-
Product
60 GHz WR-15 Waveguide Tx Module
PEM010
-
The PEM010 is a highly integrated millimeter wave transmitter that covers the 60 GHz global unlicensed spectrum allocations packaged in a standard waveguide module. Transmitter architecture is a double conversion, sliding IF with wide bandwidth capability through the up-conversion chain from baseband to carrier. The I/Q interface accepts analog baseband signals which provides for flexibility in design and applications. The baseband input optionally supports FSK/MSK modulation for non-coherent applications. The transmitter incorporates a complete waveguide interface with low-loss transition between the chip and the WR15 waveguide port. The integrated package is small and lightweight, with a simple to use multi-pin ST4 connector for power, reference clock, digital control port and baseband signals. Either of two reference clocks can be used for setting 540 MHz or 500 MHz channel spacing.
-
Product
Waveguide Power Detector
-
RF Lambda’s waveguide power detectors are used to convert the RF power level to a DC voltage for signal power measurement. They offer wide band operation, fast response time and compact size.
-
Product
Double Ridged Waveguide Horn
DRH370
-
Frequency range: 370 MHz - 6 GHz VSWR (max): < 1.6:1Impedance: 50 O (Ohm)Connector: N female Power (CW / Peak): 350W / 500 W
-
Product
Millimeter Wave Antenna Testing
-
If you are involved in antenna or system level design using mmWave or THz frequencies, then you understand the importance of dependable testing equipment. It may be that you are designing passive phase array or that you are designing a mmWave radar sensor system, but when it comes to validation of your design, simulation can only bring you so far. Phased array antennas have to be measured over the air (OTA) to ensure the radiation pattern of your design efficiently conducts energy in the right direction which is where the MilliBox comes in.
-
Product
Custom Waveguides
-
Custome waveguides for commercial, industrial, government and research & development industries. Consult with our engineering staff on your millimeter wave needs. View more Custom Waveguides
-
Product
Coaxial Waveguide Adapter, 1.0 mm (m), 50 to 75 GHz
V281D
-
The Keysight V281D is a 1-mm male to V-band waveguide adapter with a frequency range of 50 GHz to 75 GHz. The Keysight V281D is used with the Keysight 8510XF systems.
-
Product
Waveguide Harmonic Mixer, 75 to 110 GHz
11970W
-
The 11970W extends the frequency range of the Keysight N9030A PXA high-performance signal analyzer to the W-band (75 to 110 GHz). It is also fully compatible with other Keysight spectrum analyzers including: the E4440A/46A/48A PSA (with Option AYZ), the E4407B ESA-E (with Option AYZ), the 856xEC, the 8566B (with a preamplifier), and the 7000 modular analyzer (with the 70907A/B external mixer interface module).
-
Product
Millimeter Wave Antennas
-
Ducommun millimeter wave products include ACH, ARH and ALC series circular, rectangular gain horn antennas and lens corrected horn antennas for system applications. Low side lobes, ridged configuration and low cost are the main features of these antennas. The standard gain value and half power beamwidth at mid-frequency point of each waveguide band are 23 dBi and 9 degrees, respectively. Other gain values are available as customer order. These antennas cover the frequency range of 18 to 110 GHz.
-
Product
Waveguide Variable Attenuators
-
A variable attenuator from Pasternack. This SMA microwave attenuator is a continuously variable attenuator design.
-
Product
Waveguide Twists
-
Fairview Microwave’s precision waveguide twists operate from 18 to 110 GHz across seven frequency bands with waveguide sizes ranging from WR-42 (18 GHz) to WR-10 (110 GHz). Our portfolio of waveguide twists feature gold plated brass construction that offers excellent electrical performance with VSWR as low as 1.02:1 and insertion loss as low as 0.2 dB. Both 45° and 90° waveguide twists are available from stock, with the 45° versions being available in both right hand and left hand twist configurations. All of our waveguide twists are in-stock and ready to ship today!
-
-
Product
Coaxial Waveguide Adapter, 3.5 mm (f), 18 to 26.5 GHz
K281C
-
The Keysight K281C adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can be transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.07.
-
Product
Coaxial Waveguide Adapter, 2.4 mm (f), 33 to 50 GHz
Q281A
-
The Keysight Q281A is a 2.4 mm female to WR-22 waveguide adapter that operates in the 33 to 50 GHz frequency range. These adapters transform waveguide transmission lines into 50 ohm coaxial lines. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Double Ridged Waveguide Horn
QRH40
-
Frequency range: 4 GHz - 40 GHz VSWR (max): < 2.4:1Impedance: 50 O (Ohm)Connector: 2xK female Power (CW / Peak): 10W / 20 W
-
Product
Coaxial Waveguide Adapter, 1.85 mm (m), 40 to 60 GHz
U281B
-
The Keysight U281B adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Waveguide Cassette
-
Waveguide cassettes provide easy way for the network analyzer calibration and material properties as dielectric permittivity or (and) magnetic permeability measurements. By changing insertion sections, it is possible to calibrate "Short" and "Thru". Optional cassettes with quarter wave "short" inserters are available. Using this waveguide cassette, it is possible to do vector network analyzer calibration or additional scalar network analyzer calibration. Insertable sample holders supports two measurement methods: the rod in the centre of the waveguide and filled waveguide cross-section.
-
Product
Coaxial Waveguide Adapter, APC-7, 8.2 to 12.4 GHz
X281C
-
The Keysight X281C adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
K-Band Waveguide Gunn Oscillator Module
FMWGN1001
-
FMWGN1001 is a K Band Waveguide Gunn Oscillator with a Center Frequency of 24.125 GHz and a Tuning Range of +/- 1.0 GHz. The unit has a Phase Noise @ 100kHz Offset of -95 dBc/Hz typ and Frequency Stability of -0.4 MHz/°C max. The Gun Oscillator has an Output Power of 10 dBm min and Power Stability of -0.04 dB/°C max. The Waveguide Gun Oscillator uses a Bias Voltage of 5.0 Volts and a Bias Current of 200 mA and has a Waveguide Size of WR-42 with a UG-595/U Flange.
-
Product
Waveguide Harmonic Mixer (smart mixer), 50 to 75 GHz
M1971V
-
Keysight M1971V 50 to 75 GHz waveguide harmonic mixer is an un-preselected mixer that provides a complete solution for wideband millimeter-wave signal analysis of more than 2 GHz with X-Series signal analyzers. Embedded smart features help you to greatly simplify your overall test setup and improve the DANL and TOI of your test system. Go smart with harmonic mixing for your millimeter-wave applications.
-
Product
Coaxial Waveguide Adapter, 1.85 mm (m), 50 to 67 GHz
V281B
-
The Keysight V281B adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Waveguide Detector, 26.5 to 40 GHz
R422C
-
The Keysight R422C is an 26.5 to 40 GHz GaAs planar-doped barrier diode detector. This waveguide detector has negative output polarity.
-
Product
Coaxial Waveguide Adapter, 1.0 mm (f), 75 to 110 GHz
W281C
-
The Keysight W281C is a 1-mm female to W-band waveguide adapter with a frequency range of 75 GHz to 110 GHz. The Keysight W281C is used with the Keysight 8510XF systems.
-
-
Product
Millimeter Wave Spectrum Analyzer
-
Insight Product Co. offers the spectrum analyzer for frequency measurements of millimeter wave generators of continuous or pulsed signals. The spectrum analyzer can be ordered to cover a complete millimeter wave frequency band: 35-53 GHz; 53-78 GHz; 78-118 GHz; or 118-178 GHz and offer exceptional spectral resolution of 1-5 kHz.
-
Product
Straight Waveguide Section
-
Straight sections are used to make connections between components in waveguide systems. Lengths and combinations are available on special order. VSWR is better than 1.1 over the full waveguide frequency band. Precision flanges on special order.
-
Product
E Bend Waveguide
-
E-plane waveguide bends are sections of high-precision crafted waveguides and shaped to either 30º, 45º ,60º, or 90º angles for e-plane needs. It directs the radio frequency beam and “bends” the signal to go the direction you want. Think of it like Tokyo drifting around a corner in your car. Precision MMW will help you with the highest quality E bend waveguides. We are a millimeter wave spectrum manufacturer of various active and passive mmWave products and sub-system engineering.View more E Bend Waveguide
-
Product
Double Ridged Waveguide Horn
QRH11
-
Frequency range:730 MHz - 11 GHz VSWR (max): < 2.4:1Impedance: 50 O (Ohm)Connector: 2xSMA female Power (CW / Peak): 100W / 170 W
-
Product
Double Ridged Waveguide Horn
DRH18–E
-
Frequency range: 1 GHz -18 GHz VSWR (max / AVG): < 3:1 / 1.35:1Impedance: 50 O (Ohm)Connector: SMA female / N femalePower (CW / Peak): 50 W / 100 W
-
Product
Double Ridged Waveguide Horn
DRH50
-
Frequency range: 4.5 GHz - 50 GHz VSWR (max): < 1.55:1Impedance: 50 O (Ohm)Connector: 2.40mm female Power (CW / Peak): 10 W / 20 W
-
Product
Waveguides
-
Learn about waveguides at Precision MMW. This is a handy waveguide tutorial for the everyday mmWave engineer.Learn more on Waveguides at Precision website here.
