-
product
Line-impedance stabilisation network
NNB 21 set
The NNB 21 line impedance stabilization network is designed for measuring of grid bound interferences of a device under test according to the satndard CISPR 25/ISO 7637. It measures the RF interference, which couples into the vehicle electrical system. Measurements during the development in a frequency range from 100 kHz to 1GHz can be carried out.
-
product
Network Forensic Analysis
nChronos
nChronos is a Network Forensic Analysis Application for high performance & critical enterprise networks. It combines nChronos Console and nChronos Server to deliver the capability of 7*24 continuous packet capturing, unlimited data storage, efficient data mining and in depth traffic analysis.
-
product
End-to-End Network Monitoring
OSIX
Network monitoring with tracing and troubleshooting capabilities to achieve first-class customer experience and to proactively prevent network and service quality degradation. OSIX Monitoring enables Communication Service Providers (CSPs) to detect and resolve network issues or poor performance before end-customers are affected.
-
product
Streamline Vector Network Analyzer, 9 KHz To 4.5 GHz, 4 Or 6-port
P5020B
Compact, faceless, vector network analyzer (VNA). Flexible four or six-port VNA dramatically reduces your size of test. Up to 4.5 GHz.
-
product
Streamline Vector Network Analyzer, 9 KHz To 6.5 GHz, 2-port
P5001B
Compact, faceless, vector network analyzer (VNA). Flexible two-port VNA dramatically reduces your size of test. Up to 6.5 GHz.
-
product
Network Analysis Solution
IOTA
IOTA is a complete network analysis and troubleshooting solution for a variety of use cases in small, mid-size enterprises, remote sites, and small data centers. It is a versatile integrated solution, combining TAP, storage, and analysis capabilities in a single portable device.
-
product
Network Analyzer, Lan Tester, LED
72-6706
The Tenma Multi-Network and Modular Cable Tester easily reads the correct pin configuration of 10Base-T cable (Category 5, 5e and 6), 10Base-2 cable (coax), RJ-45 and RJ-11 modular cables, 356A, TIA-568A/568B and Token Ring cable by comparing transmitting end to the corresponding receiving end
-
product
Basic Pulsed-RF Measurements Lite For E5081A — Up To 44 GHz
S960241B
Add pulsed-RF measurement capabilities to your E5081A ENA-X vector network analyzer.
-
product
PacStar IQ-Core Software
Curtiss-Wright Defense Solutions
Our PacStar IQ-Core® Software provides an intuitive user interface that makes communications setup and operation quick and easy to learn. It reduces configuration errors by assisting organizations in maintaining uptime, performance, and compliance with cybersecurity requirements, and simplifies troubleshooting with tools for both entry-level and advanced network administrators.
-
product
UDP Test Tool, Flood Generator, VoIP Readiness Test Tool
The Multiprotocol Network Tester is a freeware, open source tool which enables you to measure quality of your IP network. It can also be used to generate UDP flood or to simulate UDP DoS attack. SIP call is usually established using a SIP session with a bidirectional RTP stream. SIP and RTP protocols are based on UDP transport protocol. UDP uses a simple transmission model without implicit reliability, ordering and data integrity. Each single UDP packet is transferred independently. The quality of a SIP call depends on delays and loss of IP packets in a network. Long delays lead to large RTP jitter and bad sound quality of a SIP call.
-
product
Test Port Cable, 1 Mm
11500J
The Keysight 11500J test port connector has a length of 16 cm and a frequency range of DC to 110 GHz. The 11500J integrates with the Keysight N5250A network analyzer and Keysight 8510XF network analyzer systems.
-
product
Wireless Soil Monitoring Network
AquaMon
Reduces Water Costs While Maintaining or Improving Crop. Yields Reduces Electrical Costs by Minimizing Pumping Requirements. Reduces ongoing Operating Costs by Eliminating Manual Data Retrieval. Adapts to Multiple Soil Types, Terrain Variations and Micro-climates.
-
product
Mobile Measuring & Testing Systems
Individual testing tasks for technical plants and large machines often require the use of a large number of measuring instruments on site, which are difficult to network with each other and which, in the case of complex measurements, require a lot of experience and time in operating the measuring equipment and analysing the recorded measured values. The applications and possible uses can be quite different:
-
product
Versatile Sensor Network
Information System Technologies Inc.
ISTI offers a versatile, scalable and easy to use distributed sensor network solution for high fidelity data acquisition and development platform, allowing users/developers to test their signal processing and data fusion algorithms. The system supports multiple sensing types including acoustic, seismic and IR/scanning laser. Among the key capabilities of ISTI’s versatile sensor network are: (a) sensor-level hardware/software to provide configurable sampling and synchronization, on-board processing and storage for low to intermediate-level signal processing and data acquisition; (b) network-level solutions that account for network connectivity and sensor-network health monitoring and support various routing strategies; and (c) system-level console that allows users to select and upload application tasks. Users can choose several modes of operation to examine various factors such as reliability, bandwidth, and data timeliness.
-
product
SMA-Male to N-Male Test Cable
C50SMNM
Our 2N-to-SMA test cable is made to ideally suit our larger line of vector network analyzers. The C50SMNM operates at a frequency of 18000 MHz and is compatible with select family lines of vector network analyzers including our Compacts, Full Size, and Cobalt analyzers.
-
product
MCCI Catena® 4450 Node for LoRaWAN™ Technology
The MCCI Catena® 4450 Node for LoRaWAN™ technology is a powerful open-source IoT device designed specifically for use with The Things Network. Based on the Adafruit Feather M0 system, the Catena 4450 is a ready-to-use platform for LoRaWAN 1.0 and 1.1 wireless IoT applications.
-
product
Network, Port ID And Cable Tester
One for All PH-400
The One For All is an all-in-one network tester, tone generator, cable tester, and port ID finder. It comes with a remote unit, allowing pin-by-pin tests of installed cables in addition to patch cables. The office ID feature allows the user to check the ID number of up to 100 networks or patch panel outlets without labeling the cables manually, and the tone generator traces cable using a tone detectable by any market tone probe. The network tester blinks the network hub or NIC port light for the cable being tested, allowing easy cable and outlet identification; and it identifies network speed (10 Mbps vs. 10/100 Mbps vs. 10/100/1000 Mbps) and activity. Line tester included for detect live circuits and preventing damage to the tester.
-
product
Fault Locator
BIDOYNG
BIDOYNG fits into existing LV fuse positions using two LV fuses in parallel, creating a robust single-shot auto-recloser. The primary fuse carries the load current until a fault causes it to operate. Then, after a user programmed delay, the secondary fuse is switched in and the network re-energised without customer interruption.
-
product
PXI 16 x SPDT Reed Relays
40-110-021
The 40-110/115 range of switching modules are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 96 pin male micro-D connector. General purpose reed relays are used for the construction of small switching networks or for slaving up to larger switches.To simplify inter-relay wiring, interconnection points are built onto the circuit board thus easing the construction of complicated wiring.
-
product
Managed Hub
HUB-5595
The HUB-5595 is a managed hub designed to operate with the Abaco Systems 5565 family of Reflective Memory real-time network products. The Reflective Memory hub can automatically bypass ports when it detects a loss of signal or the loss of valid synchronization patterns, allowing the other nodes in the network to remain operational.
-
product
cDAQ-9189, 8-Slot, TSN-Enabled Ethernet CompactDAQ Chassis
785065-02
8-Slot, TSN-Enabled Ethernet CompactDAQ Chassis - The cDAQ-9189 is a CompactDAQ Ethernet chassis designed for distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. With this chassis, you can combine C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis provides precise, synchronized timing over the network using TSN, ideal for highly distributed measurements over long distances. The chassis has an integrated network switch for simple daisy-chaining. The chassis also has four 32-bit general-purpose counters/timers, accessible through a hardware-timed digital C Series module for applications that involve quadrature encoders, PWM, pulse train generation, and more.
-
product
10-Port Layer 2 Managed/Unmanaged Ethernet Switches
TEN710MW
*EN 50155 layer 2 managed Ethernet switch*Power boost for PoE+, max. budget 150W*Wide operating temperature range from -40°C to 75°C*Supports ERPS/QoS/LACP and more network control, and security features*Reliable IP54 & 5 years warranty
-
product
Digital Processor
DP7000
The DP 7000 Digital Processor with 40/100G Ethernet or 169G Interlaken protocol compatible MPO/MTP® Optics, designed for evolving markets such as Real-Time Stream Processing for High-speed Data-acquisition (DAQ), High Performance Computing (HPC), Machine Learning, Data Center Infrastructure, AI Processing and Network applications. The board is 8U form factor, 322.25 mm x 280 mm x 6 HP (L x W x H), single slot AXIe or AdvancedTCA® blade, ideal for multi-slot 19″ rack mount system integration. In AXIe form factor it provides up-to Gen3 PCIe® backplane connectivity.
-
product
4-in-1 OSLT Calibration Kit, DC to 50 GHz, 2.4 mm (m)
CK564A
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
product
±6 kV ANSI/ESDA/JEDEC HBM Test System
HBM-TS10-A
High Power Pulse Instruments GmbH
*±6 kV Human-Body-Model (HBM) tester according ANSI/ESDA/JEDEC JS-001 standard with C = 100 pF, R = 1.5 kΩ discharge network*Wafer, package and system level HBM testing*True HBM: the classical discharge network of the HBM-S1-A according the standard ensures compliant waveforms for all load conditions*No trailing pulses*Integrated 10 kΩ charge removal resistor*Integrated DUT HBM current sensor for real time transient current monitoring with 1V/A output sensitivity into 50 Ω digital oscilloscope input*Integrated DUT HBM voltage sensor for real time transient voltage monitoring with 1/200V/V output sensitivity into 50 Ω digital oscilloscope input*Integrated overvoltage protection of the DUT voltage sensor, DUTcurrentsensor and DC test interface for efficient overload protection of the digital oscilloscope and SMU during high voltage HBM testing*Integrated DC test DUT switch with automatic switch control*Integrated 50 Ω precision hardware trigger output for high speed digital oscilloscopes*Fast HBM measurements, typically 0.5s per pulse including one-point DC measurement between pulses*Eficient sofware for system control and waveform data management (fully compatible with TLP measurement data)*The sofware can control automatic probers for fast measurements of complete wafers*Compact size 145 mm x 82.5 mm x 44 mm of the integrated HBM pulse generator probehead*System controller size 483 mm x 487 mm x 133 mm*High performance and high quality components*Optionally available hardware upgrades to all HPPI fully integrated HBM/HMM/TLP/VF-TLP test systems TLP-3010C, 4010C, 8010A, and 8010C
-
product
VMware Monitoring & Management
Hyperic HQ
Hyperic HQ for VMware is a pioneering new solution that enables data centers to consolidate complete discovery, monitoring, analysis and control of all application, system and network assets, both inside and outside of the virtual machines powered by VMware.
-
product
Optical Fiber 1×8 Switch
OFSW - 1 × 8
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW- 1×8 is a 1×8 prism optical switch. It can support 1 optical fibers input and 8 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
product
Insulation Tester
Cambridge Instruments & Engineering Co.
'CIE' Insulation Tester is a compact portable unit incorporating most modern features used for direct reading of electrical operating machines, Rotating Plant equipment, Stationary apparatus, Insulation Control switching equipment, Distribution networks, Communication cables, Insulators, Transformers, Industrial Installations, Cable, electrical components, wiring and other devices capable of carrying the rated voltages.
-
product
Air Interface Emulator
Becker Nachrichtentechnik GmbH
With help of air interface emulators radio field propagations can be emulated reproduceable in laboratory environments. For different applications like cellular, wireless networks or broadcast several types of devices are available.
-
product
Embedded Components
Teledyne Labtech prides itself in being at the forefront of RF/Microwave PCB development. Teledyne Labtech were also one of the first companies to successfully develop techniques for embedding SMD resistors and capacitors within multilayer structures and the embedding of connector pins in buried stripline circuits.The advantages of such a structures ensures a much higher density of interconnect. This then removes the need for via-hole connections to the board surface or the need to create access pockets to the inner layers. Consequently you finish with a board with that exhibits much lower RF/Microwave losses. This is particularly important when designing large RF feed networks or 16:1 power dividers.
