RF Voltmeters
Measures RF voltages on tuned circuits.
-
Product
PXI-2594, 2.5 GHz, 50 Ω, 4x1 PXI RF Multiplexer Switch Module
778572-94
Multiplexer Module
2.5 GHz, 50 Ω, 4x1 PXI RF Multiplexer Switch Module—The PXI‑2594 is ideal for applications that require the routing of high-frequency signals inside automated test equipment (ATE) systems because it can switch signals with very low insertion loss. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use the onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
Product
PXI Triple SPDT RF Switch SMB 75 Ohm
40-830-003
Switch Module
The 40-830-003 is a 75Ω RF Switch with 3 separate SPDT relays in a single PXI slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks have been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
PXI/PXIe RF Multiplexer, Dual 4-Channel, Terminated, 8GHz, 50Ω, SMA
40-882B-002
Multiplexer Module
The 40-882B-002 (PXI) and 42-882B-002 (PXIe) are dual 50Ω 4 to 1 RF multiplexers with 8GHz bandwidth.The 40/42-882B range has automatic termination of unused signals and are available as a single MUX in one slot, a dual MUX in two slots, or triple and quad MUXs in three slots.
-
Product
FieldFox C Handheld RF Analyzer, 4 GHz
N9913C
-
Capture elusive signals with up to 120 MHz gap-free, real-time bandwidth. Measure all four S-parameters simultaneously with 115 dB dynamic range. Make accurate spectrum analyzer measurements (± 0.3 dB) without warmup. Perform over-the-air measurements for 5G NR and LTE. Use GPS/GNSS for geolocation and timestamping.
-
Product
RF Electronic Calibration Module (ECal), DC/300 KHz To 26.5 GHz, 4-ports
N4433D
-
The Keysight N4433D RF electronic calibration (ECal) module makes calibration of Keysight vector network analyzers fast, easy and accurate. The N4433D is a precision 4-ports ECal module that supports selection of 3.5 mm connector and can be mixed up to 26.5 GHz. Select either female-female, male-male, or female-male connectors.
-
Product
RealProbe RF Probes
-
Unmatched performance In-Circuit RF Probes covering up to 18GHz. These are must tools for any in-circuit RF and Microwave testing and troubleshooting.
-
Product
PXI/PXIe RF Multiplexer, Quad 4-Channel, 3GHz, 50Ω, SMB
42-872A-004
Multiplexer Module
The 40-872A-004 (PXI) and 42-872A-004 (PXIe) are 50 Ohm 4 to 1 RF multiplexers available with 4 banks in a single PXI slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
RF Test
-
RF is short for radio frequency. RF is any frequency within the electromagnetic spectrum associated with radio wave propagation. When an RF current is supplied to an antenna, an electromagnetic field is created that then is able to propagate through space. Many wireless technologies are based on RF field propagation. These frequencies make up part of the electromagnetic radiation spectrum.
-
Product
PXI Dual 4 to 1 RF Multiplexer 2GHz 50 Ohm SMB
40-746-511
Multiplexer Module
40-740, 40-745 and 40-746 RF Multiplexers are a range of Bi-Directional Multiplexers with bandwidth up to 2000MHz.They are arranged as Single 8 to 1, Dual 4 to 1 or Single 4 to 1 configurations, all with excellent Insertion Loss, VSWR and Isolation, in 50 Ohm or 75 Ohm versions with a wide choice of connectors.Applications include routing high frequency signals to and from oscilloscopes, analyzers, signal generators and synthesizers, telecoms tributary switching (from 2MBit/s to 155MBit/s), video/audio switching and switching high frequency logic signals.
-
Product
HandyScope HS5: 50 MS/s 250MHz BW, 2 Channel, USB Digital Storage Oscilloscope, 5MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS5-055XM-W5
-
The Handyscope HS5 is the first USB oscilloscope (USB powered) sampling at 50 MHz, with a 14 bits resolution and a 250 MHz bandwidth. This makes it possible to analyze very fast signals with very small amplitudes. The smallest distortions can be revealed due to the high resolution and bandwidth. Because of the deep memory (up to 64 MSamples on one channel), long record measurements are available for intermittent phenomena and Fast Fourier Transform calculations with over 32 million spectral lines can be performed. Using very fast FFT algorithms, an FFT with 1 million spectral lines can be performed within a second.
-
Product
RF Signal Generators
-
The Lucid RF signal generator Series is geared towards solving applications demanding outstanding dynamic range, fast switching speed, and easy remote programming for seamless system integration, all in a compact module platform. The series was designed to offer industry leading price to performance ratio, delivering a full product portfolio for generating signals for various applications whether, 5G, radar, communications, and more.
-
Product
9GS/s 16Bit 8GS Mem 8CH 16 Markers RF AWG Benchtop
P9488B
Waveform Generator
The benchtop version of the Proteus arbitrary waveform generator series offers up to 12 channels in a 4U, 19” benchtop box. With a 9” touch display and on-board PC the benchtop platform enables users to program the instrument without the need of an external PC. Users can program the instrument from the onboard PC using various programming environments such as MATLAB, LabView, Python, and more. So for synchronized, phase coherent, multi-channel applications such as quantum physics and radar applications the Proteus arbitrary waveform transceiver is an ideal, high performance, and cost effective solution.
-
Product
PXI-2799, 40 GHz, 50 Ω, Dual SPDT PXI RF Relay Module
782359-01
Relay
40 GHz, 50 Ω, Dual SPDT PXI RF Relay Module - The PXI‑2799 is a general-purpose single‑pole double‑throw (SPDT) switch module for routing RF or microwave signals in automated test applications. You can use this module for basic signal routing or inserting and removing components in a signal path. The PXI‑2799 is also well-suited for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules. You can use its onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
Product
50 Ohm BNC to SMA Adaptor Assembly
40-978-511-1m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
PXI 8x4 RF Matrix 300MHz 50 SMB
40-729-001
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
PXIe-5652, 6.6 GHz RF Analog Signal Generator
781217-01
Signal Module
PXIe, 6.6 GHz, PXI RF Analog Signal Generator—The PXIe‑5652 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5652 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
PXI-2595, 5 GHz, 50 Ω, 4x1 PXI RF Multiplexer Switch Module
778572-95
Multiplexer Module
5 GHz, 50 Ω, 4x1 PXI RF Multiplexer Switch Module—The PXI‑2595 is ideal for applications that require the routing of high-frequency signals inside automated test equipment (ATE) systems because it can switch signals with very low insertion loss. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use the onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
Product
Noise Bridge, RF 1 MHz to 100 MHz
MFJ-202B
-
Quickly adjust almost any antenna for maximum performance, 1 to 100 MHz. Lengthen or shorten your antenna for minimum SWR. Measure resonant frequency, feedpoint resistance and reactance. Works with any receiver or transceiver. Hand-calibrated resistance scale, expanded capacitance range and exclusive built-in range extender.
-
Product
PXI/PXIe RF Matrix, 16x4, 100 MHz, 75 Ω SMB
40-727A-101
Matrix Switch Module
The 40-727A-101 (PXI) and 42-727A-101 (PXIe) are 16x4 75 Ω RF matrices with SMB connectors. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
Product
RF Cable Assemblies
-
Radiall's extensive range of RF cable assemblies features outstanding electrical performance, low loss and high frequency. The range includes flexible, semi-rigid, corrugated and hand-formable cable assemblies with a combination of RF cables and connectors optimized for each market or application. Custom RF cable assemblies are also available.
-
Product
HandyScope HS4 DIFF: 10 MS/s 100MHz BW, 4 Channel, USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS4-10-DIFF
-
The Handyscope HS4 is the successor of the popular Handyscope HS3. Built for customers that want to extend their measuring capabilities even further, this powerful computer controlled measuring instrument now features four input channels. The HS4 has just like it's predecessor the four main measuring instruments: a Multimeter, an Oscilloscope, a Spectrum analyzer and a Transient recorder.
-
Product
PXI Dual 4 to 1 RF Multiplexer 2GHz 75 Ohm 1.0/2.3
40-746-731
Multiplexer Module
40-740, 40-745 and 40-746 RF Multiplexers are a range of Bi-Directional Multiplexers with bandwidth up to 2000MHz. They are arranged as Single 8 to 1, Dual 4 to 1 or Single 4 to 1 configurations, all with excellent Insertion Loss, VSWR and Isolation, in 50 Ohm or 75 Ohm versions with a wide choice of connectors.
-
Product
Protable AC/DC Voltmeter
ST-2000 V
-
Standard Electric Works Co., Ltd
● Principle : Moving coil type● Accuracy : ± 0.5% F.S.● Scale Length : Approx. 135mm(5-3/8”)● Weight : Approx. 1.7kg● Dimension :196(L) x 170(W) x 87(D)mm● Case Material : Bakelite with glass window
-
Product
PXI/PXIe RF Multiplexer, Single 4-Channel, 3GHz, 75Ω, MCX
40-832A-101
Multiplexer Module
The 40-832A-101 (PXI) and 42-832A-101 are 75 Ohm 4 to 1 RF multiplexers with 1 bank in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
PXI Dual 4 to 1 RF Multiplexer 3GHz 50 Ohm MCX
40-874-102
Multiplexer Module
The 40-874-102 is a 50 Ohm 8 to 1 RF multiplexer with 2 banks in a single PXI slot. It has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths of the 40-874 has been minimized by careful attention to the mechanical and electrical design.
-
Product
PXI/PXIe RF Switch, Hex SPDT, 3GHz, 50Ω, MCX
40-870A-106
Switch Module
The 40-870A-106 (PXI) and 42-870A-106 (PXIe) are 50Ω RF switches with 6 separate SPDT relays in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The injection of noise and unwanted signals into the signal paths of the 40/42-870A has been minimized by careful attention to the mechanical and electrical design.
-
Product
RF Filters
-
Raymond RF offers a complete line of RF filters ranging from 0.4A to 600A in both stand-alone and cabinet-mounted configurations for our QuietBoxes and Anechoic Chambers. Both styles of filters can be supplied with NPT pipe nipples and flange nuts for mounting directly on a QuietBox or Anechoic Chamber. Alternately, both styles of filters can be remotely mounted with shielded conduit running between the clean end of the filter and the QuietBox or Anechoic Chamber.
-
Product
PXI/PXIe RF Matrix, 16x2, 300 MHz, 50 Ω MS-M Multiway
40-728A-002
Matrix Switch Module
The 40-728A-001 (PXI) and 42-728A-001 (PXIe) are 16x2 50 Ω RF matrices with SMB connectors. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
Product
Handset Noise Under RF Test System
BK8021
-
If you need to evaluate the resistance of cellphones to RF interferance, the BaKo Type BK8021 Handset Noise Under RF Test System is what you need. It performs four tests to evaluate the Sending Noise, Sending Sensitivity, Sending Loudness, Sidetone Masking, Receiving Sensitivity and Receiving Loudness. You run the system using the controlling PC, which allows automatic configuration and which runs the test sequence automatically. When testing is complete, you can print the data as an MS Excel report or save it for comparison and analysis.
-
Product
100MHz, 2 Channel ISA Oscilloscope, Spectrum Analyzer, Transient Recorder, Voltmeter & Abitrary/Function Generator
TP801-AWG-ISA
-
The TP801 AWG is the first ISA card based 100 MS/second measuring instrument that consists of a Voltmeter, Oscilloscope, Spectrum analyzer, Transient Recorder and an AWG (Arbitrary Waveform Generator).
