentechnik GmbH
Becker Nachrichtentechnik offers selective RF level detectors for air interface monitoring. The detectors are especially designed for frequencies used in e.g. electron accelerators. Due its mechanical design, the modules are compatible to cable route mounting systems. The detection of unintentional RF radiation is a main application field.
-
product
RF Proximity Detector
Type RPD-2 AND Type RPD-2A
The Type RPD-2 Radio Frequency (RF) Proximity Detector is designed to detect and locate devices that radiate radio waves in the high frequency to low microwave frequency range. Such devices often include surveillance and “spy” equipment. The Type RPD-2, when used with the different sensors, will detect the emanation of the radio wave within a confined area, and then isolate its location to within approximately a square foot. The type RPD-2A may be used as an RF field strength indicator for antenna field strength measurements. The RPD-2A is identical in function except that the meter scale is calibrated in relative dB units.
-
product
IoT Battery Life Optimization Solution
X8712A
The Keysight X8712A is an IoT battery-life-optimization solution that consists of a DC power analyzer, 20 W or 80 W battery drain analyzer source/measure unit (SMU) modules, RF event detector, and dedicated software in one integrated solution.
-
product
Cellular Phone/RF Signal/ Wired Camera/Bug Detector
SH-055GRV / 01125
This Cellular Phone Detector / RF Signal Detector / Wireless Camera Detector applies with fuzzy scanning technology to detect peeping cameras, tapping, cellular phones and other radio frequency devices
-
product
RF Signal Detector/Wireless Camera Detector
SH-055SRV / 10127
This "Wireless Camera Detector / RF Signal Detector / 2G Mobile Phone Detector" can detect the popular wireless CCTV camera, wireless phone, wireless tap and Cell phone from 50 MHz ~ 6.0 GHz.
-
product
Non-RMS Responding Power Detectors
Recognized as the pioneer and leader in RF detectors, Analog Devices offers a broad portfolio of high performance logarithmic amplifiers and TruPwr™ rms detectors. ADI logarithmic amplifiers measure signals up to 100 dB dynamic range, from dc to microwave, and accuracies of ±0.2 dB, and are well-suited for both RSSI and transmit power level detection. The TruPwr rms detectors address the challenge of measuring complex waveforms found in spread spectrum CDMA/W-CDMA and higher order QAM modulation systems and provide an accurately scaled dc voltage, which is the rms equivalent of the input waveform.
-
product
RF Power Detectors
Monitors or samples the output of an RF circuit and develops a dc output voltage pro- portional to the power at that point.
-
-
product
Selective RF Detector
Raksa iDet
RAKSA iDet detects: cellular phones of GSM900/1800, UMTS(3G), CDMA450 standards; cordless DECT phones; Bluetooth and Wi-Fi devices; wireless video cameras; radio transmitters with analog modulation (AM, FM, PM); radio transmitters with digital modulation and continuous carrier (FSK, PSK, etc.); radio transmitters with wideband modulation up to 10 MHz bandwidth.
-
product
Resonance Dip Meter
NRM-2
National RF’s Resonance Dip Meter is a test instrument used to determine the resonant frequency of a tuned circuit or resonant network, such as an antenna system. In addition, the unit may function as an RF detector, or a secondary frequency source. The instrument is analogous to the older vacuum tube “grid dip meter,” once popular in every electronic laboratory or radio station. Unique to this updated version is a buffered output that may drive a digital frequency counter for exact measurement of resonant frequency, or connected to an oscilloscope to be used as an RF detector and waveform/modulation monitor.
-
product
What is an RF Power Detector?
RF detectors are used in a wide variety of applications to measure and control RF power.Learn more on What is an RF Power Detector? at Precision website here.
-
product
Detectors - RF / Microwave
PMI offers a full line of RF and Microwave detector products that range from 2 MHz up to 40.0 GHz. Many options are available. If you do not see exactly what you require on this web site please contact
-
product
Lipstick size Camera/Signal Detector
SH-005 / 01018
This Mini Camera Detector / Wireless Camera Detector / RF Signal Detector is special made for detecting the peeping cameras and hidden caneras.
-
product
Cryocooler
CryoTel® DS30
The CryoTel® DS 30 Stirling cryocooler offers efficient, reliable, compact and high power cooling to the market in the temperature range of 35 to 250 Kelvin. The DS30 was optimized for applications in which SWAP (size, weight and power) and reliability are concerns. The DS30 consumes considerably less power than other cooling alternatives and requires no maintenance, making it ideal for strategic as well as industrial applications. Both the cold head and the pressure wave generator can be mounted in any orientation. Application examples include semiconductor manufacturing, large infrared detectors, RF receivers or antennas, astronomical telescopes, laser cooling, high-temperature superconductivity, cold traps, and others.
-
product
PXI Hex SPDT RF Switch, 8GHz 50Ω SMA, Terminated
40-880A-003
The 40-880A-003 is a hex SPDT 50Ω RF switch with 8GHz bandwidth. The 40-880A range of SPDT switches have automatic termination of unused signals and are available as a dual switch in a 1 slot PXI module, a quad switch in a two slot PXI module or hex and octal switches in three slot PXI modules
-
product
75Ω High Isolation LXI RF Multiplexer
Pickering's LXI high isolation RF multiplexers are suitable for switching 75Ω signals up to 1GHz - ideal for constructing complex microwave switching systems for many applications. These matrices are supported by a comprehensive range of cable and connector accessories and come with a standard 3 year warranty.
-
product
50 Ohm BNC to BNC Cable Assembly
40-977-501-2m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
Handheld RF Power Meter
V3500A
The V3500A Handheld RF Power Meter is a compact, handheld instrument that makes accurate RF power measurements in both field and manufacturing applications. With an absolute accuracy as good as 0.21dB, a wide frequency range of 10MHz to 6GHz, and a measurement range of -63dBm to +20dBm, the V3500A is suitable for a wide variety of RF measurement applications. Its built-in power sensor eliminates the need for users to carry both an instrument and a separate sensor module. Truly portable, the V3500A fits easily into your hand or a toolkit. An optional belt loop holster or carrying case with shoulder strap is also available. To optimize flexibility, it is capable of drawing operating power from batteries, an AC-DC converter module, or a computer via USB interface.
-
product
75 Ohm BNC to BNC Cable Assembly
40-977-701-1m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
75 Ohm SMZ/Type 43 Cable Assembly
40-977-711-0.1m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
PXIe-5654, 10 GHz or 20 GHz RF Signal Generator
783126-01
The PXIe‑5654 features an ideal combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe‑5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications.
-
product
50Ω uWave SMA 2.92 Cable Assembly, 40GHz, 1m
40-977-544-1m
50 Ohm uWave SMA 2.92 Plug to uWave SMA 2.92 Plug Cable Assy, 1m Long.
-
product
PXI Octal SPDT RF Switch, 8GHz 50Ω SMA, Terminated
40-880A-004
The 40-880A-004 is an octal SPDT 50Ω RF switch with 8GHz bandwidth. The 40-880A range of SPDT switches have automatic termination of unused signals and are available as a dual switch in a 1-slot PXI module, a quad switch in a 2-slot PXI module or hex and octal switches in 3-slot PXI modules.
-
product
NI-5781 , 40 MHz Bandwidth, RF Adapter Module for FlexRIO
781267-01
The NI‑5781 is an analog dual-input, dual-output FlexRIO adapter module optimized for interfacing with baseband to RF upconverters and downconverters. When you pair the NI‑5781 with a PXI FPGA Module for FlexRIO, the resulting NI‑5781R is an FPGA-enabled reconfigurable I/O (RIO) baseband transceiver that you can use to implement custom RF modulation and demodulation, channel emulation, bit error rate testing, or spectral monitoring and jamming. Additionally, you can use the low latency and high throughput of FPGA‑based processing for ultra‑high‑speed control and inline processing applications.
