Battery Electrical
-
Product
High Voltage Benchtop Battery Tester 1000V Max input
BT3564
-
Hioki benchtop battery testers support simultaneous high-speed measurement of the internal resistance and battery voltage of EV and PHEV battery packs. The BT3564 Battery HiTester can measure pack voltage and total resistance, as well as bus bar resistance up to 1000V.
-
Product
Electrical Circuit / Wire Harness Analyzer
ECAD System 2005
-
The ECAD System 2005 is a suite of test instruments for both lumped and distributed data for analysis of electrical circuits and/or wiring harnesses. ECAD is completely self contained, and has a built-in multimeter, impedance meter, TDR, and megohmeter.
-
Product
Safety Shoe Electrical Resistance Tester
UI-FT06
-
Safety Shoe Electrical Resistance Tester is to test the electrical resistance of conductive footwear and antistatic footwear.
-
Product
IEC60335-1 Electrical Inclined Plane Device
CX-100
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60335-1 Electrical Inclined Plane Device is designed and manufactured in accordance with IEC60335-1 clause 20.1. The IEC60335-1 Electrical Inclined Plane Device is to determine the stability of electric appliances which are used on a table or on the floor. The IEC60335-1 Electrical Inclined Plane Device consists of a surface and an angle adjusting device, with angles 0~15° adjustable.
-
Product
Battery Resistance Tester
FBR-6100NT
-
Fuzhou Fuguang Electronics Co., Ltd.
FBR-6100NT Battery Resistance Tester is a new generation handheld battery tester of FUGUANG™, which can quickly,intuitively and conveniently judge the deterioration of batteries (lead-acid batteries, lithium iron phosphate batteries and nickel-cadmium batteries, etc.). It has the characteristics of high accuracy, repeat consistency and anti-interference. It is an ideal tool for rapid battery daily check.
-
Product
Heavy Impact Tester, Battery Safety Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's battery impact tester tests the safety of the battery through different weights, different heights and different impact areas. After a series of tests on this battery impact tester, the battery must not have flame or explosion.
-
Product
Electrical Safety Test Solutions
-
Hipot Analyzers with 500VA output rating can be used to test and analyze the withstand voltage of high power and leakage current for the products like motor stators and rotors with high parasitic capacitance. Corona detection can be used for turn-to-turn or turn-to-ground test to avoid winding insulation failure from corona discharge.
-
Product
Shock Test System, Battery Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's shock test system used to measure and determine the impact resistance of a product or package. It is mainly used to evaluate the reliability of the function and the integrity of the structure of the test product under impact environment. Suitable for impact testing of aerospace, aerospace, marine, military, consumer electronics, automotive, household appliances and display equipment.
-
Product
PCI Express® Electrical Performance Validation and Compliance Software
D9040PCIC
-
D9040PCIC PCI Express Transmitter Test Compliance Software for PCI Express 4.0 (PCIe 3.x, 2.x and 1.x also supported).
-
Product
*Electrical Test And Measurement
-
GTC designs and manufactures a variety of electrical test and measurement tools.
-
Product
Battery Pack PCM Test Equipment
-
Xiamen WinAck Battery Technology Co., Ltd.
This battery PCM/PCB test equipment is suitable for the basic parameter test and protection function test of lithium battery pack protection board of mobile phone & digital products; it is also used for downloading, comparing and PCB calibration of battery management.
-
Product
RV Protocol Trailer Light and Electric Brake System Tester
RVCHECK
-
The RVCHECK is a fast, easy, low-cost way to test RV lighting and electric braking systems. In addition to powering an RV trailer's lighting circuits for easy checking, your RVCHECK measures the current draw of the electric brake coils, and checks the break-away battery circuit.
-
Product
12/24/36V Conductance Battery Tester
MBT200
-
Tests 12V heavy-duty auto, truck, commercial, and marine batteries and 12/24/36V starter and charging systems including 42V mild hybrid systems. Eliminate tester input errors by choosing between automotive/truck battery or small automotive type batteries. LED bar graph immediately displays battery condition upon pressing TEST button. No conversion tables needed for CCA, SAE, IEC, EN or Ah. 390 to 650 CCA range (auto) and 650 to 1700 CCA range (truck).
-
Product
Semiconductor Electrical Test
-
We conduct electric property test (final test) of the completed (packaged) LSI products. We will support testing of analog devices, logic devices, other electronic parts, modules, application products and so on. We will test according to customer's specification regardless of evaluation, trial production, mass production, by know-how cultivated with long-time mass production results. Test initial examination ~ From consistent correspondence up to selection and evaluation, individual correspondence such as design only is accepted.
-
Product
EIS Battery Analyzer
BA8100
-
The BA8100 is designed to accurately measure the internal impedance of a single cell or battery stack with voltages as high as 80 V. In addition to impedance, auxiliary measurements include voltage, current, phase, capacitance, inductance, quality factor and more. With the provided software, the BA8100 can perform Electrochemical Impedance Spectroscopy (EIS) across a frequency range of 50 mHz to 10 kHz. The impedance spectrum can be evaluated through the Nyquist and Bode plot tools to determine effective series resistance (ESR) and track battery health. Included with the BA8100 is a self-test fixture to verify the instrument’s performance or compensate for resistance introduced by the test leads.
-
Product
Electrical Test Tool
-
Beijing GFUVE Electronics Co.,Ltd.
Electrical testers are useful to check for voltage, continuity, shorted or open circuits, and improper wiring.
-
Product
Electric Burn-in Board Carts
-
Conforms to SEMI ergonomic standards Holds and transports card cages for semi-automatic loading/unloading. Holds up to 10 burn-in boards. Raises and lowers the burn-in boards for easy loading/unloading of boards into ovens or onto test benches. Cart can be adapted to dock with any Micro Control oven.
-
Product
Battery Charger-Analyzer for small battery systems
Minicharger
-
The Minicharger is an instrument designed to charge, trickle charge and analyze (discharge) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries
-
Product
Electrical Safety Testing
-
Manufacturers and operators of electrical equipment are required to carry out an electrical safety test within the framework of the applicable regulations. This is to prevent accidents caused by malfunctions in electrical equipment, such as fire, explosion as well as injuries and personal damage. The tests to be carried out are specified in national (VDE/DIN) and international (EN/IEC) standards. After passing the test, the product is considered safe for the entire life cycle, provided it is left in its original condition and used for its intended purpose.
-
Product
Battery Analyzer
UBA5-30V
-
The UBA5-30V can analyze up to 30V battery packs (33 for lithium ion or lithium polymer). It comes with a small power supply (120VAC or 220VAC input) that powers the UBA5's internal circuitry.
-
Product
Digital Electrical Network Analyzer
4126 NA
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● 2 Lines × 16 Characters LCD.● Auto-ranging / Auto-off.● One Push Button Operation.● Low Consumption.● Better than 3% Accuracy(0.05-50Ω).● Wiring Integrity Check(display + LEDs).● Over temperature protection and indication.● Stores previous readings.
-
Product
NI's Electrical Functional Test Solution
Functional Test
PXI instrumentation ensures complete and accurate test coverage with a modular architecture mounted in ultra-reliable PXI chassis.TestStand and LabVIEW software provide rapid development of complex test steps and sequences. PXI systems conserve floorspace because of their small, light form factor. Order them preassembled and installed using NI ATE Core Configurations.SystemLink™ software deploys updates and democratizes data insights to optimize operational efficiency.
-
Product
Battery Internal Resistance Tester
FST-7000
-
Foresight Electronics Co., Ltd.
Battery Conductance Tester is a portable digital measurement device for testing lead acid stationary batteries health and aging condition precisely within seconds. With the help of this device either single cells / blocks or large, multi group battery banks can be measured within a short time and the precisely measured data are processed and reported by given analyzer software automatically.
-
Product
Battery Testing
BTS 200
-
This testing and maintaining battery system allows to perform measurement of battery voltage, discharging current test and testing of battery capacity. BTS 200 can be connected with external load unit ELU 200.
-
Product
Testing of Electrical Safety
-
Manufacturers and operators of electrical equipment are required to carry out an electrical safety test within the framework of the applicable regulations. This is to prevent accidents caused by malfunctions in electrical equipment, such as fire, explosion as well as injuries and personal damage. The tests to be carried out are specified in national (VDE/DIN) and international (EN/IEC) standards. After passing the test, the product is considered safe for the entire life cycle, provided it is left in its original condition and used for its intended purpose.
-
Product
Battery Analyzers
Beta D-50
-
*Analyzer for any type of battery.*Adjustable constant current discharge from 0 to 50 Amps.*Set for Amp-Hour capacity reading.*Accept or Fail lights Indicators for a GO/NO-GO Test.
-
Product
Power Bank Battery Testing System
BTS4000
-
Shenzen Neware Electronic Co LTD
Battery testing system for power banks(BTS-4000-6V4A-CCDC-USB) is based on Neware BTS4000, it shares all the main feature of BTS4000, such as 0.05%FS accuracy, 10Hz data acquisition frequency, based on Ethernet communication, etc.
-
Product
Battery Pack Testing Equipment
-
Xiamen WinAck Battery Technology Co., Ltd.
The battery pack testing equipment is suitable for the testing of basic functions and protection functions of high-power finished battery packs. Such as lithium battery pack of power tools, garden tools, electric bicycles, backup power supplies, medical device and other products.
-
-
Product
Battery Tester 12V Language
BT12L
-
The Battery Tester 12V Language (BT12L) is an inexpensive, simple and easy tool for testing automotive batteries. It has LED display that consumes very little current and will not drain the battery with repeated testing.
