Multimode Fiber
Optical fiber capable of supporting more than one mode of light propagation.
-
Product
RF over Fiber Link TX/RX
L-Band
-
QuestTel's Satellite L-Band optical fiber Transmitter/Receiver set offers high pefromance and cost effective alternative to conventional coaxial systems. The L-Band Transmitter and Receiver pair is used for transporting L-Band RF over fiber from the antenna to the satellite receiver. Additionally transmitter provides optional 13/18V LNB power as well as Automatic Gain Control (AGC) to manage RF input level. By transporting the L-Band RF over fiber this range can be extended from several hundred feet to over 80 miles. Since optical signal is not affected by electromagnetic field, the quality of your signal will always stay at the high level. Also this fiber solution is more cost effective than coaxial system, as well as more reliable and flexible.
-
Product
C & L-Band Separate Raman Fiber Amplifier
RFA7000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
4FE+1FE SC Multi-Mode Unmanaged Ethernet Switch, ATEX/C1D2, -40~75℃
EKI-5525MI
-
Communicates with SCADA software via Modbus/TCPCommunicates with NMS (Networking management system) via SNMPPort-based QoS for deterministic data transmission8.4~52.8 V DC wide-range power inputEMS level 3 protection for extreme outdoor environmentsIEEE 802.3az Energy Efficient Ethernet (EEE)Jumbo Frame Support (Up to 9,216 Bytes)Supports redundant 12~48V DC power input and P-Fail relayLoop detection
-
Product
MXI-Express Cable, Gen 1 x1, Fiber Optic, 200m
778959-200
MXI Express
MXI-Express Cable with Communication Levels up to Gen 3 x8 - The MXI-Express Cable connects a host interface to a PXI or PXI Express chassis. You can also use it for data communication between multichassis systems. NI offers it in different MXI communication levels and lengths.
-
Product
4FE+1FE SC Multi-Mode Unmanaged Ethernet Switch
ADAM-6521
Ethernet Switch Module
Provides 4 x 10/100 Mbps Ethernet ports with RJ-45 connector and 1 x 100 Mbps multi/single-mode fiber port with SC/ST connector, Supports full/half duplex flow control, Supports Integrated Loop-up engine. Supports MDI/MDI-X auto crossover, Provides broadcast storm protection. Supports +10 ~ 30 VDC voltage power input.
-
Product
ULI-213E - Heavy Industrial RS-232/422/485 (Terminal Block) To Single Mode Fiber (SC Connector) Panel Mount Metal Chassis
BB-FOSTCDRI-PH-SC
-
Converts serial data signals to multi- or single-mode fiber, SC connector2 KV, 3-way isolation (input, output, power circuits)Data rate: 9.6 to 115.2 kbps (bit-wise enable)-40 to +85°C wide operating temperatureIP30 metal panel mount case (DIN rail adaptable)FCC, CE, IEC-61850-3, IEEE 1613, UL C1/D210-48 VDC power source required (not included, sold separately)Note: 2 units required to extend data via fiber optic connection (see datasheet)
-
Product
In-Line Isolator Single Stage 1310nm Bare Fiber 250μm Without Connector
IL-S-31-25-05-OO-3422
-
Guilin GLsun Science and Tech Group Co., LTD
Center Wavelength1310 nmPDL＜0.1 dBPMD0.25 psDimensionΦ3.4×22 mmOperating Temperature-5 to +70°CStorage Temperature-40 to +85°C
-
Product
High Power Fiber Optic Visual Fault Locator
VFL-700
-
Shanghai Fibretool Technology Co.,Ltd.
The VFL-700 is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in an optical network during and after installation.
-
Product
Multimode Data Controller
PK-232/PSK
-
Timewave’s customers swear by their DSP filters and PK-232 owners love the flexibility and reliability of the most popular data controller ever built. Now with the addition of a sound card interface, the PK-232/PSK rolls it all into one! The PK-232/PSK brings a new level of performance to the legendary PK-232 with sharp, accurate DSP filters for all its internal data modes and dual transformer isolation for sound card data modes. Weak signals magically appear from the noise and QRM bounces off the new DSP filters for cleaner copy with fewer errors than the old analog filters.
-
Product
Fiber Inspection and Cleaning
-
Dust - just because you can't see it doesn't mean it's not there. A 1-micrometer dust particle on a single-mode core can block up to 1% of the light (a 0.05dB loss). The only way to know it's clean is to inspect it before you connect it. And if it's dirty, it needs to be cleaned with the right tools or you might just make it worse. Know it's clean with our cleaning and inspection tools.
-
Product
Fiber Optic Tool Kits
-
SYOPTEK has done fiber optic tool kit assembly for the fiber optic industry for over 8 years, from fiber optic cleaning kit to fiber optic tester kit, from fiber optic inspection kit to fiber optic splicing kit...providing kits that meet varying needs of customers, and withstand the rigors of field fiber optic application use.
-
Product
Single Mode Fiber Test Kit
KI-TK077
-
Single mode fiber test kit for low to medium test volume on SM and MM systems.
-
Product
Fiber Optic Inspection Microscope
80760
-
The Miller 200x Microscope helps inspect fiber optic connectors quickly and easily. Its ergonomic design and built-in features make it ideal for field and lab use. The microscope features a pressure-activated on/off switch, focusing wheel, eyepiece, auxiliary white LED light source rated for 100,000 hours, adapter tip for inserting ferrule and battery compartment.
-
Product
PXI/PXIe MEMS Optical Switch, Quad Insert/Bypass, Single-Mode, 9/125 Fiber, LC Connectors
42-860A-442
Switch Module
The 40/42-860A-442 is a PXI/PXIe quad insert/bypass switch with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
PXI/PXIe MEMS Optical MUX, Dual 2-Channel, Single-Mode, 9/125 Fiber
40-855A-322-HI
Multiplexer Module
The 40/42-855A-322-HI is a PXI/PXIe dual 2-channel multiplexer with MU connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
MIL-STD-1553 Fiber Optic Bus Extender
FO-1553
-
Avionics Interface Technologies
Extends MIL-STD-1553 bus access to over 1 mile for remote access - Dual redundant, single and dual stream options available - Both Transformer and Direct coupling modes supported - Uses fiber optic 1.0625 Gbps data rates for low latency over long distances - Optical signaling is not affected by electrical noise and interference - Simple and easy to use solution, no software setup or configuration required - Ideal for applications where test equipment is separated from UUT
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 62.5/125 Fiber, ST Connectors, With Interlock
42-850A-514-M62.5-HI
Multiplexer Module
The 40/42-850A-514-M62.5-HI is a PXI/PXIe 4-channel multiplexer with ST connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Fiber Racks & Cabinets
-
Wuhan Sunma Technology Co., Ltd.
Optical Distribution Frame (ODF) is integrated components in any fiber management system to handle termination and cross-connection of cables. Pre-terminated ODFs with cables are pre-installed with connectors and cable for quick and easy installation. Units with pre-terminated cables offer advantages such as faster installation, resulting in shorter time to revenue as well as guaranteed quality and performance. SunmaFiber offer optical distribution frame in different size, such as 1U 12 ports, 1U 24 ports, 2U 36ports, 3U 48 ports, 4U 72 ports. Several cable options are available.
-
Product
Single 4 Ch Fiber Optic Multiplexer
40-810-114
Multiplexer Module
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or mult- mode fiber.A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
Product
Throwdown Fiber Transport & Converters
NanoBriX Series
-
We often forget all that happens along the media signal journey. Video and audio signals are converted, equalized and re-clocked as they move on and off fiber-optic networks. These same signals are manipulated and multiplexed as they are distributed through studio, venue and campus infrastructure on their way to headends and destination points. Audio signals are embedded and de-embedded alongside video streams, and properly mixed for varied broadcast and playout services. It’s almost too much to keep up with. MultiDyne’s NanoBrix Series assures that these many stages of the signal lifecycle are reliably addressed in one complete family. NanoBrix offers a comprehensive product line of miniature, rugged, quick-connecting throwdown solutions for temporary or permanent applications, including live TV productions, sporting venues, and broadcast facilities.
-
Product
Integrated Solution for Digital Switching & Fiber Optics Operational Verification
VERTA
-
When incorporated into defense/aerospace ATE, Verta enables reliable, error-free bus communication and interoperability tests to verify performance of high-speed, optically networked military weapon assemblies.
-
Product
Fiber Monitoring System for Optical Networks
-
Detecting serious physical network infrastructure issues like accidental fiber cuts, intrusion attempts, and malicious tampering has never been easier than utilizing this Fiber Monitoring System available from M2 Optics. The first solution approach in the industry that was designed to minimize monitoring costs on a per-fiber basis, all the hardware and software are integrated into a single low-profile chassis for fast deployment to cover your critical links.
-
Product
Dual Port Fiber 25GbE Ethernet PCI Express Server Adapter With NVIDIA® ConnectX®-6. Ideal For Data Center Networking And Storage Area Networks.
PCIE-2521NP
-
NVIDIA® ConnectX®-6 Lx Controller2 25GbE SFP28 portsPCIe Gen. 4 x8 host interfaceLow profile (half length) form factorsSupports 25GBASE-R, 10GBASE-SR and 10GBASE-LR modulesSupports SR-IOV based virtualization
-
Product
Automatic Fiber Jacket Stripping Machine - FBT-3000
-
Shanghai Fibretool Technology Co.,Ltd.
The FBT-3000 automatic fiber peeling machine is a new type of optical cable end processing equipment, which is based on the eagerness of optical fiber connector manufacturers to improve production efficiency and reduce the skilled manual emergence of optical cable end processing equipment. In order to solve the problem that the skin layer of optical fiber is usually peeled manually with wire peeling pliers, and the artificial denudation is low in precision, low in working efficiency and low in product quality.
-
Product
PXI/PXIe MEMS Optical Switch, Quad Insert/Bypass, Single-Mode, 9/125 Fiber, MU Connectors
42-860A-342
Switch Module
The 40/42-860A-342 is a PXI/PXIe quad insert/bypass switch with MU connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
-
Product
Fiber Optic Light Source
-
A device that emits controlled light signals (such as LEDs or lasers) into fiber optic cables.
-
Product
Fiber Optic Strain Sensors
-
Opsens Solutions optical strain sensor delivers reliable results in harsh environment. Opsens Solutions OSP-A fiber optic strain transducers are designed to provide accurate deformation measurement in the most adverse conditions. Its small size and EMI/RFI electromagnetic environment and lightning immunity makes it the ideal sensor for geotechnical, structural health monitoring, Defense and aerospace and general applications.
-
Product
PXI/PXIe MEMS Optical MUX, Dual 2-Channel, Single-Mode, 9/125 Fiber, LC Connectors
40-855A-422
Multiplexer Module
The 40/42-855A-422 is a PXI/PXIe dual 2-channel multiplexer with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
Fiber Optics
-
Blonder Tongue Laboratories, Inc.
Blonder Tongue has a comprehensive line of robust fiber optic transmitters and receivers for optical networks delivering both broadband CATV and data within campus-style environments with up to 1000 MHz bandwidth.
