Showing results: 466 - 480 of 577 items found.
-
10736A -
Keysight Technologies
The Keysight 10736A Three Axis Interferometer is used in multiple axis applications where linear and angular control of the stage is required. It combines in a single package the functionality of an optical bench with multiple beam benders, beam splitters, and three interferometers. The interferometers split an incoming laser beam into three beams to measure linear distance, pitch and yaw, or linear distance, roll and yaw. Three linear measurements provide the basis for calculating two angular measurements. The inherent beam parallelism ensures that there is essentially no cosine error between the three measurements and also ensures angle accuracy for pitch and yaw measurements. Other characteristics include:
-
10735A -
Keysight Technologies
The Keysight 10735A Three Axis Interferometer is used in multiple axis applications where linear and angular control of the stage is required. It combines in a single package the functionality of an optical bench with multiple beam benders, beam splitters, and three interferometers. The interferometers split an incoming laser beam into three beams to measure linear distance, pitch and yaw, or linear distance, roll and yaw. Three linear measurements provide the basis for calculating two angular measurements. The inherent beam parallelism ensures that there is essentially no cosine error between the three measurements and also ensures angle accuracy for pitch and yaw measurements. Other characteristics include:
-
UTP 5065 -
NOFFZ Computer Technik GmbH
Radar sensors are core elements to realize autonomous driving. The UTP 5065 radar test system from NOFFZ Technologies has a compact vertical design and contains everything needed to allow State-of-the-Art measurement and sensor calibration. The test bench setup and component selection are tuned to get best possible results for highly accurate and cost-efficient testing in production of automotive radar sensors.
-
HBM, Inc
HBM force sensors and force transducers measure static and dynamic tensile and compressive loads - with virtually no displacement. Your force load cell can be supplied in the most varied of designs and classes of accuracy. Typical force measurement application areas include bench testing, e.g. force measurement to check material quality and automation technology, e.g. for monitoring quality during reshaping or bonding operations.
-
CI Systems Inc.
CI Systems provides a wide range of laser testers, whether stand-alone systems, such as Depot Field Laser Tester, Depot Laser Tester or integrated in a multi-sensor electro-optical test bench. These testers can also be integrated with CI Systems' standard Laser Tester software and PC package to serve as the necessary testing tool for a larger system comprising a Laser Range Finder, Laser Marker and Laser Designator.
-
KPM Analytics
Vision inspection systems use a series of high-speed cameras and imaging software to detect and measure random objects as they move along a conveyor belt. Custom software and measurement algorithms can determine the size, shape, color or composite measurement of any object and convert this into standard units for quality control. Bench, over-line, and in-line systems are available and provide real-time 100% inspection and rejection of any production line.
-
PXIe-S5090 -
Copper Mountain Technologies
The PXIe-S5090 delivers metrology-grade VNA performance and speed to National Instruments’ PXI system. This high-performance vector network analyzer allows testing of two-port devices from the bench to the production floor in a compact, modular form factor. With 138 dB dynamic range and +13 dBm maximum power, this VNA is engineered for short time to first measurement and also for high performance automation with fast test times.
-
300 Series Benchtop ATE -
Circuit Check, Inc.
The Circuit Check 300 Series benchtop ATE Test Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 300 Series Benchtop ATE, test procedures can become automatic, with test steps and go/ no-go limits easily programmable in common tabular form. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
3 Series MDO -
Tektronix, Inc.
With the largest display in class, improved low-level signal measurement accuracy and industry-leading probe performance, the 3 Series MDO sets a new standard for bench oscilloscopes. Whether you’re testing your baseband design for IoT or just for simple EMI sniffing, the 3 Series has a unique true hardware spectrum analyzer built right in with superior RF test performance and guaranteed RF specifications.
-
PeakTech Prüf- und Messtechnik GmbH
The switching power supply technology used ensures high performance with a small size and low weight. 6 different DC output voltages (3 V / 4.5 V / 6 V / 7.5 V / 9 V and 12 V) can be set using a slider. With the 4 mm pole terminals, you can easily connect single wires but also 4 mm banana plugs. The power cord with an Euro plug is firmly connected to the power supply unit, whereby the device is switched off and on via a rear power switch. This handy power supply fits on every work bench and can be used universally in the hobby area, service or training.
-
Model Model 82 -
Mensor Corp.
The Mensor Model 82 is a pump and/or compressor set that complements a pressure controller and fits on or under a bench, in a rack, or on a table. The compressor is an oil-less pump with a maximum pressure of 50 psi with a open flow of 1.5 cfm. The vacuum pump is also oil-less and can achieve 28.5 inHG of vacuum with an open flow of 0.8 cfm. In avionics terms, this set is capable of 60,000 feet of altitude and airspeeds in excess of 1000 knots. Both units are shock mounted to reduce noise and vibration. Each unit has a power switch/breaker and can be run independently. This same configuration can also be produced in a standard 19 inch, 4U (7” high) rack mount chassis or desktop version.
-
LQ6324P -
Aplab Limited
- Multi Output Linear DC Power Supply- Digitally Controlled Output Settings- Store / Load 10 Sets of Output Settings in Internal Memory- USB Interface Provided- Programmable Arbitrary Variable Output by Feeding Coefficient of the Curve- User Friendly Front End- Low Cost General Purpose Laboratory Bench Unit- Fully Protected against Overload and Short Circuit- 5V/5A with Over Voltage Crowbar Protection for Digital ICs- Three Independent Outputs Electrically isolated from Each Other- Electrically Floating Outputs up to 500V DC w.r.t. Ground- Precise Regulation, Low Ripple and Noise for Both Constant Voltage & Current Operation
-
BMX -
Mountz Inc.
Meeting the demands to test multiple torque ranges for various torque tools used in production, maintenance and calibration labs, the versatile torque sensor is used in conjunction with a torque tester. The torque sensor is a bench mounted calibration instrument designed for torque wrench calibration, torque screwdriver calibration, and electric & pneumatic screwdriver calibration. Controlling torque is quintessential for companies to ensure their product's quality, safety and reliability isn't compromised.
-
SideWinder -
OtO Photonics Inc.
spectrometer ,built with the InGaAs type sensor and high performance 32bits RISC controller in, is specially designed for long wavelengths range. The optical engine is very simple and optimized for the spectrometer. The optical bench is very rigid and stable for measurement system, especially SW series has outstanding stability of thermo-hygro variation, vibration and shock on resolution and wavelength shift performance. The compact size is very flexible for system integration.
-
LINECHEK® II Series -
Associated Research
Our LINECHEK II Leakage Current Tester is designed for medical device manufacturers. With a feature set built around maximizing the efficiency of the Leakage Current test, LINECHEK II satisfies medical application requirements demanding up to 40 Amps of continuous line current. Use it on the bench or in a rack, from the front panel or via a PC interface to ensure your medical device is ready for global deployment.
