-
Product
Test & Evaluation
-
Scientific Research Corp. STI Division
Test & Evaluation has been a core capability since the company was founded. Our efforts in T&E span from test range capabilities development to test execution and data analysis, with emphasis on joint service capabilities.
-
Product
5G Radio Test Set
-
Operating from 20 to 40 GHz, two radios may be connected to the system allowing full duplex operation. Each radio may operates over identical Air Interface with uni or bi-directional multipath. The delays between radios may be varied from 0 to 1 mile in 5 foot steps with propagation loss control. The 2040+ creates a variable test range right in your lab. It can be used as a design aid and as a test tool for new modulation and encryption schemes prior to expensive and time consuming field testing.
-
Product
Anti-Freeze Tester
AFT-2
-
For testing methanol and ethylene glycol. With green and white scales. Green scale should be used when the engine is hot and white scale should be used when the engine is cold. Testing range: - Methanol - 40°C - 12°C, Ethylene Glycol - 34°C - 12°C. Manufactured with a glass tube, PVC bulb and spout
-
Product
Relay Pro 12-24V Relay Tester
60150
-
Tests relays by simply clipping the test leads onto the relay terminal pins using a 12 or 24v DC power source. Tests a wide range of 4 and 5 pin relays. Including shielded, nonshielded, relays with different pin sizes and 4 pin normally closed relays that other testers may incorrectly show fail. Automatically determines the relay configuration so the fully insulated gator clips can be connected in any order. Eliminates guesswork because you don’t need to connect to specific pins, like other testers. 45" power leads with heavyduty gator clips provide a secure connection to the power source.
-
Product
Digital Multimeter
MDM-5500 Series
-
A multimeter provides 5 1/2 digits, high-performance AC and DC measurements. The multimeter is equipped with a 3.7-inch color display with higher resolution and built-in intelligent operation system, and is able to provide more information and functions, simpler operation, wider testing range and more flexible and convenient system building. It is a new digit multimeter that leads the development tendency above.
-
Product
Package Test
-
WinWay’s commitment to technology, quality and service ensures our interface solutions go above and beyond to exceed your expectations. Our products and services have a proven track record of delivering customer success in semiconductor testing. The Company offers comprehensive test interface solutions ranging from wafer-level test, package-level test to thermal management.
-
Product
Material Testing Software
TRAPEZIUM X
-
Windows 10 compatible TRAPEZIUM X can carry out various tests ranging from simple test control to complex custom-made patterns, using the industry's first data search and preview function, free layout reports, visual wizard settings, quick panel, and quick conditions lists.
-
Product
DC Resistance Tester
ZLD-10
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-4; Inspection standard: JB/T4279.2-2008Used to measure conductor with nominal diameter ≥0.01～9.0mm or various round or flat copper and aluminum wires and other metal wires with DC current resistance of 100μΩ～99.99Ω;Combination of intelligent DC conductor resistance measuring meter and DC resistance test fixture with sample straightening function;Test range can be selected according to the resistance value of sample, and after clamping samples current resistance value would be displayed;Both potential fixture and current fixture are made of copper;The application of microcomputer control allows for full-automatic completion of test;LED will intuitively display measurement results;
-
Product
Battery String Simulator
BSS
-
AMETEK Programmable Power, Inc.
The Elgar Battery String Simulators (BSS) provide safe, reliable battery power for spacecraft testing. The broad range of features available ensures simulation capabilities for more than just two terminal power. It's the ideal solution for complete integrated system testing, not just battery elimination.
-
Product
Servopulser Fatigue And Endurance Testing Machine
EHF-E Series
-
This is the standard electrohydraulic servo fatigue testing machine, offering outstanding stable performance. It is capable of carrying out tests ranging from static tests to fatigue tests.
-
Product
Digital Insulation Testers
-
Built-in PV dedicated function 600 V AC/ 1000 V DC meter 5 test voltage ranges from 50 to 1000 V Comparator function Integrated hard carrying case
-
Product
Flash Memory Test System
T5830
Test System
T5830 memory tester, the latest member of its T5800 product family, optimized for testing a wide range of flash memory devices used in mobile electronic devices. The highly flexible T5830 tester has all of the capabilities needed to perform wafer sorting and final testing of price-sensitive flash memories.
-
Product
Medium-size Compact Antenna Test Range
H-Series CATR
-
The H-Series CATR chamber provide complete 3D performance assessment for 5G OTA devices and antennas including gain, efficiency, directivity, polarization and beam characteristics for frequencies from 3 up to 110 GHz, capable of supporting forthcoming 5G Sub-6 GHz (from 3 to 6 GHz) and mmWave (24 to 110 GHz) standardized testing including TRP/TIS, EIRP, EIS, IBB and emissions in accordance to 3GPP TR38.810 and TR37.842.
-
Product
Rockwell Hardness Tester
-
The most popular and widely used method of Hardness Testing, The Qualitest range of Rockwell Hardness Tester Range start from low cost analog models up to sophisticated and advanced load-cell type models. The popular, HardRocker, QualiRock, Rocky series hardness tester models have configurations suitable for Regular and/or Superficial Rockwell Hardness Testing, while our advanced Universal Hardness Tester Range can test the full Rockwell scale in addition to Brinell & Vickers. Qualitest also offers Automatic In-line hardness testers for high volume testing.
-
Product
Video Pattern Signal Generator
Model A223800/01/02/03/04
Signal Generator
Support 8K Super Hi-Vision (7680x4320/8192x4320)Independent graphics core for 8K Super Hi-Vision pattern with less than 200 msec. switch timeUp to 4 signal modules per unitUp to 4 resolution and pattern outputs.7 inch 1024x 600 high-resolution touch panel, GUI interfaceBMP file format supportUSB 3.0 data accessGigabit Ethernet high-speed network interfaceHDMI 2.0a signal module (Optional) - 8K x 4K 60 Hz (4 HDMI port) - 4K x 2K 60 Hz (1 HDMI port) - Pixel rate up to 600MHz (6Gbps TMDS rate) - RGB 4:4:4 / YCbCr 4:4:4 or 4:2:2 or 4:2:0 - HDCP 2.2 / 1.4 - Wide color gamut (ITU-R BT.2020/DCI-P3) - HDR (High Dynamic Range) Testing (HDR infoframe & metadata / EOTF) - SCDC (status & control data channel) Reader
-
Product
Cooled MWIR High-Sensitivity Camera
FLIR GF335
-
If you need a mobile camera that can detect extremely subtle temperature differences, the FLIR GF335 Broadband is the camera for you. The GF335 is a high sensitivity, low noise, cooled thermal camera that excels at detecting faint heat signatures. It is well suited to a wide range of applications, including use on test ranges, non-destructive testing, research, and science applications.
-
Product
Precision Impedance Analyzer (20Hz to 10MHz)
ST2839
-
ST2839 series precision impedance analyzer is a new generation impedance test instrument by adopting the current international advanced automatic balance bridge principle. Its basic accuracy of 0.05%, the fastest test speed of 5.6ms, the frequency range of 20Hz-10MHz, and the impedance test range of up to 1GΩ can meet the testing requirements of components and materials, especially for low-loss (D) capacitors and high-quality Measurement of Factor (Q) Inductors. The four-terminal pair port configuration method can effectively eliminate the influence of the electromagnetic coupling of the test line, and expand the lower limit of the low-impedance test capability ten times lower than that of the conventional five-terminal configuration instrument.
-
Product
Faster fault diagnosis
Rx Series
-
Based on the award-winning PHABRIX Sx handheld test & measurement range, the rack-mounted Rx series delivers advanced 2K/3G/HD/SD signal generation, analysis and monitoring for faster compliance testing and fault diagnosis of video and audio. Video capture speeds intermittent fault finding, and remote access offers monitoring from any location.
-
Product
Averaging Clip-on Extensometer
2650 Series
-
The Instron 2650 Series Biaxial Extensometers are ideally suited for testing a wide range of materials, including polymer matrix composites, metals, and plastics over a range of temperatures. Two sensors measure axial strain on opposite sides of the specimen. Versions are available which provide either a single averaged axial output or 2 independent axial outputs. The extensometers meet the calibration requirements of ASTM E83 class B1, ISO 9513 class 0.5, and ISO 527.
-
Product
Compact EMC Test Chamber
EMC-3C
-
This compact 3 meter test range will settle into test areas of limited space while continuing to produce exceptional performance for EMC measurement. Emission quiet zones of up to 1.5m are accommodated with very repeatable results. Suitable for EMC pre-compliance emissions and compliant immunity testing.
-
Product
Low Voltage Cable Tester
1100R+
-
The 1100R+ bench top cable tester packs impressive capabilities into a package that is small, affordable, and intuitive. The large display and sensible button interface make cable testing quick and easy. Test Point Range: 128-1024, Test Voltage: 5VDC 6mA max current.
-
Product
EMI Receiver
KH3935
-
Beijing KeHuan Century EMC Technology Co,.LTD
KH3935 type EMI test receiver interference test receiver is fully automatic, is EMI major tool for testing. The frequency range of the KH3935 receiver is from 9kHz to 30MHz , which satisfies the power line disturbance power test. After configuring the artificial power network, the power terminal disturbance voltage test can be performed. The machine has fast test speed, strong maneuverability, stable performance, Advantages such as convenient test data processing.
-
Product
PV-IV Solutions
-
We offer a broad range of PV IV Measurement systems for measuring solar cells from 3 mm to 300 x 300 mm. The wide range of solar simulators, vacuum chuck test stations, and electronic loads make it impossible to list “standard solutions” Most systems are put together for individual customer needs based on cell type and contact geometry of the devices being tested. Over the last several years we have designed and manufactured a wide range test solutions for many different types of cells and contact geometries. In most cases a customized solution is no more than a slight customization of a standard platform that has been previously designed.
-
Product
Material Testing & Physical Testing
-
Meeting the specifications put out by testing equipment manufacturers is critical when conducting quality control testing. We carry a wide variety of materials testing and physical testing products that are ideal for quality control testing along with research applications, letting you evaluate and test materials such as plastics, coatings, and chemicals. Physical properties testing products range from force and torque instruments, to hardness and thickness gauges, to viscometers and spectrometers.
-
Product
Package Testing Equipment
-
Dongguan Kejian Instrument Co., Ltd.
Bursting strength tester is ideal for testing a wide range of materials like paper, paperboards, corrugated board and boxes, leather, filter cloth, rexine, ect, to determine their quality, strength and performance.
-
Product
High-Speed MWIR Science-Grade Camera
FLIR X6980™
-
The FLIR X6980 is an extraordinarily fast midwave IR camera designed for scientists and engineers who need to capture high-speed imagery for accurate thermal analysis and custom radiometric measurements. This thermal imaging camera combines 640 × 512 resolution with blazing-fast frame rates, allowing researchers to record stop motion on fast-moving subjects or rapid temperature changes—whether in the lab or on the test range. With a four-position motorized filter wheel and support for FLIR motorized focus lenses, the X6980 will provide higher quality recordings, save time, and mitigate frustration in dynamic acquisition environments.
-
Product
Continuity of Insulation Tester (High Voltage Method)
ZGQ-16B
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-5;Inspection standard: JB/T4279.13-2008Meet GB/T6109-2008 standard requirementsUsed to test the Insulation continuity (namely the pinhole number of enameled wire sample per unit length) of enameled round wires with nominal conductor diameter ranging from0.05mmto1.60mm;8 level test voltages can be selected by pressing button: 350V, 500V, 750V, 1000V, 1500V, 2000V, 2500V and 3000V;Test length ranging 0～99m;Application of SCM control.Automatically complete test process, display wire testing length and pinhole number;Brushless driving motor, guide pulley and take up pulley are equipotent.The electrode insulation to ground, using high resistance material of non-hygroscopic, no leakage, no tracking, easy to clean, Insulation thickness can ensure long-term 3000V voltage effect.Circuit board is subject to anti-static and moistureproof and long-time aging treatment, has more stable quality and higher durability;
-
Product
Peel Testers
-
Imada offers motorized peel testers in vertical or horizontal configurations.The motorized test stand, digital force gauge and peel fixture apply tension to a safety seals, tapes and laminates.Special attachments and fixtures facilitate 45°, 90°, 180°, ‘T’ and rotary peel tests.Motorized peel testers offer speed control and highest degree of repeatability with the ability to set a constant test speed and range of movement.All peel testers with digital force gauges have data output capability for analysis by optional data acquisition software.
-
Product
Large Range Resistivity Tester
HS-SFRT
-
HS-SFRT silicon filament resistivity tester is an advanced silicon cylinder resistivity tester, which can measure silicon filament, silicon phosphorus ingot, silicon boron ingot, seed crystal and so on. As it eliminates Peltier effect, Seebeck effect, minority carrier inject effect and so on, So it improve the accuracy greatly. The testing resistivity ranges from 0.0005Ω·cm to 50000Ω·cm. It is accurate, stable and convenient and a good friend to Siemens polysilicon material producer, SH4 polysilicon material producer, UMG polysilicon material producer and so on.
-
Product
Leeb Hardness Testers
-
Your product description goes here. Leeb hardness tester application: Leeb hardness tester is for metal. Die cavity of molds,Inspection of bearing and other mass produced parts on a production line,Failure analysis of pressure vessel, steam generator and other equipment, Inspection of installed machinery, permanent parts of assembled systems and heavy work pieces.Rapid testing in large range and multi-measuring areas for large-scale work piece.
