SCSI
"Small Computer System Interface" defines a communication standard for connecting peripheral devices and thier controllers to a microprocessor.
See Also: Parallel Interfaces, UFS
-
Product
Cable Assembly, Receiver, TriPaddle, 20", 68-Pin Male SCSI
540007010103
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 20", 68-Pin Male SCSI
-
Product
16 Bit PXI I/O Board With 32 Or 64 Analog Outputs
CP266
-
The CP266 is a single-width, 6U, CompactPCI module with 32 or 64, 16-bit analog output channels. These independent analog channels provide ±10 V full-scale outputs. The channel update rate is 2ms, and each output is accurate to ±1mV. The power-up state of the analog outputs can be set to independent user-defined values. Paired output signals are provided to eliminate ground offset effects. The analog outputs are available at a single 68-pin SCSI II shielded connector (32-channel option) or a pair of 68-pin SCSI II shielded connectors (64-channel option).
-
Product
96-Pin Male SCSI to 96-Pin Female SCSI Switch Cable
150275-01
Switch Cable
96-Pin Male SCSI to 96-Pin Female SCSI Switch Cable - The SH96F-96M SwitchBlock SCSI Cable provides connectivity for SwitchBlock modules. You can connect these to the TBX-2809 Terminal Block, which exposes each channel of the switch module to screw terminals.
-
Product
PXI 18 Channel Data Comms MUX, 96-pin SCSI
40-735-902
Multiplexer Module
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
96-Ch Digital I/O PCIE Card
PCIE-1753
Isolated Digital I/O Card
Fully compatible with PCI-1753Up to 96 TTL digital I/O linesEmulates mode 0 of 8255 PPISupports both dry and wet contactInterrupt handling capabilityOutput status read-backSupports input data pattern match and change of state functionsKeep I/O settings and output status after hot resetBuffered circuits for higher driving capacity than the 8255High-density 100-pin SCSI connector
-
Product
PXI Resistor Module Dual 16 Bit With 16XSPDT Relays
40-290-121
Programmable Resistor Module
The 40-290 Series Programmable Resistor Modules comprise a Dual 16-bit or Quad 8-bit resistor chain together with 16 optional SPDT Reed Relays. Connections are made via a front panel SCSI 2 type 68 pin male connector. Programmable resistors may be connected together either in series or in parallel to form many types of configuration.
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to PCB-Mounted 1x100 Pin Female SCSI Connector
510150127
PCB Adapter
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to PCB-Mounted 1x100 Pin Female SCSI Connector
-
Product
2 X 1 SCSI Switch For Rack Mount Or Tabletop
MODEL SS1
-
The SS1 SCSI Bus Switch allows two hosts to share peripherals or one host to access either of two sets of peripherals. Each port may be SE, HVD or LVD. Switching from one port to the other may be accomplished: a. locally with the front panel switch, b. remotely with a momentary dry contact closure, or c. remotely via the RS-232 port. A software template for the RS-232 port is included in the User Manual. In all cases switching does not occur until "bus free."
-
Product
Cable Assy 68-Pin SCSI Micro-D M/M 0.5m
40-970-068-0.5m-MM
Cable Assembly
The 68-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28AWG) Copper Wire with Polypropylene insulation. Metal Spring Latches are provided to secure the connectors to their associated products.
-
Product
96-Pin Micro-D Connector Block, Female With Screwlocks
40-965-096-F
Connector Block
This connector block provides a simple method of connecting to 96-Pin SCSI Style Micro-D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
Product
SCSI Toolbox Tape Manufacturing Module
Tape Manufacturing Module
-
SCSI Toolbox LLC is proud to announce the Tape Manufacturing Module addition to the SCSItoolbox, joining a decade of real-world tape drive testing experience with input from hundreds of customers to bring the best new testing tool to the tape manufacturing and integration marketplace. The Tape Manufacturing Module is the easiest to use, most versatile, and fastest tape testing product on the market.
-
Product
Hand-Held SCSI CABLE TESTER
ST1000
-
The ST1000 SCSI Cable Tester is designed with an emphasis on simplicity of use. Connect a cable, press a switch and the LCD indicates the test results within 5 seconds. In addition to Continuity and Integrity, the ST1000 also tests to determine that the critical REQ and ACK signal pairs are located in the inner layers of the cable.
-
Product
68-Pin SCSI Micro-D Conn Block DIN
40-966-068-M
Connector Block
Suitable for mounting on DIN Rails this connector block provides a simple method of connecting to 68-Pin SCSI Style Micro D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
Product
68-Pin SCSI Micro-D M to 2x34 0.5m
40-971-068-0.5m-MF
Cable Assembly
The 68-Pin SCSI Style Micro-D Cable Assembly is constructed from 2x34-Pin Twisted Pair cable with PVC insulation, terminating with 2x34-Pin polarised IDC connectors. Strain relief is provided via a metal spring latch on the 68-Pin connector.
-
Product
Cable Assembly, Receiver, TriPaddle, 20", 96-Pin Female SCSI
540003010103
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 20", 96-Pin Female SCSI
-
Product
68-Pin SCSI Micro-D Male Connector Block
92-965-068-M
Connector Block
This connector block provides a simple method of connecting to 68-Pin SCSI Style Micro-D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage.
-
Product
SHC68-68-EPM, 68-Pin Male VHDCI to 68-Pin Female D-SUB, Twisted Pair, Shielded Multifunction Cable, 0.5m
192061-0R5
Multifunction Cable
Connects to DAQ devices and modules, terminal blocks, bare wires, or other accessories. The multifunction cable models include a variety of industry-standard front- and back-end connectors, such as 68-pin VHDCI, 96-pin SCSI, and 68-pin SCSI. Cable selection depends on the connector types and requirements of the hardware you’re connecting to and the environment in which you’re using the cable. Some cables are internally twisted and shielded to more effectively reject ambient noise than an ordinary shielded cable. These cables are designed to work with high-performance NI devices.
-
Product
PXI Resistor Module Quad 8 Bit
40-291-021
Programmable Resistor Module
The 40-290 Series Programmable Resistor Modules comprise a Dual 16-bit or Quad 8-bit resistor chain together with 16 optional SPDT Reed Relays. Connections are made via a front panel SCSI 2 type 68 pin male connector. Programmable resistors may be connected together either in series or in parallel to form many types of configuration.
-
Product
SHC68-68-A2, 68-Pin Male VHDCI to 68-Pin Female SCSI, 1m Cable
157599-01
Multifunction Cable
SHC68-68-A2, 68-Pin Male VHDCI to 68-Pin Female SCSI, 1m Cable. For use with the PXIe-6738 and PXIe-6739.
-
Product
Cable Assy 68-Pin SCSI Micro-D M/F 0.5m
40-970A-068-0.5m-MF
Cable Assembly
The 68-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28AWG) Copper Wire with Polypropylene insulation. Metal Spring Latches are provided to secure the connectors to their associated products.
-
Product
Cable Assy 68-Pin SCSI Micro-D M/M 0.5m
40-970A-068-0.5m-MM
Cable Assembly
The 68-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28AWG) Copper Wire with Polypropylene insulation. Metal Spring Latches are provided to secure the connectors to their associated products.
-
Product
Cable Assy 68-Pin SCSI Micro-D F/F 0.5m
40-970-068-0.5m-FF
Cable Assembly
The 68-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28AWG) Copper Wire with Polypropylene insulation. Metal Spring Latches are provided to secure the connectors to their associated products.
-
Product
High Speed Device & Flash Programmer
JT 2147 QuadPOD
-
The JT 2147 QuadPOD high speed device programmer and flash programmer comprises JT 2148 transceiver and four independent, programmable JT 2149 TAP PODs and provides signal conditioning for the DataBlaster series of boundary-scan controllers. Used for gang, parallel, fast testing / Programming of devices.TAP pods can be housed integrally within the transceiver or they can be detached and reconnected via the (optional) one meter extension cable. The JT 2148 transceiver is available in standard (/10) or industrial (/13) variants. The /13 variant includes a SCSI cable splitter to allow system integrators to use flat ribbon cables into the transceiver itself which often simplifies fixture building.A fixture-embedded variant of the JT 2147 is available as part reference JT 2147/FXT. This unit integrates the function of the transceiver and four pod onto a single assembly. This variant can also support 64 DIOS channels and SCIL functions (see more images below for a picture of the JT 2147/FXT).
-
Product
Cable Assembly, 100 Pin Male SCSI to 100 Pin Male SCSI, Twisted Pair, Double Ended, 18"
515109134
Multifunction Cable
Cable Assembly, 100 Pin Male SCSI to 100 Pin Male SCSI, Twisted Pair, Double Ended, 18"
-
Product
Cable Assembly, 68 Pin Female SCSI (Thumb Screws), to 68 Pin Male SCSI (Spring Latch), 18"
515109119
Cable Assembly
Cable Assembly, 68 Pin Female SCSI (Thumb Screws), to 68 Pin Male SCSI (Spring Latch), 18"
-
Product
Cable 100-Pin Micro-D Male to Unterminated, Cut Ends, 0.5m 2-56 UNC Screwlocks, Metal Shell
A100SMR-C-9A050
Cable Assembly
This 0.5m long male to unterminated 100-Pin SCSI Style Micro-D Cable Assembly is suited for direct connection to various products using the 100-Pin connector. It is constructed from 100-Pin twisted pair cable with varying left and right hand lays to minimise crosstalk. The Cable is colour coded to ensure easy connection. Screwlocks are provided to secure the SCSI connector to its associated product.
-
Product
Cable 96-Pin Micro-D Female to Female, 2m
40-970B-096-2m-FF
Cable Assembly
The 96-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. Metal Spring Latches are provided to secure the connectors to their associated products.
-
Product
SHC68-68-A2, 68-Pin VHDCI Male to 68-Pin SCSI Female Analog Cable
157599-02
Multifunction Cable
SHC68-68-A2, 68-Pin Male VHDCI to 68-Pin Female SCSI, 2m Cable. For use with the PXIe-6738 and PXIe-6739.
-
Product
96-Pin SCSI Micro-D Right-Angle PCB
40-963-096-RM
SCSI Male PCB Mount
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
Cable Assembly, Receiver, QuadraPaddle, 20", 100-Pin Male SCSI
540009010140
Cable Assembly
Cable Assembly, Receiver, QuadraPaddle, 20", 100-Pin Male SCSI
